Date: Mon, 2 Jun 1997 13:49:54 +0200 From: "Andy Bontoft" <andy@bss.co.za> To: hackers@FreeBSD.ORG Subject: RE: SMC9332BDT help needed please Message-ID: <97Jun2.112637gmt%2B0200.17952-1@cerberus.bss.co.za>
next in thread | raw e-mail | index | archive | help
Hi I hope someone will be able to tell me what i'm doing wrong here. I'm trying to get an SMC9332BDT to work under 2.2.1-RELEASE (at 10Mbps). The card seems to be probed fine, and is initially being set to 100Mbps. The 'Link Integrity Indicator' (according to the manual) LED goes out as soon as the probe takes place and doesn't come back on. I have used ifconfig de0 -link2 to try and switch it over to 10Mbps and get kernel messages stating this is taking place. From this point on de0: transmission timeout messages are displayed although thay are not displayed before i try to switch the port. I have tried four different cards just to make sure it wasn't a dodgey card and used the SMC diagnostic program under DOS to transmit packets from the card which i can see with tcpdump on another machine.... Any ideas?? Thanx in advance for your time. andy BTW this card is UTP only, and i've searched through the old postings on www.freebsd.org but can't seem to find a solution. Boot and messages info.. CPU: Pentium (199.43-MHz 586-class CPU) Origin = "GenuineIntel" Id = 0x52c Stepping=12 Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8> real memory = 67108864 (65536K bytes) avail memory = 62599168 (61132K bytes) pcibus_setup(1): mode 1 addr port (0x0cf8) is 0x80000058 pcibus_setup(1a): mode1res=0x80000000 (0x80000000) pcibus_check: device 0 is there (id=12508086) Probing for devices on PCI bus 0: configuration mode 1 allows 32 devices. chip0 <Intel 82439> rev 3 on pci0:0 chip1 <Intel 82371SB PCI-ISA bridge> rev 1 on pci0:7:0 chip2 <Intel 82371SB IDE interface> rev 0 on pci0:7:1 mapreg[20] type=1 addr=0000f000 size=0010. I/O Recovery Timing: 8-bit 3.5 clocks, 16-bit 3.5 clocks Extended BIOS: disabled Lower BIOS: disabled Coprocessor IRQ13: disabled Mouse IRQ12: disabled Interrupt Routing: A: , B: , C: , D: MB0: , MB1: de0 <Digital 21140A Fast Ethernet> rev 34 int a irq 12 on pci0:17 mapreg[10] type=1 addr=00006100 size=0080. mapreg[14] type=0 addr=e0000000 size=0080. reg16: ioaddr=0x6100 size=0x80 de0: 21140A [10-100Mb/s] pass 2.2 de0: address 00:e0:29:06:3f:02 de0: enabling 100baseTX port [ snip ] May 31 18:32:26 skoll /kernel: de0: enabling 100baseTX port May 31 18:32:27 skoll /kernel: de0: enabling 10baseT port May 31 18:32:28 skoll /kernel: de0: transmission timeout May 31 18:32:32 skoll /kernel: de0: transmission timeout May 31 18:33:47 skoll /kernel: de0: transmission timeout
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?97Jun2.112637gmt%2B0200.17952-1>