Date: Sat, 14 Sep 2002 12:56:53 +0800 From: =?gb2312?B?zrogxuTOxA==?= <qiwenwei@hotmail.com> To: freebsd-questions@FreeBSD.ORG Subject: about 3com FE575 PCMCIA card! Message-ID: <F3688mtzy3qgzfPhyvS0001e038@hotmail.com>
next in thread | raw e-mail | index | archive | help
>I have a DELL Latitude laptop which have 2 PCMCIA cards,one is a modem,the
>other is
>3COM FE575 ethernet card,when i start my FreeBSD4.6.2,there are some
message
>say my ethernet card cannot work,here is my dmesg:
>
>Copyright (c) 1992-2002 The FreeBSD Project.
>Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
>FreeBSD 4.6.2-RELEASE #0: Wed Aug 14 21:23:26 GMT 2002
> murray@builder.freebsdmall.com:/usr/src/sys/compile/GENERIC
>Timecounter "i8254" frequency 1193182 Hz
>CPU: Pentium III/Pentium III Xeon/Celeron (747.70-MHz 686-class CPU)
> Origin = "GenuineIntel" Id = 0x686 Stepping = 6
>
>Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
>PAT,PSE36,MMX,FXSR,SSE>
>real memory = 268283904 (261996K bytes)
>avail memory = 256126976 (250124K bytes)
>Preloaded elf kernel "kernel" at 0xc04d0000.
>Pentium Pro MTRR support enabled
>md0: Malloc disk
>Using $PIR table, 9 entries at 0xc00fbd80
>npx0: <math processor> on motherboard
>npx0: INT 16 interface
>pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
>pci0: <PCI bus> on pcib0
>pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
>pci1: <PCI bus> on pcib1
>pci1: <ATI model 4c46 graphics accelerator> at 0.0 irq 11
>pcic0: <TI PCI-1420 PCI-CardBus Bridge> irq 11 at device 3.0 on pci0
>pcic0: PCI Memory allocated: 0x44000000
>pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][CSC serial isa
>irq]
>pccard0: <PC Card bus (classic)> on pcic0
>pcic1: <TI PCI-1420 PCI-CardBus Bridge> irq 11 at device 3.1 on pci0
>pcic1: PCI Memory allocated: 0x44001000
>pcic1: TI12XX PCI Config Reg: [ring enable][speaker enable][CSC serial isa
>irq]
>pccard1: <PC Card bus (classic)> on pcic1
>isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
>isa0: <ISA bus> on isab0
>atapci0: <Intel PIIX4 ATA33 controller> port 0x860-0x86f at device 7.1 on
>pci0
>ata0: at 0x1f0 irq 14 on atapci0
>ata1: at 0x170 irq 15 on atapci0
>uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xdce0-0xdcff irq 11
>at device 7.2 on pci0
>usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
>usb0: USB revision 1.0
>uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>uhub0: 2 ports with 2 removable, self powered
>chip1: <Intel 82371AB Power management controller> port 0x840-0x84f at
>device 7.3 on pci0
>pci0: <unknown card> (vendor=0x125d, dev=0x1998) at 8.0 irq 5
>orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
>fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
>fdc0: FIFO enabled, 8 bytes threshold
>fd0: <1440-KB 3.5" drive> on fdc0 drive 0
>atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
>atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
>kbd0 at atkbd0
>psm0: <PS/2 Mouse> irq 12 on atkbdc0
>psm0: model IntelliMouse, device ID 3
>vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
>sc0: <System console> at flags 0x100 on isa0
>sc0: VGA <16 virtual consoles, flags=0x300>
>sio0: configured irq 4 not in bitmap of probed irqs 0
>sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
>sio0: type 16550A
>sio1: configured irq 3 not in bitmap of probed irqs 0
>ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
>ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
>ppc0: FIFO with 16/16/8 bytes threshold
>plip0: <PLIP network interface> on ppbus0
>lpt0: <Printer> on ppbus0
>lpt0: Interrupt-driven port
>ppi0: <Parallel I/O> on ppbus0
>ad0: 19077MB <TOSHIBA MK2018GAS> [38760/16/63] at ata0-master UDMA33
>Mounting root from ufs:/dev/ad0s3a
>ad0s6: slice starts beyond end of the disk: rejecting it
>ad0s6: slice starts beyond end of the disk: rejecting it
>pccard: card inserted, slot 0
>pccard: card inserted, slot 1
>pccard: card removed, slot 0
>pcic0: Card type 32-bit cardbus is unsupported
>pccard: card removed, slot 1
>pccard: card inserted, slot 1
>sio4 at port 0x2f8-0x2ff irq 11 flags 0x40000 slot 1 on pccard1
>sio4: type 16550A
>sio4: unable to activate interrupt in fast mode - using normal mode
>
>
>can i make 3com fe575 working by changing the IRQ, port, and IOMEM of the
>file pccard.conf or other files?
>
> this card can be recongnized by openbsd, it is 3com 3c575c-tx,irq 11.
but i
>like FreeBSD more.
>
> if there are no ways can make this card working under 4.6,will it work
>under your next version 5.0?
>
>any help,thanks !!!!!
>
>
>
>best regards!
>
>Freebsd newbies,kevin
>
Best regards
Kevin.wei
魏其文
13322804065
_________________________________________________________________
与联机的朋友进行交流，请使用 MSN Messenger:
http://messenger.microsoft.com/cn/
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?F3688mtzy3qgzfPhyvS0001e038>