Date: Wed, 18 Jun 2003 15:38:30 -0600 From: Brett Glass <brett@lariat.org> To: hardware@freebsd.org Subject: FreeBSD doesn't recognize onboard RTL8139 Message-ID: <4.3.2.7.2.20030618153536.033b6b40@localhost>
next in thread | raw e-mail | index | archive | help
I'm setting up FreeBSD on a little single-board computer with a built-in Realtek 8139 Ethernet controller. The board has a PCI slot, into which I've put a PCI card with another Realtek 8139. However, while FreeBSD recognizes the add-on card, it doesn't recognize the onboard chip. Here's a dmesg. I suspect that the line pci0: <unknown card> (vendor=0x1078, dev=0x0103) at 18.3 indicates that the onboard NIC was detected but not recognized. How do I fix this? --Brett Glass Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.8-RELEASE #0: Thu Apr 3 10:53:38 GMT 2003 root@freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Cyrix GXm (233.86-MHz 586-class CPU) Origin = "CyrixInstead" Id = 0x540 DIR=0x6346 Stepping=6 Revision=3 real memory = 268435456 (262144K bytes) avail memory = 255971328 (249972K bytes) Preloaded elf kernel "kernel" at 0xc051d000. md0: Malloc disk Using $PIR table, 4 entries at 0xc00fd9d0 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 rl0: <RealTek 8139 10/100BaseTX> port 0xe000-0xe07f mem 0xe4100000-0xe410007f irq 15 at device 7.0 on pci0 rl0: Ethernet address: 00:40:f6:b4:76:b1 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto pci0: <Intergraphics model 2010 VGA-compatible display device> at 9.0 irq 11 fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xe400-0xe41f mem 0xe4000000-0xe40fffff,0xe4101000-0xe4101fff irq 10 at device 10.0 on pci0 fxp0: Ethernet address 00:30:00:03:c8:06 inphy0: <i82555 10/100 media interface> on miibus1 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isab0: <Cyrix Cx5530 PCI-ISA bridge> at device 18.0 on pci0 isa0: <ISA bus> on isab0 chip1: <PCI to Other bridge (vendor=1078 device=0101)> mem 0x40012000-0x400120ff at device 18.1 on pci0 atapci0: <Cyrix 5530 ATA33 controller> port 0xf000-0xf00f at device 18.2 on pci0 pci0: <unknown card> (vendor=0x1078, dev=0x0103) at 18.3 orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0 fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 ata1 at port 0x170-0x177,0x376 irq 15 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ad0: 5729MB <FUJITSU MHK2060AT> [12416/15/63] at ata0-master BIOSPIO Mounting root from ufs:/dev/ad0s1a
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4.3.2.7.2.20030618153536.033b6b40>