Date: Mon, 30 Aug 2004 20:18:11 +0200 From: "Lukas Razik" <lukas@razik.de> To: freebsd-hardware@freebsd.org Subject: [5.3-BETA2] acd0: FAILURE - READ_BIG HARDWARE ERROR Message-ID: <163331489@web.de>
next in thread | raw e-mail | index | archive | help
Hi!!! I've a little problem with the 5.3-BETA2 because If I try to mount the acd0 device it doesn't work. I always get this: acd0: FAILURE - READ_BIG HARDWARE ERROR asc=0x08 ascq=0x03 error=0 No problems with acd1. Another error message I get is: Interrupt storm detected on "irq11: acpi0"; throttling interrupt source I had no other errors/panics during installation and the rest of the system works fine. There were no problems with earlier 5.X.X and my acd0: DVDROM <Pioneer DVD-ROM ATAPIModel DVD-106S 0122/E1.22> at ata0-master UDMA66 Regards, Lukas Here the whole dmesg: =================== Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-BETA2 #1: Sat Aug 28 21:29:15 UTC 2004 root@mack.dcsl.buffalo.edu:/usr/obj/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. ACPI APIC Table: <VIA692 AWRDACPI> Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel Pentium III (801.82-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 1610547200 (1535 MB) avail memory = 1568518144 (1495 MB) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 <Version 1.1> irqs 0-23 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <VIA692 AWRDACPI> on motherboard acpi0: Power Button (fixed) Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 cpu0: <ACPI CPU (3 Cx states)> on acpi0 cpu1: <ACPI CPU (3 Cx states)> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0 pcib0: could not get PCI interrupt routing table for \\_SB_.PCI0 - AE_BAD_DATA pci0: <ACPI PCI bus> on pcib0 pcib0: no PRT entry for 0.7.INTD agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pcib0: no PRT entry for 0.1.INTA pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 82C596B UDMA66 controller> port 0xc000-0xc00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 uhci0: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 9 at device 7.2 on pci0 uhci0: [GIANT-LOCKED] usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) fxp0: <Intel 82557 Pro/100 Ethernet> port 0xc800-0xc81f mem 0xe7000000-0xe70fffff,0xe7103000-0xe7103fff irq 17 at device 9.0 on pci0 miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: Ethernet address: 00:a0:c9:c5:8a:24 fxp0: [GIANT-LOCKED] uhci1: <VIA 83C572 USB controller> port 0xcc00-0xcc1f irq 18 at device 10.0 on pci0 uhci1: [GIANT-LOCKED] usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered ugen0: SiW SiW, rev 1.10/15.00, addr 2 uhci2: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 19 at device 10.1 on pci0 uhci2: [GIANT-LOCKED] usb2: <VIA 83C572 USB controller> on uhci2 usb2: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uscanner0: EPSON EPSON Scanner, rev 2.00/1.00, addr 2 pci0: <serial bus, USB> at device 10.2 (no driver attached) atapci1: <HighPoint HPT370 UDMA100 controller> port 0xe400-0xe4ff,0xe000-0xe003,0xdc00-0xdc07,0xd800-0xd803,0xd400-0xd407 irq 16 at device 11.0 on pci0 ata2: channel #0 on atapci1 ata3: channel #1 on atapci1 pcib2: <PCI-PCI bridge> at device 12.0 on pci0 pci2: <PCI bus> on pcib2 mlx0: <Mylex version 4 RAID interface> mem 0xe7100000-0xe7101fff irq 18 at device 12.1 on pci0 mlx0: [GIANT-LOCKED] mlx0: DAC960PG, 3 channels, firmware 4.06-0-08, 8MB RAM mlxd0: <Mylex System Drive> on mlx0 mlxd0: 26280MB (53821440 sectors) RAID 5 (online) mlxd1: <Mylex System Drive> on mlx0 mlxd1: 8678MB (17772544 sectors) RAID 1 (online) pcm0: <Creative CT5880-C> port 0xe800-0xe83f irq 19 at device 13.0 on pci0 pcm0: <TriTech TR28602 AC97 Codec> pcm0: [GIANT-LOCKED] fdc0: <floppy drive controller> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/16 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3 orm0: <ISA Option ROMs> at iomem 0xd4000-0xd6fff,0xd0000-0xd3fff,0xc0000-0xcffff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec ATAPI_RESET time = 40us acd0: DVDROM <Pioneer DVD-ROM ATAPIModel DVD-106S 0122/E1.22> at ata0-master UDMA66 ATAPI_RESET time = 140us acd1: CDRW <CR-48X5TE/1.8A> at ata1-slave PIO4 ad4: 28629MB <ST330620A/3.05> [58168/16/63] at ata2-master UDMA100 ad6: 28629MB <ST330620A/3.05> [58168/16/63] at ata3-master UDMA100 ar0: 57259MB <ATA RAID0 array> [7299/255/63] status: READY subdisks: disk0 READY on ad4 at ata2-master disk1 READY on ad6 at ata3-master SMP: AP CPU #1 Launched! Mounting root from ufs:/dev/mlxd0s1a Interrupt storm detected on "irq11: acpi0"; throttling interrupt source acd0: FAILURE - READ_BIG HARDWARE ERROR asc=0x08 ascq=0x03 error=0
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?163331489>