Date: Thu, 25 Dec 1997 12:02:18 +0100 (MET) From: Dick van den Burg <burg@is.ge.com> To: Doug White <dwhite@resnet.uoregon.edu> Cc: Dick van den Burg <burg@perf.is.ge.com>, freebsd-questions@FreeBSD.ORG Subject: Re: How to add slice to existing FS Message-ID: <199712251102.MAA27710@burg.is.ge.com> In-Reply-To: <Pine.BSF.3.96.971224150623.10003W-100000@localhost> References: <199712230956.KAA14469@burg.is.ge.com> <Pine.BSF.3.96.971224150623.10003W-100000@localhost>
next in thread | previous in thread | raw e-mail | index | archive | help
Doug, Thanks very much. I used /stand/sysinstall to delete slice 4 and created the slice again as a freebsd partition. I then used the disklabel editor to create a new partition in the slice. When I tried to write the disklable sysinstall died with a segmentation fault. However I was able to newfs /dev/rsd0s4c. It probably is using the default disklabel, as I specified sd0s4e in the sysinstall disklabel. In retrospect I probably could have used fdisk to change the type of the slice to FBSD and the just do a newfs. In my case the FBSD slice that contains the root filesystem is before the new fs in slice 3. If this was not the case, would I be able to boot from the second slice of type 165? The boot prompt only allows a drive and a partition, not a slice. Thanks again ... Dick Doug White wrote: > On Tue, 23 Dec 1997, Dick van den Burg wrote: > > > I have the following slices: > > > > burg@vdb:~$ /sbin/fdisk sd0 > > ******* Working on device /dev/rsd0 ******* > > parameters extracted from in-core disklabel are: > > cylinders=1048 heads=127 sectors/track=63 (8001 blks/cyl) > > > > Figures below won't work with BIOS for partitions not in cyl 1 > > parameters to be used for BIOS calculations are: > > cylinders=1048 heads=127 sectors/track=63 (8001 blks/cyl) > > > > Media sector size is 512 > > Warning: BIOS sector numbering starts with sector 1 > > Information from DOS bootblock is: > > The data for partition 1 is: > > sysid 6,(Primary 'big' DOS (> 32MB)) > > start 63, size 1031562 (503 Meg), flag 80 > > beg: cyl 0/ sector 1/ head 1; > > end: cyl 128/ sector 63/ head 118 > > The data for partition 2 is: > > sysid 5,(Extended DOS) > > start 1032129, size 1024128 (500 Meg), flag 0 > > beg: cyl 129/ sector 1/ head 0; > > end: cyl 256/ sector 63/ head 126 > > The data for partition 3 is: > > sysid 165,(FreeBSD/NetBSD/386BSD) > > start 2056257, size 4800600 (2344 Meg), flag 0 > > beg: cyl 257/ sector 1/ head 0; > > end: cyl 856/ sector 63/ head 126 > > The data for partition 4 is: > > sysid 6,(Primary 'big' DOS (> 32MB)) > > start 6856857, size 1528191 (746 Meg), flag 0 > > beg: cyl 857/ sector 1/ head 0; > > end: cyl 1023/ sector 63/ head 126 > > > > I just reclaimed partition (=slice) 4 from a windows installation and > > I want to use the 746 Mb for a FreeBSD file system. As slice 3 already > > contains a FBSD installation I am at a loss on how to set up a > > disklabel such that newfs can set up a filesystem on partition 4. > > Very tricky. The bootloader can get confused in this instance. > > Basically: > > 1. Use DOS FDISK and delete the Primary DOS partition on slice 4. > 2. Use sysinstall to create a FreeBSD slice on slice 4. Partition as > desired. > 3. Newfs with care. > > > > > /usr/home/burg# /sbin/newfs /dev/rsd0s4c > > newfs: ioctl (GDINFO): Invalid argument > > newfs: /dev/rsd0s4c: can't read disk label; disk type must be specified > > See http://www.freebsd.org/tutorials/diskformat/ for a guide. I don't > detail how to do this specifically, but if you get a procedure that works > I'd like to add it. > > Doug White | University of Oregon > Internet: dwhite@resnet.uoregon.edu | Residence Networking Assistant > http://gladstone.uoregon.edu/~dwhite | Computer Science Major >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199712251102.MAA27710>