Date: Mon, 23 Oct 2006 08:25:54 -0500 From: <Johannes.Kruger@nokia.com> To: <supportsobaka@mail.ru>, <freebsd-scsi@freebsd.org> Subject: RE: SR1500 + 5000PAL + SAS backplane - no RAID support Message-ID: <E9C6E9346955B54D9C707AA03EA5193A017F07BC@daebe102.NOE.Nokia.com> In-Reply-To: <1378533299.20061023170739@mail.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
#define MPI_EVENT_SAS_PHY_LINK_STATUS (0x00000012) #define MPI_EVENT_SAS_DISCOVERY_ERROR (0x00000013) #define MPI_EVENT_IR_RESYNC_UPDATE (0x00000014) #define MPI_EVENT_IR2 (0x00000015) #define MPI_EVENT_SAS_DISCOVERY (0x00000016) Event 0x16 just means that the card is probing for devices attached to the PHY's=20 In your case 0x12 means a device have been seen on a PHY P.S. If you get time and want to do me a favor, configure 2 drives on the controller in a RAID-1 configuration. Then do a disk test on the RAID-1 volume, say with iozone or any other method, and tell me your performance. I get slow RAID-1 performance, still cannot figure this out, ~5 Mbytse/sec instead of ~ 30 Mbytes/sec with no volume. With NCQ enabled it goes up to 15, but it' still not 30. I can get faster RAID-1 performance by implementing this in software doing parallel writes. Johan -----Original Message----- From: owner-freebsd-scsi@freebsd.org [mailto:owner-freebsd-scsi@freebsd.org]=20 Sent: Monday, October 23, 2006 9:08 AM To: freebsd-scsi@freebsd.org Subject: SR1500 + 5000PAL + SAS backplane - no RAID support Hello Sorry for bad English Dose anybody play with SR1500 + 5000PAL + SAS backplane ? In system BIOS I set SATA and PATA controller - Disable {it is controllers on motherboard 5000PAL} Mass storage controllers menu SAS controller - Enable {it is controller on backplane} SAS configure as SW RAID - Enable RAID was build in controller's BIOS (CTRL+E during boot). But in FreeBSD I have separated devices, no raid, and no way to build it in FreeBSD Releng_6 DMESG: Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 6.2-PRERELEASE #0: Fri Oct 20 21:04:52 MSD 2006 root@servertests.ru:/usr/home/obj/usr/src/sys/SERVERTESTS Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Xeon(TM) CPU 3.20GHz (3191.88-MHz 686-class CPU) Origin =3D "GenuineIntel" Id =3D 0xf64 Stepping =3D 4 =20 Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PG= E ,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=3D0xe43d<SSE3,RSVD2,MON,DS_CPL,VMX,CNTX-ID,CX16,<b14>,<b15>> AMD Features=3D0x20100000<NX,LM> AMD Features2=3D0x1<LAHF> Cores per package: 2 Logical CPUs per core: 2 real memory =3D 2143289344 (2044 MB) avail memory =3D 2090569728 (1993 MB) ACPI APIC Table: <INTEL S5000PAL> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 cpu4 (AP): APIC ID: 4 cpu5 (AP): APIC ID: 5 cpu6 (AP): APIC ID: 6 cpu7 (AP): APIC ID: 7 ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 24-47 on motherboard lapic0: Forcing LINT1 to edge trigger acpi0: <INTEL S5000PAL> on motherboard acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi0: Power Button (fixed) acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 cpu1: <ACPI CPU> on acpi0 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 cpu2: <ACPI CPU> on acpi0 acpi_throttle2: <ACPI CPU Throttling> on cpu2 acpi_throttle2: failed to attach P_CNT device_attach: acpi_throttle2 attach returned 6 cpu3: <ACPI CPU> on acpi0 acpi_throttle3: <ACPI CPU Throttling> on cpu3 acpi_throttle3: failed to attach P_CNT device_attach: acpi_throttle3 attach returned 6 cpu4: <ACPI CPU> on acpi0 acpi_throttle4: <ACPI CPU Throttling> on cpu4 acpi_throttle4: failed to attach P_CNT device_attach: acpi_throttle4 attach returned 6 cpu5: <ACPI CPU> on acpi0 acpi_throttle5: <ACPI CPU Throttling> on cpu5 acpi_throttle5: failed to attach P_CNT device_attach: acpi_throttle5 attach returned 6 cpu6: <ACPI CPU> on acpi0 acpi_throttle6: <ACPI CPU Throttling> on cpu6 acpi_throttle6: failed to attach P_CNT device_attach: acpi_throttle6 attach returned 6 cpu7: <ACPI CPU> on acpi0 acpi_throttle7: <ACPI CPU Throttling> on cpu7 acpi_throttle7: failed to attach P_CNT device_attach: acpi_throttle7 attach returned 6 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci1 pci2: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci2 pci3: <ACPI PCI bus> on pcib3 mpt0: <LSILogic SAS/SATA Adapter> port 0x3000-0x30ff mem 0xb8910000-0xb8913fff,0xb8900000-0xb890ffff irq 16 at device 0.0 on pci3 mpt0: [GIANT-LOCKED] mpt0: MPI Version=3D1.5.13.0 mpt0: mpt_cam_event: 0x16 mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). mpt0: mpt_cam_event: 0x12 mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). mpt0: mpt_cam_event: 0x12 mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). mpt0: mpt_cam_event: 0x12 mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). pcib4: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci2 pci4: <ACPI PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> irq 16 at device 2.0 on pci2 pci5: <ACPI PCI bus> on pcib5 em0: <Intel(R) PRO/1000 Network Connection Version - 6.1.4> port 0x2020-0x203f mem 0xb8820000-0xb883ffff,0xb8400000-0xb87fffff irq 18 at device 0.0 on pci5 em0: Ethernet address: 00:04:23:cf:79:50 em0: [FAST] em1: <Intel(R) PRO/1000 Network Connection Version - 6.1.4> port 0x2000-0x201f mem 0xb8800000-0xb881ffff,0xb8000000-0xb83fffff irq 19 at device 0.1 on pci5 em1: Ethernet address: 00:04:23:cf:79:51 em1: [FAST] pcib6: <ACPI PCI-PCI bridge> at device 0.3 on pci1 pci6: <ACPI PCI bus> on pcib6 pcib7: <PCI-PCI bridge> at device 3.0 on pci0 pci7: <PCI bus> on pcib7 pcib8: <ACPI PCI-PCI bridge> at device 4.0 on pci0 pci8: <ACPI PCI bus> on pcib8 pcib9: <ACPI PCI-PCI bridge> at device 5.0 on pci0 pci9: <ACPI PCI bus> on pcib9 pcib10: <ACPI PCI-PCI bridge> at device 6.0 on pci0 pci10: <ACPI PCI bus> on pcib10 pcib11: <ACPI PCI-PCI bridge> at device 7.0 on pci0 pci11: <ACPI PCI bus> on pcib11 pci0: <base peripheral> at device 8.0 (no driver attached) pcib12: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci12: <ACPI PCI bus> on pcib12 pci12: <display, VGA> at device 12.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus, SMBus> at device 31.3 (no driver attached) sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 flags 0x10 on acpi0 sio1: type 16550A, console atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xc9000-0xd07ff,0xd0800-0xd17ff,0xd1800-0xd27ff on isa0 ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 ata1 at port 0x170-0x177,0x376 irq 15 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=3D0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 1.000 msec ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding disabled, default to accept, logging limited to 100 packets/entry by default mpt0: mpt_cam_event: 0x16 mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). ses0 at mpt0 bus 0 target 4 lun 0 ses0: <ESG-SHV. SCA HSBP M10.... 1.41> Fixed Enclosure Services SCSI-3 device=20 ses0: 300.000MB/s transfers ses0: SCSI-3 SES Device da0 at mpt0 bus 0 target 0 lun 0 da0: <ATA WDC WD2500YS-01S 6C03> Fixed Direct Access SCSI-5 device=20 da0: 300.000MB/s transfers, Tagged Queueing Enabled da0: 239372MB (490234752 512 byte sectors: 255H 63S/T 30515C) da1 at mpt0 bus 0 target 1 lun 0 da1: <FUJITSU MAX3073RC 0104> Fixed Direct Access SCSI-3 device=20 da1: 300.000MB/s transfers, Tagged Queueing Enabled da1: 70136MB (143638992 512 byte sectors: 255H 63S/T 8941C) da2 at mpt0 bus 0 target 2 lun 0 da2: <FUJITSU MAX3073RC 0104> Fixed Direct Access SCSI-3 device=20 da2: 300.000MB/s transfers, Tagged Queueing Enabled da2: 70136MB (143638992 512 byte sectors: 255H 63S/T 8941C) lapic3: Forcing LINT1 to edge trigger SMP: AP CPU #3 Launched! lapic1: Forcing LINT1 to edge trigger SMP: AP CPU #1 Launched! lapic6: Forcing LINT1 to edge trigger SMP: AP CPU #6 Launched! lapic2: Forcing LINT1 to edge trigger SMP: AP CPU #2 Launched! lapic7: Forcing LINT1 to edge trigger SMP: AP CPU #7 Launched! lapic4: Forcing LINT1 to edge trigger SMP: AP CPU #4 Launched! lapic5: Forcing LINT1 to edge trigger SMP: AP CPU #5 Launched! Trying to mount root from ufs:/dev/da0s1a em0: link state changed to UP =3D=3D=3D=3D=3D Not mfi, not iir helped. Which driver must be used? Or FreeBSD just not supported LSISAS1054E with integrated RAID ? (http://www.lsi.com/storage_home/products_home/standard_product_ics/sas_ ics/lsisas1064e/index.html) Also what about mpt0: mpt_cam_event: 0x16 mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). Is it danger on production server? Thank you _______________________________________________ freebsd-scsi@freebsd.org mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-scsi To unsubscribe, send any mail to "freebsd-scsi-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?E9C6E9346955B54D9C707AA03EA5193A017F07BC>