Date: Sun, 7 Dec 2003 12:36:35 -0500 (EST) From: "Judd Storrs" <storrsjm@email.uc.edu> To: <freebsd-firewire@freebsd.org> Subject: Sony DRX-510UL CD/DVD burner: probe failed for 1 node Message-ID: <49736.172.22.77.20.1070818595.squirrel@storrs.net>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Hello,
Great work on the firewire support in freebsd, I recently started to use
an external firewire hard drive to expand my laptop and it is awesome!
I've been able to build -current and ports while conserving disk space in
the laptop. It's very liberating. Thanks!
I am having trouble with a Sony firewire DVD burner though, has anybody
had success with the Sony DRX-510UL DVD+/-R/RW drive using
firewire/i.LINK? I'm now running current from 12/06/2003 with aio kernel
module. [The drive isn't listed by fwcontrol without aio.] When I plug the
drive I observe the following in dmesg (with aio.ko loaded/full dmesg
attached):
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc1, gen=3, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc1, gen=4, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
firewire0: New S400 device ID:080046090009e518
firewire0: split transaction timeout dst=0xffc0 tl=0xa state=3
node0: resp=60 addr=0x418
probe failed for 1 node
fwcontrol reports:
2 devices (info_len=2)
node EUI64 status
1 0x0800285602000333 0
-1 0x080046090009e518 0
[0x0800285602000333 = Adaptec DuoConnect PCIMCIA firewire/usb2]
My kernel is a slightly modified GENERIC: I686 only without INVARIANTS and
without WITNESS. Full dmesg attached. The Adaptec card works with a
firewire harddrive, and I can use the DVD drive over usb1 (usb2 does not
work for the Adaptec card: adding ehci to my kernel results in panics when
the card is inserted). Any suggestions?
Thanks,
--judd
[-- Attachment #2 --]
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-BETA #1: Sun Dec 7 00:22:06 EST 2003
root@anubis.storrs.net:/mnt/anubis/obj/mnt/anubis/src/sys/ANUBIS
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a9b000.
Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0a9b1cc.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a9b278.
Preloaded acpi_dsdt "/boot/acpi_dell_dsdt.aml" at 0xc0a9b324.
Preloaded elf module "/boot/kernel/aio.ko" at 0xc0a9b374.
Preloaded elf module "/boot/kernel/speaker.ko" at 0xc0a9b41c.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) III Mobile CPU 1000MHz (996.79-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 268251136 (255 MB)
avail memory = 250916864 (239 MB)
Pentium Pro MTRR support enabled
ACPI: DSDT was overridden.
ACPI-0375: *** Info: Table [DSDT] replaced by host OS
acpi0: <DELL CPi R > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 11 entries at 0xc00fbb90
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 29 INTA is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
agp0: <Intel 82830 host to AGP bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 11
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib2: slot 0 INTA is routed to irq 11
pcib2: slot 3 INTA is routed to irq 11
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec80-0xecff mem 0xf8fffc00-0xf8fffc7f irq 11 at device 0.0 on pci2
xl0: Ethernet address: 00:06:5b:31:4b:92
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: <TI1420 PCI-CardBus Bridge> at device 1.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: slot 1 INTA is routed to irq 11
cbb0: [MPSAFE]
cbb1: <TI1420 PCI-CardBus Bridge> at device 1.1 on pci2
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib2: slot 1 INTA is routed to irq 11
cbb1: [MPSAFE]
cbb2: <TI1410 PCI-CardBus Bridge> irq 11 at device 3.0 on pci2
cardbus2: <CardBus bus> on cbb2
pccard2: <16-bit PCCard bus> on cbb2
cbb2: [MPSAFE]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0xbfa0-0xbfaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pcm0: <Intel ICH3 (82801CA)> port 0xdc80-0xdcbf,0xd800-0xd8ff irq 11 at device 31.5 on pci0
pcm0: <Cirrus Logic CS4205 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
speaker0 port 0x67,0x65,0x63,0x61 on acpi0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x270-0x277,0x3f8-0x3ff irq 4 drq 3 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 996786998 Hz quality 800
Timecounters tick every 10.000 msec
wi0: <Dell TrueMobile 1150 Series PC Card> at port 0x100-0x13f irq 11 function 0 config 1 on pccard2
wi0: 802.11 address: 00:02:2d:81:3a:4b
wi0: using Lucent Embedded WaveLAN/IEEE
wi0: Lucent Firmware: Station (8.72.1)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
GEOM: create disk ad0 dp=0xc2e5f760
ad0: 19077MB <HITACHI_DK23CA-20> [38760/16/63] at ata0-master UDMA100
acd0: CDROM <SAMSUNG CD-ROM SN-124> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s3a
cardbus1: Resource not specified in CIS: id=10, size=800
cardbus1: Resource not specified in CIS: id=14, size=4000
fwohci0: <Texas Instruments TSB43AB23> mem 0xf4004000-0xf4007fff,0xf4008000-0xf40087ff irq 11 at device 0.0 on cardbus1
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 08:00:28:56:02:00:03:33
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 0a:00:28:00:03:33
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
cardbus1: Resource not specified in CIS: id=10, size=1000
ohci0: <NEC uPD 9210 USB controller> mem 0xf4004000-0xf4004fff irq 11 at device 0.4 on cardbus1
usb1: OHCI version 15.15, legacy support
usb1: unsupported OHCI revision
ohci0: USB init failed
device_probe_and_attach: ohci0 attach returned 5
cardbus1: Resource not specified in CIS: id=10, size=1000
ohci0: <NEC uPD 9210 USB controller> mem 0xf4004000-0xf4004fff irq 11 at device 0.5 on cardbus1
usb1: OHCI version 15.15, legacy support
usb1: unsupported OHCI revision
ohci0: USB init failed
device_probe_and_attach: ohci0 attach returned 5
cardbus1: Resource not specified in CIS: id=10, size=100
cardbus1: <serial bus, USB> at device 0.6 (no driver attached)
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc1, gen=3, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc1, gen=4, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
firewire0: New S400 device ID:080046090009e518
firewire0: split transaction timeout dst=0xffc0 tl=0xa state=3
node0: resp=60 addr=0x418
probe failed for 1 node
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?49736.172.22.77.20.1070818595.squirrel>