Date: 23 May 2001 18:02:52 +0200 From: Juan Jose Garcia Ripoll <jjgarcia@ind-cr.uclm.es> To: freebsd-stable@FreeBSD.ORG Subject: SMP lockups with 4.3 Message-ID: <87k838njdf.fsf@mobile-ripoll.arrakis.es>
next in thread | raw e-mail | index | archive | help
--Multipart_Wed_May_23_18:02:52_2001-1
Content-Type: text/plain; charset=US-ASCII
Hi,
I have upgraded two machines from 4.2 to 4.3 using cvsup. The first
one is the laptop I am writing on, and it works ok; the second one is
a dual PIII/700 with a MS motherbard.
It is this second machine the one which experiences lockups with a 4.3
SMP kernel as cvsuped last week. Booting with a single processor 4.2
kernel solves the problem. The machine is almost bare bones, with
apache and qpopper, and since everything works with 4.2 I suspect the
problem is related to a change in the SMP kernel.
As a side note, the same machine worked ok with Debian using a SMP
linux kernel. I just replaced it with FreeBSD because I find the
latter easier to maintain.
The output of dmesg with the 4.2 is below, together with one of the
4.3 kernels I have tried. What do you think I should do now?
TIA
Juanjo
--Multipart_Wed_May_23_18:02:52_2001-1
Content-Type: text/plain; charset=US-ASCII
Content-Disposition: inline; filename="DMESG.TXT"
Content-Transfer-Encoding: quoted-printable
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.2-RELEASE #0: Mon Nov 20 13:02:55 GMT 2000
jkh@bento.FreeBSD.org:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (735.00-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x686 Stepping =3D 6
Features=3D0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory =3D 134152192 (131008K bytes)
avail memory =3D 126328832 (123368K bytes)
Preloaded elf kernel "kernel.old" at 0xc0436000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on =
pci0
pci1: <PCI bus> on pcib2
pci1: <S3 Savage 4 graphics accelerator> at 0.0 irq 12
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA66 controller> port 0x9000-0x900f at device 7.1 on =
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x9400-0x941f irq 9 at device 7.2 o=
n pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0x9800-0x981f irq 9 at device 7.3 o=
n pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
chip2: <VIA 82C686 AC97 Audio> port 0xa400-0xa403,0xa000-0xa003,0x9c00-0x9c=
ff irq 11 at device 7.5 on pci0
atapci1: <Promise ATA100 controller> port 0xbc00-0xbc3f,0xb800-0xb803,0xb40=
0-0xb407,0xb000-0xb003,0xac00-0xac07 mem 0xdf100000-0xdf11ffff irq 11 at de=
vice 12.0 on pci0
ata2: at 0xac00 on atapci1
ata3: at 0xb400 on atapci1
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xc000-0xc03f mem 0xdf000000-0=
xdf0fffff,0xdf120000-0xdf120fff irq 10 at device 18.0 on pci0
fxp0: Ethernet address 00:d0:b7:c8:68:07
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
fdc0: direction bit not set
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x278-0x27f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 6204MB <ST36531A> [13446/15/63] at ata0-master UDMA33
ata1-master: DMA limited to UDMA33, non-ATA66 compliant cable
ad2: 8223MB <ST38410A> [16708/16/63] at ata1-master UDMA33
afd0: 239MB <IOMEGA ZIP 250 ATAPI> [239/64/32] at ata0-slave using PIO3
acd0: CD-RW <10X8X32> at ata1-slave using PIO4
Mounting root from ufs:/dev/ad0s1a
WARNING: / was not properly dismounted
--Multipart_Wed_May_23_18:02:52_2001-1
Content-Type: application/octet-stream
Content-Disposition: attachment; filename="KERNEL.CFG"
Content-Transfer-Encoding: quoted-printable
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246.2.25 2001/05/13 03:50:01 jlem=
on Exp $
machine i386
#cpu I386_CPU
#cpu I486_CPU
#cpu I586_CPU
cpu I686_CPU
ident GENERIC
maxusers 32
#makeoptions DEBUG=3D-g #Build kernel with gdb(1) debug symbols
#options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
#options MFS #Memory Filesystem
#options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
#options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
#options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=3D15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
#options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# To make an SMP kernel, the next two are needed
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
device isa
#device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
#options SYM_SETUP_LP_PROBE_MAP=3D0x40
# Allow ncr to attach legacy NCR devices when=20
# both sym and ncr are configured
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
#device ncv # NCR 53C500
#device nsp # Workbit Ninja SCSI-3
#device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers interfaced to the SCSI subsystem
#device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device dpt # DPT Smartcache - See LINT for options!
#device mly # Mylex AcceleRAID/eXtremeRAID
# RAID controllers
#device aac # Adaptec FSA RAID, Dell PERC2/PERC3
#device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
#device twe # 3ware Escalade
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT li=
nes
#options PCVT_SCANSET=3D2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# PCCARD (PCMCIA) support
#device card
#device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
#device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
#device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device tx # SMC 9432TX (83c170 ``EPIC'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
device wx # Intel Gigabit Ethernet Card (``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device pcn # AMD Am79C79x PCI 10/100 NICs
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS 7016
device ste # Sundance ST201 (D-Link DFE-550TX)
device tl # Texas Instruments ThunderLAN
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
device ex
device ep
device fe0 at isa? port 0x300
# Xircom Ethernet
device xe
# PRISM I IEEE 802.11b wireless NIC.
device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
device lnc0 at isa? port 0x280 irq 10 drq 0
device cs0 at isa? port 0x300
device sn0 at isa? port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
#pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
#pseudo-device bpf #Berkeley packet filter
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
#device usb # USB Bus (required)
#device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
#device uscanner # Scanners
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
--Multipart_Wed_May_23_18:02:52_2001-1--
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?87k838njdf.fsf>