Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 25 Aug 2009 16:08:21 +0300
From:      Eugene Perevyazko <john@dnepro.net>
To:        freebsd-net@freebsd.org
Cc:        Pyun YongHyeon <pyunyh@gmail.com>
Subject:   Re: D-Link DGE-560SX (Marvell 88E8061-based) doesn't see link
Message-ID:  <20090825130821.GA41669@traktor.dnepro.net>
In-Reply-To: <20090825114649.GA11642@traktor.dnepro.net>
References:  <20090821142039.GA40018@traktor.dnepro.net> <20090821221932.GE1262@michelle.cdnetworks.com> <20090825083857.GA22983@traktor.dnepro.net> <20090825114649.GA11642@traktor.dnepro.net>

next in thread | previous in thread | raw e-mail | index | archive | help
Hello.

On Tue, Aug 25, 2009 at 02:46:49PM +0300, Eugene Perevyazko wrote:
> > > 
> > > ATM there is no easy/clean way to pass driver specific data to mii
> > > layer in FreeBSD so e1000phy(4) incorrectly thinks it found copper
> > > PHY. Marvell PHYs seem to have no reliable way to know configured
> > > media type of PHY hardware unless parent driver(msk) gives hint to
> > > it. If you have just 1 NIC which uses e1000phy(4) on your system,
> > > modify e1000phy(4) to force it having fiber media by inserting the
> > > following line around line 114 in e1000phy.c. 
> > > 
> > > sc->mii_flags |= MIIF_HAVEFIBER;
[...]
> --- e1000phy.c  2009-08-25 14:45:03.000000000 +0300
> +++ e1000phy.c.old      2009-08-25 14:44:47.000000000 +0300
> @@ -166,7 +166,6 @@
>                 break;
>         }
> 
> -       sc->mii_flags |= MIIF_HAVEFIBER;
>         e1000phy_reset(sc);
> 
>         sc->mii_capabilities = PHY_READ(sc, MII_BMSR) & ma->mii_capmask;
> 
> for src/sys/dev/mii/e1000phy.c,v 1.18.2.8

I've rebooted with new kernel with following results:

mskc0: <D-Link 560SX Gigabit Ethernet> port 0x4000-0x40ff mem 0xdc100000-0xdc103
fff irq 16 at device 0.0 on pci1
msk0: <Marvell Technology Group Ltd. Yukon XL Id 0xb3 Rev 0x03> on mskc0
msk0: Ethernet address: 00:21:91:52:4f:09
miibus1: <MII bus> on msk0
e1000phy0: <Marvell 88E1112 Gigabit PHY> PHY 0 on miibus1
e1000phy0:  1000baseSX, 1000baseSX-FDX, auto
mskc0: [FILTER]

# ifconfig msk0
msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4>
        ether 00:21:91:52:4f:09
        media: Ethernet autoselect

# ifconfig msk0 up
# ifconfig -m msk0
msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4>
        capabilities=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4>
        ether 00:21:91:52:4f:09
        media: Ethernet autoselect (autoselect <full-duplex>)
        status: active
        supported media:
                media autoselect
                media 1000baseSX mediaopt full-duplex
                media 1000baseSX
                media none

Switch and NIC see the link, but no packets pass through the interface.

# ifconfig msk0 media 1000baseSX mediaopt full-duplex
# ifconfig msk0
msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4>
        ether 00:21:91:52:4f:09
        media: Ethernet 1000baseSX <full-duplex> (autoselect <full-duplex>)
        status: active

Again no packets are seen with tcpdump.
Switch counters show no incoming packets from NIC if I set an ip and try to generate some traffic.

Any ideas?

-- 
Eugene Perevyazko



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20090825130821.GA41669>