From owner-freebsd-questions Sat Sep 16 0:36:16 2000 Delivered-To: freebsd-questions@freebsd.org Received: from 2711.dynacom.net (2711.dynacom.net [206.107.213.3]) by hub.freebsd.org (Postfix) with ESMTP id D9B6437B423 for ; Sat, 16 Sep 2000 00:36:12 -0700 (PDT) Received: from urx.com (dsl1-160.dynacom.net [206.159.132.160]) by 2711.dynacom.net (Build 101 8.9.3/NT-8.9.3) with ESMTP id AAA01513; Sat, 16 Sep 2000 00:36:11 -0700 Message-ID: <39C322EB.2E026026@urx.com> Date: Sat, 16 Sep 2000 00:36:11 -0700 From: Kent Stewart Reply-To: kstewart@urx.com Organization: Dynacom X-Mailer: Mozilla 4.75 [en] (Windows NT 5.0; U) X-Accept-Language: en MIME-Version: 1.0 To: "Tomlinson, Drew" Cc: "'FreeBSD Questions (E-mail)'" Subject: Re: Help re: Make Install Kernel=MYKERNEL References: <8C224DC088D8D111B67D0000F67AC17E029C4C91@ldcmsx01.lc.ca.gov> Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG > "Tomlinson, Drew" wrote: > > [snip] > > > > Ok, I've completed all of the steps and the new kernel boots. > > > However, I'm still not sure if I had my kernel config file > correct. > > > I can't mount my CDROM drive. And I concerned about the line > "isa0: > > > too many dependant configs (8)". Can you see any problems? My > > > kernel config follows the boot messages for your reference. > > > > I don't know about the isa0 either but down below you have a acd0c > > > CDROM and you should be able to just say "mount /cdrom" > > OK, thanks. I was suffering from cerebral flatulence and trying > "mount /cd9660". :) I always heard that was a Braino. That was funny. You shouldn't forget that for a few days :). You never know what game your mind will pull on you. It was almost bad enough to be what I call a flat-forehead error. If you whack your forehead enough times, it will start to flatten out. > > [snip] > > > > Doing initial network setup: hostname domain. > > > ed0: flags=8843 mtu 1500 > > > > inet 192.168.0.5 netmask 0xffffff00 broadcast > 192.168.0.255 > > > inet6 fe80::240:5ff:fe66:b255%ed0 prefixlen 64 tentative > > > > scopeid 0x2 > > > ether 00:40:05:66:b2:55 > > > lo0: flags=8049 mtu 16384 > > > inet6 fe80::1%lo0 prefixlen 64 scopeid 0xa > > > inet6 ::1 prefixlen 128 > > > inet 127.0.0.1 netmask 0xff000000 > > > add net default: gateway 192.168.0.254 > > > > You have your ed0 NIC now. Can you ping your machine from one of > the > > other systems? You should be able to use your network at this > point. > > Your ed0 parameters look good. What about your resolv.conf and > hosts? > > [snip] > > > > My kernel config file: > > [snip] > > > You have some excess stuff here > > What can I get rid of? I think you can get rid of all of the next 6 devices but not any of the pseudo's.. > > > > > > > > > device ie0 at isa? port 0x300 irq 10 iomem 0xd0000 > > > device fe0 at isa? port 0x300 > > > device le0 at isa? port 0x300 irq 5 iomem 0xd0000 > > > device lnc0 at isa? port 0x280 irq 10 drq 0 > > > device cs0 at isa? port 0x300 > > > device sn0 at isa? port 0x300 irq 10 > > > # requires PCCARD (PCMCIA) support to be activated > > > #device xe0 at isa? > > > > > > # Pseudo devices - the number indicates how many units to > allocated. > > > > > > pseudo-device loop # Network loopback > > > pseudo-device ether # Ethernet support > > > pseudo-device sl 1 # Kernel SLIP > > > pseudo-device ppp 1 # Kernel PPP > > > pseudo-device tun # Packet tunnel. > > > pseudo-device pty # Pseudo-ttys (telnet etc) > > > pseudo-device md # Memory "disks" > > > pseudo-device gif 4 # IPv6 and IPv4 tunneling > > > pseudo-device faith 1 # IPv6-to-IPv4 relaying > > > (translation) > > > > > > # The `bpf' pseudo-device enables the Berkeley Packet Filter. > > > # Be aware of the administrative consequences of enabling this! > > > pseudo-device bpf #Berkeley packet filter > > > > > > # USB support > > > ...All commented out... > > > > > > # USB Ethernet, requires mii > > > ...All commented out... > > > > I would comment out all of the IPv6 stuff. What is your network > status > > at this point? > > My network is up. I can ping, telnet, ftp, etc. Once I sucessfully > compiled my kernel, the networking stuff resolved itself. > Everything seems to be working OK. You got to see the effect of an out of sync world up front. All too often people get by with things and then they hit the problem. Their "but it worked before" doesn't mean much :). > > Is there any pressing need to recompile without the IPV6 and the > excess stuff you mention above? If there's not, then I will wait as > my 486 seems to take about 4 hours to build and install a new > kernel. No pressing need for this or the excess devices. You can just make them comments and wait for when you have a real need to compile your kernel. Just remember that you changed them so that if they don't work you can back out the changes. It has been a real struggle and when there is a sense of victory is when it is time to relax for a little while. > > Your help has been invaluable and I thank you. Now I'm off to DNS > (which I know nothing about either) :) I don't run named on my system. I use my ISP dns servers. I add two lines to resolv.conf and by-pass some work on my part. There are times when I wish I had spent the time but the need wasn't bad enough to get me started. Kent -- Kent Stewart Richland, WA mailto:kbstew99@hotmail.com http://kstewart.urx.com/kstewart/index.html FreeBSD News http://daily.daemonnews.org/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message