From owner-freebsd-current Sat Oct 28 15:11:11 1995 Return-Path: owner-current Received: (from root@localhost) by freefall.freebsd.org (8.6.12/8.6.6) id PAA02849 for current-outgoing; Sat, 28 Oct 1995 15:11:11 -0700 Received: from ast.com (irvine.ast.com [165.164.128.2]) by freefall.freebsd.org (8.6.12/8.6.6) with SMTP id PAA02836 for ; Sat, 28 Oct 1995 15:11:06 -0700 Received: from fw.ast.com by ast.com with SMTP id AA05953 (5.67b/IDA-1.5 for ); Sat, 28 Oct 1995 15:12:15 -0700 Received: from nemesis by fw.ast.com with uucp (Smail3.1.29.1 #4) id m0t9JOP-000089C; Sat, 28 Oct 95 17:06 CDT Received: by nemesis.lonestar.org (Smail3.1.27.1 #19) id m0t9JMV-000IyNC; Sat, 28 Oct 95 17:04 WET DST Message-Id: Date: Sat, 28 Oct 95 17:04 WET DST To: current@Freebsd.org From: uhclem%nemesis@fw.ast.com (Frank Durda IV) Sent: Sat Oct 28 1995, 17:04:23 CDT Subject: Support for WD8003E abandoned? Sender: owner-current@Freebsd.org Precedence: bulk I have a site that has been trying to install 2.0.5, toying with a migration from Linux. However, the WD8003E card he has is not detected under FreeBSD, despite carefully setting all the parameters in UserConfig. I plan to visit the site today, but since this guy installs hardware for ISPs, I think he knows what he is doing. I tried the same thing on 2.1.0-951026-SNAP on three WD8003EB boards I have around here. They are all detected, but none work! I removed the 8013EW-C board I had installed (and working great) and replaced it with one of the WD8003EB boards. I/O port for all boards is 0x280, memory address for all is 0xd4000. On the WD8003EB boards, I tried interrupt 2, 3 and 7. None seem to work. I always get ed0: timeout errors. (LPT1 was changed in the EISA config to LPT2/IRQ5 and COM2 was disabled. I ran the 8013 on IRQ 2 and the 8003EB works well on IRQ2/9 under DOS.) On the WD8003EB boards, INIT is not strapped and ROM SIZE is set to 16K, although no ROM is present. the AUI/BNC straps are set to BNC. The only interrupt choices available on these boards is 2, 3, 4, and 7, according to EZSETUP 2.1, 4.4 and 4.6. Did we drop support of these 8-bit cards and I wasn't paying attention? Whatever the problem is, it might reach back to 2.0.5RELEASE. The card I am looking at right now (that works under DOS and Windows '95 - I don't have Linux anywhere) says: WD8003EB X7 37901 61-600245-06 MADE IN P.R. I'll be happy to dig into this further if someone can provide a direction. Thanks. Frank Durda IV |"The Knights who say "LETNi" or uhclem%nemesis@fw.ast.com (Fastest Route)| demand... A SEGMENT REGISTER!!!" ...letni!rwsys!nemesis!uhclem |"A what?" ...decvax!fw.ast.com!nemesis!uhclem |"LETNi! LETNi! LETNi!" - 1983