Date: Sun, 27 Aug 1995 21:50:17 -0500 (CDT) From: R Robert Willman <willmann@texas.net> To: hackers@FreeBSD.org Subject: FreeBSD 2.0.5 Message-ID: <Pine.SUN.3.91.950827211206.20427A-100000@millenium.texas.net>
next in thread | raw e-mail | index | archive | help
I have run into 3 current problems when installing 2.0.5. 1. After trying to change the path and doing so in a session, when I shutdown the system and restarted it, the changes to the path were gone and were not saved. I added /usr/X11R6/bin to the path. Also, I set umask to 022. I made these changes to try to set up X11R6 that came with your CD-rom. Whether I shutdown and halted the system and rebooted it, or shut it down, halted it, turned it off, and turned it back on, the attempted changes made using "set" were not saved and I would have to do them each time I logged in. 2. After I loaded the system and rebooted it, and then shut it down, halted it, and rebooted it, or did a shutdown and halt and turned the system off and then on, unless I had the CD-rom drive on and the disk in it, the system would not finish booting properly. This would happen if I turned off the computer entirely, turned off the CD-rom drive, removed it from the SCSI port, and put a SCSI terminator on the port at the back of the computer, and then turned the computer back on and booted it up. This is what the screen said at the end of the booting sequence: Automatic reboot in progress /dev/rsd0a: clean, 7659 free (107 frags, 944 blocks, 0.5% fragmentation) /dev/rsd0sle: clean, 271946 free (10354 frags, 32699 blocks, 3.1% fragmentation) cd9660: /dev/cd0a: Device not configured Filesystem mount failed, startup aborted Enter pathname of shell or RETURN for sh: If I had the CD-rom drive plugged into the computer, turned on, and had the disk in it, the booting would complete properly and I would be at a login in which I would put root and get into a C shell. 3. The X window system comes up but the screen is badly distorted, like it is made of tweed. I can see the three windows with red bars at the top, and that there is a clock in the upper right hand corner, but nothing can be read. It is not fuzzy, it is tweeded-out all over, including in the windows, as one mess. If I click the mouse in the background, the menu comes up, and it will show highlighted words as the pointer is pulled down, but the words cannot be read--they are too distorted. When I cycle through the resolutions (4 of them), using cntr-alt-numpad+, the size of the screen and windows change as each should. I have checked the config file and the settings for the S3 chipset. My system is described below. I have a 486DX4/100 (AMD chip) on an Asus motherboard, 24 mb ram, an Adaptec 2842 SCSI host bus adapter, a Diamond Stealth 64 VRAM graphics adapter, a Quantum SCSI hard drive, and a Radius PrecisionColor Display/17 monitor. And a regular 3.5 inch floppy. I put the horizontal and vertical frequencies from the Radius spec sheet into the config file for X11R6. On the hard drive I have a Novell Dos 7 partition and a Nextstep ver. 3.3 partition. I am trying to put Free BSD on the rest of the hard disk. Sincerely, Robert Willmann, Jr. willmann@texasnet 210-224-8866 San Antonio, Texas
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.SUN.3.91.950827211206.20427A-100000>