Date: Thu, 16 Feb 2006 13:23:50 -0600 From: Andrew <andrew.chace@gmail.com> To: freebsd-questions@freebsd.org Subject: newly built kernel fails to boot Message-ID: <1140117830.602.19.camel@netvista.network>
next in thread | raw e-mail | index | archive | help
Hello, I've just had a go at configuring and rebuilding a kernel for my desktop machine. I read the section in handbook, and skimmed over NOTES and the GENERIC config. I then copied GENERIC to NETVISTA and commented out drivers/devices that I didn't think were relevant to my hardware. config(8) is happy with my file, and 'make buildkernel' and 'make installkernel' proceed without any errors. So, I ran nextboot(8) and rebooted, but the new kernel hangs right after the first line printed to the console; the first portion of which is 'acpi.ko'. Below are the output from dmesg on GENERIC and my kernel config: ============================ start of dmesg ============================ Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-RELEASE #0: Thu Nov 3 09:36:13 UTC 2005 root@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 1.80GHz (1794.19-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf24 Stepping = 4 Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM> real memory = 259522560 (247 MB) avail memory = 244412416 (233 MB) ACPI APIC Table: <PTLTD APIC > ioapic0 <Version 2.0> irqs 0-23 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <PTLTD RSDT> on motherboard acpi0: Power Button (fixed) pci_link0: <ACPI PCI Link LNKA> irq 11 on acpi0 pci_link1: <ACPI PCI Link LNKB> irq 9 on acpi0 pci_link2: <ACPI PCI Link LNKC> irq 5 on acpi0 pci_link3: <ACPI PCI Link LNKD> irq 10 on acpi0 pci_link4: <ACPI PCI Link LNKE> irq 11 on acpi0 pci_link5: <ACPI PCI Link LNKF> irq 0 on acpi0 pci_link6: <ACPI PCI Link LNKG> irq 0 on acpi0 pci_link7: <ACPI PCI Link LNKH> irq 9 on acpi0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <Intel 82845G (845G GMCH) SVGA controller> mem 0x88000000-0x8fffffff,0x80000000-0x8007ffff irq 16 at device 2.0 on pci0 agp0: detected 8060k stolen memory agp0: aperture size is 128M uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 16 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 19 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 18 at device 29.2 on pci0 uhci2: [GIANT-LOCKED] usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered ehci0: <Intel 82801DB/DBL/DBM (ICH4) USB 2.0 controller> mem 0xc0080000-0xc00803ff irq 23 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] usb3: EHCI version 1.0 usb3: companion controllers, 2 ports each: usb0 usb1 usb2 usb3: <Intel 82801DB/DBL/DBM (ICH4) USB 2.0 controller> on ehci0 usb3: USB revision 2.0 uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub3: 6 ports with 6 removable, self powered pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib1 fxp0: <Intel 82801DB (ICH4) Pro/100 VE Ethernet> port 0x2000-0x203f mem 0xc0100000-0xc0100fff irq 20 at device 8.0 on pci2 miibus0: <MII bus> on fxp0 inphy0: <i82562EM 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: Ethernet address: 00:09:6b:62:4b:99 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0 pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pcm0: <Intel ICH4 (82801DB)> port 0x1c00-0x1cff,0x18c0-0x18ff mem 0xc0080c00-0xc0080dff,0xc0080800-0xc00808ff irq 17 at device 31.5 on pci0 pcm0: [GIANT-LOCKED] pcm0: <Analog Devices AD1981A AC97 Codec> acpi_tz0: <Thermal Zone> on acpi0 acpi_tz0: _CRT value is absurd, ignored (6280.3C) acpi_button0: <Power Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse Explorer, device ID 4 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xcb000-0xcbfff,0xcc000-0xccfff,0xe0000-0xeffff on isa0 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 1794187328 Hz quality 800 Timecounters tick every 1.000 msec ad0: 76319MB <WDC WD800JB-00JJC0 05.01C05> at ata0-master UDMA100 acd0: DVDROM <HL-DT-STDVD-ROM GDR8163B/0B26> at ata1-master UDMA40 Trying to mount root from ufs:/dev/ad0s1a ============================ end of dmesg ============================== ======================== start of kernel config ======================== # NETVISTA Kernel Config # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ../../conf/NOTES and NOTES files. # If you are in doubt as to the purpose or necessity of a line, check first # in NOTES. machine i386 cpu I686_CPU ident NetVista #options CPU_SUSP_HLT options SCHED_ULE # ULE scheduler #options SCHED_4BSD # 4BSD scheduler options PREEMPTION # Enable kernel thread preemption options INET # InterNETworking options INET6 # IPv6 communications protocols options FFS # Berkeley Fast Filesystem options SOFTUPDATES # Enable FFS soft updates support options UFS_ACL # Support for access control lists options UFS_DIRHASH # Improve performance on big directories options MD_ROOT # MD is a potential root device options MSDOSFS # MSDOS Filesystem options CD9660 # ISO 9660 Filesystem options PROCFS # Process filesystem (requires PSEUDOFS) options LINPROCFS # Enable the linux-like proc filesystem support options PSEUDOFS # Pseudo-filesystem framework options GEOM_GPT # GUID Partition Tables. options COMPAT_43 # Compatible with BSD 4.3 [KEEP THIS!] options COMPAT_FREEBSD4 # Compatible with FreeBSD4 options COMPAT_FREEBSD5 # Compatible with FreeBSD5 options COMPAT_LINUX # Enable Linux ABI emulation options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI options KTRACE # ktrace(1) support options SYSVSHM # SYSV-style shared memory options SYSVMSG # SYSV-style message queues options SYSVSEM # SYSV-style semaphores options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions options KBD_INSTALL_CDEV # install a CDEV entry in /dev #options AHC_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~128k to driver. #options AHD_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~215k to driver. options ADAPTIVE_GIANT # Giant mutex is adaptive. device apic # I/O APIC device npx # The Numeric Processing eXtension driver, npx(4) # Bus support. device pci device isa # Required by npx(4) # Floppy drives device fdc # ATA and ATAPI devices device ata device atadisk # ATA disk drives device ataraid # ATA RAID drives device atapicd # ATAPI CDROM drives options ATA_STATIC_ID # Static device numbering # SCSI peripherals device scbus # SCSI bus (required for SCSI) device ch # SCSI media changers device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct SCSI access) device ses # SCSI Environmental Services (and SAF-TE) # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc # AT keyboard controller device atkbd # AT keyboard device psm # PS/2 mouse device vga # VGA video card driver device splash # Splash screen and screen saver support # syscons is the default console driver, resembling an SCO console #device sc # Enable this for the pcvt (VT220 compatible) console driver device vt options XSERVER # support for X server on a vt console device agp # support several AGP chipsets # Direct Rendering modules for 3D acceleration. device drm # DRM core module required by DRM drivers device i915drm # Intel i830 through i915 # Power management support (see NOTES for more options) #device apm # Add suspend/resume support for the i8254. device pmtimer # ACPI Video Extensions (LCD backlight/brightness, video output, etc.) device acpi_video # Serial (COM) ports device sio # 8250, 16[45]50 based serial ports # Parallel port device ppc device ppbus # Parallel port bus (required) device lpt # Printer device ppi # Parallel port interface device # PCI Ethernet NICs that use the common MII bus controller code. device miibus # MII bus support device fxp # Intel EtherExpress PRO/100B (82557, 82558) device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # Pseudo devices. device loop # Network loopback device random # Entropy device device ether # Ethernet support device sl # Kernel SLIP device ppp # Kernel PPP device tun # Packet tunnel. device pty # Pseudo-ttys (telnet etc) device md # Memory "disks" device gif # IPv6 and IPv4 tunneling device faith # IPv6-to-IPv4 relaying (translation) # The `bpf' device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! # Note that 'bpf' is required for DHCP. device bpf # Berkeley packet filter # USB support device uhci # UHCI PCI->USB interface device ohci # OHCI PCI->USB interface device ehci # EHCI PCI->USB interface (USB 2.0) device usb # USB Bus (required) device ugen # Generic device uhid # "Human Interface Devices" device ukbd # Keyboard device ulpt # Printer device umass # Disks/Mass storage - Requires scbus and da device ums # Mouse ======================== end of kernel config ========================= Thanks to anyone willing to take a look at this :-)! -Andrew
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1140117830.602.19.camel>