From owner-freebsd-questions Fri Dec 28 18:57:39 2001 Delivered-To: freebsd-questions@freebsd.org Received: from smtp-send.myrealbox.com (smtp-send.myrealbox.com [192.108.102.143]) by hub.freebsd.org (Postfix) with ESMTP id 8948437B405 for ; Fri, 28 Dec 2001 18:57:33 -0800 (PST) Received: from Tom_Parquette [24.24.29.69] by myrealbox.com with NIMS ModWeb Module; Fri, 28 Dec 2001 21:57:22 -0500 Subject: Re: Re: 3c509 nic, kernel, resulting confusion??? From: Tom Parquette To: printery@blkft.com, Cc: freebsd-questions@FreeBSD.ORG, Date: Fri, 28 Dec 2001 21:57:22 -0500 X-Mailer: NIMS ModWeb Module X-Sender: Tom_Parquette MIME-Version: 1.0 Message-ID: <1009594642.4bfaeff2Tom_Parquette@myrealbox.com> Content-Type: text/plain; charset="UTF-8" Content-Transfer-Encoding: quoted-printable Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk List-ID: List-Archive: (Web Archive) List-Help: (List Instructions) List-Subscribe: List-Unsubscribe: X-Loop: FreeBSD.ORG Terri, I cannot comment on your 7% loss pinging localhost. That sounds seriously out of whack to me. Re: The 3C509-combo card: Your demesg output looks like the card was at least partially autoconfigure= d to be the second card in the box. (Based on the port at 210. The ethe= rdisk autoconfigure will select 300 if it is the only card.) It's also a combo card based on your demesg output. Your ifconfig -a look= s ok but I have to ask, are you using the RJ-45 interface or one of the o= thers? I have had to manually configure the interface for 10Base-2 befor= e. For some reason, autodetect seems to default to the RJ-45 even if my = 10Base-2 T fitting is plugged in. Suggestions: If this is the only LAN card in your box, get the current Etherdisk from 3C= om's web site (WWW.3com.com) and allow 3c5x9cfg to automatically configur= e the card. If you are using something other than the RJ-45 interface, c= hange the interface specification from autodetect to whatever you are usi= ng. You might want to consider specifying the interface even if autodete= ct appears to be guessing right. If this is not the only LAN card in your box, let 3c5x9cfg try to configure= your card but check for conflicts. When I do this, I have a hardcopy of= demsg to compare the tool's selections against. Again, watch out for the= selection of the physical lan interface plug that it is coming up with. If you have another FreeBSD box on the same wire, I'm assuming you are not = using a switched hub, having a TCPDUMP going at the same time you try to = ping can give you a clue if you are making it out onto the wire. I've had good luck with the 3Com cards at home and at work. They do have t= heir quirks though. Cheers... -----Original Message----- From: "Terry Thomas" To: Date: Fri, 28 Dec 2001 14:17:10 -0800 Subject: Re: 3c509 nic, kernel, resulting confusion??? Correction: It will ping 127.0.0.1 with a 7% loss but ping takes a long tim= e to start, pings to outside or my router come back 'send to: host is down' ----- Original Message ----- From: "printery-blkft" To: Sent: Friday, December 28, 2001 1:53 PM Subject: 3c509 nic, kernel, resulting confusion??? > I'm running 4.4 stable with a 3c509c nic, i've csvuped and went thru > buildworld, etc. with no errors and i've been trying to get it set up for > over a week now and i've not been successful. > I have a 56k frame with 16 ip#'s and a rh box connected to a cisco router > that's up and i'm trying to get my fbsd box hooked via the switch to it too > but it won't even ping 127.0.0.1 > here's what i have set so far, maybe someone can help?? > > in etc/rc.conf i've added... > ifconfig_ep0=3D"inet xxx.xxx.xxx.67" netmask=3D"255.255.255.240" > defaultrouter=3D"xxx.xxx.xxx.65" > > device ep0 isn't in /dev and i've tried to add it with > /dev/MAKEDEV ep0 > but it says device not present > > ifconfig -a gives me... > ep0: flags=3D8843 mtu 1500 > inet xxx.xxx.xxx.67 netmask 0xfffffff0 broadcast xxx.xxx.xxx.79 > inet6 fe80::260:8f:fe20:1cca%ep0 prefixlen 64 scopeid 0x1 > ehter 00:60:08:20:1c:ca > media: Ethernet 10baseT/UTP > > netstat -rn gives me... > 127.0.0.1 127.0.0.1 UH 0 0 lo0 > xxx.xxx.xxx.64/28 link#1 UC 1 0 ep0 > Internet6 has these lines... > fe80::%ep0/64 link#1 UC ep0 > ff02::%ep0/32 link#1 UC ep0 > > dmesg has... > ep0: <3com 3c509-combo etherlink III at port 0x210 irq 11 on isa0 > ep0: > etc/resolv.conf is... > 127.0.0.1 localhost.xxxxx.com localhost > xxx.xxx.xxx.67 ns2.xxxxx.com ns2 > xxx.xxx.xxx.67 ns2.xxxxx.com. > > etc/hosts is... > domain xxxxx.com > nameserver xxx.xxx.xxx.66 (my redhat dns) > nameserver xxx.xxx.xx.3 (my isp nameserver) > > > What am I doing wrong??? or What am I missing? > Needless to say, I'm new at this! I was able to setup ppp with no proble= m > but this ethernet/nic thing has me stumped! > > Thank You, > Terry Thomas > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message Try not. Do or do not. There is no try. -- Yoda To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message