Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 08 Nov 2000 15:57:10 +0000
From:      Nick Barnes <Nick.Barnes@pobox.com>
To:        freebsd-multimedia@freebsd.org, freebsd-hardware@freebsd.org
Subject:   Intel D815EEA motherboard sound and network
Message-ID:  <4453.973699030@raven.ravenbrook.com>

next in thread | raw e-mail | index | archive | help
I have a new PC with an Intel D815EEA motherboard.  This comes with
onboard sound, network, and display.  I have a Matrox graphics card so
I don't care about the onboard display.

The motherboard doc claims that the network is compatible with Intel
Pro 100, so I expected it to show up as fxp0; it didn't.  Archives of
freebsd-hardware suggest this is known and unlikely to be fixed.  Oh
well. I've put a RealTek NIC in instead.

The motherboard doc also claims that the sound is compatible with
SoundBlaster PCI 128.  I've never used sound under FreeBSD, so I'm a
bit of a novice here.  Can someone advise me what I need in my kernel
config to drive this?  I've tried a couple of things (pcm, snd) with
no visible effect on the dmesg.

Here's a verbose boot with GENERIC.  Note also the "Bad PnP BIOS data
checksum" message.

Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Fri Jul 28 14:30:31 GMT 2000
jkh@ref4.freebsd.org:/usr/src/sys/compile/GENERIC
Calibrating clock(s) ... TSC clock: 797557265 Hz, i8254 clock: 1193154 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254"  frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium III/Pentium III Xeon/Celeron (797.58-MHz 686-class CPU)
Origin = "GenuineIntel"  Id = 0x686  Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory  = 268173312 (261888K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00426000 - 0x0ffb7fff, 263790592 bytes (64402 pages)
avail memory = 256700416 (250684K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fda60
bios32: Entry = 0xfda74 (c00fda74)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xda95
pnpbios: Bad PnP BIOS data checksum
Other BIOS signatures found:
ACPI: 000ff980
Preloaded elf kernel "kernel.GENERIC" at 0xc040d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
pci_open(1):    mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=11308086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1):    mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=11308086)
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x1130, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
map[10]: type 1, range 32, base f8000000, size 26
found-> vendor=0x8086, dev=0x1131, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=2        secondarybus=2
found-> vendor=0x8086, dev=0x244e, revid=0x01
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1        secondarybus=1
found-> vendor=0x8086, dev=0x2440, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0        secondarybus=0
found-> vendor=0x8086, dev=0x244b, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
map[20]: type 1, range 32, base 0000ffa0, size  4
found-> vendor=0x8086, dev=0x2442, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
intpin=d, irq=11
map[20]: type 1, range 32, base 0000ef40, size  5
found-> vendor=0x8086, dev=0x2443, revid=0x01
class=0c-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
intpin=b, irq=9
map[20]: type 1, range 32, base 0000efa0, size  4
found-> vendor=0x8086, dev=0x2444, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
intpin=c, irq=10
map[20]: type 1, range 32, base 0000ef80, size  5
found-> vendor=0x8086, dev=0x2445, revid=0x01
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
intpin=b, irq=9
map[10]: type 1, range 32, base 0000e800, size  8
map[14]: type 1, range 32, base 0000ef00, size  6
pci0: <PCI bus> on pcib0
pcib1: <PCI to PCI bridge (vendor=8086 device=1131)> at device 1.0 on pci0
found-> vendor=0x102b, dev=0x0525, revid=0x04
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base f2000000, size 25
map[14]: type 1, range 32, base feafc000, size 14
map[18]: type 1, range 32, base fe000000, size 23
pci2: <PCI bus> on pcib1
pci2: <Matrox MGA G400 AGP graphics accelerator> (vendor=0x102b, dev=0x0525) at 0.0 irq 11
pcib2: <PCI to PCI bridge (vendor=8086 device=244e)> at device 30.0 on pci0
found-> vendor=0x8086, dev=0x2449, revid=0x01
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base fd9fe000, size 12
map[14]: type 1, range 32, base 0000df00, size  6
found-> vendor=0x10ec, dev=0x8139, revid=0x10
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0        secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 0000d800, size  8
map[14]: type 1, range 32, base fd9ffc00, size  8
pci1: <PCI bus> on pcib2
pci1: <unknown card> (vendor=0x8086, dev=0x2449) at 8.0 irq 11
rl0: <RealTek 8139 10/100BaseTX> port 0xd800-0xd8ff mem 0xfd9ffc00-0xfd9ffcff irq 11 at device 13.0 on pci1
rl0: Ethernet address: 00:50:fc:01:f4:0e
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: rl0 attached
isab0: <PCI to ISA bridge (vendor=8086 device=2440)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xffa0
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xffa8
ata1: mask=03 status0=50 status1=00
ata1: mask=03 status0=10 status1=00
ata1: devices = 0x4
ata1: at 0x170 irq 15 on atapci0
uhci0: <UHCI (generic) USB controller> port 0xef40-0xef5f irq 11 at device 31.2 on pci0
uhci0: (New UHCI DeviceId=0x24428086)
using shared irq11.
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: (0x24428086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port 1 power on failed, IOERROR
uhub0: port 2 power on failed, IOERROR
pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 9
uhci1: <UHCI (generic) USB controller> port 0xef80-0xef9f irq 10 at device 31.4 on pci0
uhci1: (New UHCI DeviceId=0x24448086)
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: (0x24448086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub1: port 1 power on failed, IOERROR
uhub1: port 2 power on failed, IOERROR
pci0: <unknown card> (vendor=0x8086, dev=0x2445) at 31.5 irq 9
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
bt0: Failed Status Reg Test - fe
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
aha0: status reg test failed fe
aha0: status reg test failed ff
ated 4 times
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 06 05
psm: data 08 01 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio 68cc40, tty 63109a, net 67189a
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: faith0 attached
ad0: <IBM-DTLA-307045/TX6OA60A> ATA-5 disk at ata0 as master
ad0: 43979MB (90069840 sectors), 89355 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 32 depth queue, BIOSDMA
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
Creating DISK ad0
Creating DISK wd0
ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata1-master: success setting up PIO4 mode on generic chip
acd0: <SAMSUNG CD-ROM SC-152C/CS02> CDROM drive at ata1 as master
acd0: read 171KB/s (8937KB/s), 128KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 41929649, size 41929587 : OK
start_init: trying /sbin/init


--
FreeBSD 2.2.8-RELEASE: up 6 days, 5:09
last reboot Thu Nov 2 10:55 (lightning strike)


To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4453.973699030>