Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 11 Jul 2006 23:57:49 +0400
From:      Michael <spampass@gmail.com>
To:        "John Baldwin" <jhb@freebsd.org>
Cc:        freebsd-amd64@freebsd.org
Subject:   Re: Turion 64 X2 support in future versions of FreeBSD.
Message-ID:  <93f8f44b0607111257j10923734i14309e1767abeb09@mail.gmail.com>
In-Reply-To: <200607111444.56287.jhb@freebsd.org>
References:  <93f8f44b0607061447k27adb556u306063b09b3d9b0d@mail.gmail.com> <44AEAC75.7010900@rogers.com> <93f8f44b0607110350o572c1c5ate3af435571908f3f@mail.gmail.com> <200607111444.56287.jhb@freebsd.org>

next in thread | previous in thread | raw e-mail | index | archive | help
On 11/07/06, John Baldwin <jhb@freebsd.org> wrote:
> > > Michael wrote:
> > > >
> > > > Thanks for advice! I've tried that, but no luck - absolutely the same
> > > > result. The reason why I was asking about *support* for that processor
> > > > is, that there is no mention for X2 in
> > > > http://www.freebsd.org/platforms/amd64.html. Only Turion 64, and no
> > > > X2. And personally I think, that things breaks because of second core
> > > > of CPU :-\
> > >
>
> I would really need to see the dmesg with ACPI enabled.  Also, when your
> machine is slow, have you checked to see if you have a high number of
> interrupts (via vmstat -i or systat -vmstat)?  Are there any extra messages
> in dmesg after boot once it is slow?   Can you get the output of 'sysctl
> hw.acpi' when it is slow?

Thanks for response!

================== dmesg ==================
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 6.1-RELEASE #0: Sun May  7 04:15:57 UTC 2006
    root@bloom.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
ACPI APIC Table: <A M I  OEMAPIC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-52 (1607.33-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x40f82  Stepping = 2
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x2001<SSE3,CX16>
  AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow+,3DNow>
  AMD Features2=0x1f<LAHF,CMP,<b2>,<b3>,CR8>
  Cores per package: 2
real memory  = 1073479680 (1023 MB)
avail memory = 1024225280 (976 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0 <Version 1.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <A M I OEMRSDT> on motherboard
acpi0: Power Button (fixed)
acpi_ec0: <Embedded Controller: GPE 0x20> port 0x62,0x66 on acpi0
acpi0: reservation of 62, 2 (4) failed
acpi0: reservation of 65, b (4) failed
acpi0: reservation of fec00000, 1000 (3) failed
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of e0000000, 10000000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x508-0x50b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.0 (no driver attached)
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
pci0: <memory, RAM> at device 0.6 (no driver attached)
pci0: <memory, RAM> at device 0.7 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <network, ethernet> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pci2: <display, VGA> at device 0.0 (no driver attached)
pci0: <memory, RAM> at device 9.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 10.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 10.1 (no driver attached)
pci0: <processor> at device 10.3 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xdcebe000-0xdcebefff irq
22 at device 11.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 8 ports with 8 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdcebfc00-0xdcebfcff
irq 23 at device 11.1 on pci0
ehci0: [GIANT-LOCKED]
usb1: EHCI version 1.0
usb1: companion controller, 8 ports each: usb0
usb1: <EHCI (generic) USB 2.0 controller> on ehci0
usb1: USB revision 2.0
uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 8 ports with 8 removable, self powered
ugen0: Syntek USB2.0, rev 2.00/0.05, addr 2
atapci0: <nVidia nForce MCP51 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 13.0 on
pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pcib3: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pci3: <ACPI PCI bus> on pcib3
cbb0: <RF5C476 PCI-CardBus Bridge> mem 0xdf800000-0xdf800fff irq 17 at
device 1.0 on pci3
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <Ricoh R5C552> mem 0xdf7ff000-0xdf7ff7ff irq 18 at device 1.1 on pci3
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:e0:18:00:03:5a:a9:a6
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:e0:18:5a:a9:a6
fwe0: Ethernet address: 02:e0:18:5a:a9:a6
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci3: <base peripheral> at device 1.2 (no driver attached)
pci3: <base peripheral> at device 1.3 (no driver attached)
pci3: <network> at device 3.0 (no driver attached)
pci0: <multimedia> at device 16.1 (no driver attached)
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button1: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
ppc0: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
ugen1: vendor 0x0b05 product 0x1712, rev 2.00/19.15, addr 3
Timecounters tick every 1.000 msec
module_register_init: MOD_LOAD (amr_linux, 0xffffffff8062a040, 0) error 6
acd0: DVDR <TSSTcorpCD/DVDW TS-L632D/AS04> at ata0-master UDMA33
ad2: 95396MB <HTS541010G9AT00 MBZOA60A> at ata1-master UDMA100
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad2s2a

================== vmstat -i ==================
interrupt                          total       rate
irq1: atkbd0                         457          3
irq9: acpi0                           30          0
irq14: ata0                           47          0
irq15: ata1                          768          5
irq18: fwohci0                         1          0
irq22: ohci0                        3810         25
irq23: ehci0                           2          0
cpu0: timer                        19005        129
cpu1: timer                         9016         61
Total                              33136        225

================== sysctl hw.acpi ==================
hw.acpi.supported_sleep_state: S1 S3 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S1
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: S3
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 0
hw.acpi.verbose: 0
hw.acpi.cpu.cx_supported: C1/0
hw.acpi.cpu.cx_lowest: C1
hw.acpi.cpu.cx_usage: 100.00%
hw.acpi.thermal.min_runtime: 0
hw.acpi.thermal.polling_rate: 10
hw.acpi.thermal.tz0.temperature: 70.0C
hw.acpi.thermal.tz0.active: -1
hw.acpi.thermal.tz0.passive_cooling: 0
hw.acpi.thermal.tz0.thermal_flags: 0
hw.acpi.thermal.tz0._PSV: -1
hw.acpi.thermal.tz0._HOT: -1
hw.acpi.thermal.tz0._CRT: 110.0C
hw.acpi.thermal.tz0._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.battery.life: 99
hw.acpi.battery.time: -1
hw.acpi.battery.state: 0
hw.acpi.battery.units: 1
hw.acpi.battery.info_expire: 5
hw.acpi.acline: 1



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?93f8f44b0607111257j10923734i14309e1767abeb09>