Date: Sun, 21 Mar 2004 09:15:00 +0000 From: Mark Dixon <mark@markdnet.demon.co.uk> To: freebsd-scsi@freebsd.org Subject: Adaptec 19160 and SCA-80 drive Message-ID: <200403210915.16226.mark@markdnet.demon.co.uk>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --] Hi, I've got an Adaptec 19160 and I have connected it to a 9gb SCA-80 drive via an adaptor which converts it to a 50 pin SCSI device. This works well in Debian Linux, and grudgingly in Windows (it seems to take a few seconds longer than it should to figure out whats going on), but FreeBSD really doesn't like it. With Parity on, FreeBSD refuses to boot claiming parity errors on all SCSI ids on the board (despite there being only one disk attached). It then locks up attempting to destroy the disk (I presume it doesn't mean that literally). With parity off in dmesg, I get: GEOM: create disk da0 dp=0xc3b7b450 da0 at ahc0 bus 0 target 0 lun 0 da0: <SEAGATE ST19171W 2219> Fixed Direct Access SCSI-2 device da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled da0: 8203MB (16800001 512 byte sectors: 255H 63S/T 1045C) which looks good. Unfortunately, attempting to do anything with the disk, results in the following: lizacnet# bsdlabel -w /dev/da0 bsdlabel: write /dev/da0: Input/output error (da0:ahc0:0:0:0): WRITE(06). CDB: a 0 0 0 10 0 (da0:ahc0:0:0:0): CAM Status: SCSI Status Error (da0:ahc0:0:0:0): SCSI Status: Check Condition (da0:ahc0:0:0:0): ABORTED COMMAND asc:0,0 (da0:ahc0:0:0:0): No additional sense information (da0:ahc0:0:0:0): Retrying Command (per Sense Data) (da0:ahc0:0:0:0): WRITE(06). CDB: a 0 0 0 10 0 (da0:ahc0:0:0:0): CAM Status: SCSI Status Error (da0:ahc0:0:0:0): SCSI Status: Check Condition (da0:ahc0:0:0:0): ABORTED COMMAND asc:0,0 (da0:ahc0:0:0:0): No additional sense information (da0:ahc0:0:0:0): Retrying Command (per Sense Data) (da0:ahc0:0:0:0): WRITE(06). CDB: a 0 0 0 10 0 (da0:ahc0:0:0:0): CAM Status: SCSI Status Error (da0:ahc0:0:0:0): SCSI Status: Check Condition (da0:ahc0:0:0:0): ABORTED COMMAND asc:0,0 (da0:ahc0:0:0:0): No additional sense information (da0:ahc0:0:0:0): Retrying Command (per Sense Data) (da0:ahc0:0:0:0): WRITE(06). CDB: a 0 0 0 10 0 (da0:ahc0:0:0:0): CAM Status: SCSI Status Error (da0:ahc0:0:0:0): SCSI Status: Check Condition (da0:ahc0:0:0:0): ABORTED COMMAND asc:0,0 (da0:ahc0:0:0:0): No additional sense information (da0:ahc0:0:0:0): Retrying Command (per Sense Data) (da0:ahc0:0:0:0): WRITE(06). CDB: a 0 0 0 10 0 (da0:ahc0:0:0:0): CAM Status: SCSI Status Error (da0:ahc0:0:0:0): SCSI Status: Check Condition (da0:ahc0:0:0:0): ABORTED COMMAND asc:0,0 (da0:ahc0:0:0:0): No additional sense information (da0:ahc0:0:0:0): Retries Exhausted Setting kern.geom.debugflags -> 1 gives: g_post_event_x(0xc04ac530, 0xc39fa080, 2) ref 0xc39fa080 mbr_taste(MBR,da0) g_slice_config(da0, 0, 0) g_slice_config(da0, 1, 0) g_slice_config(da0, 2, 0) g_slice_config(da0, 3, 0) g_slice_config(da0, 0, 1) g_post_event_x(0xc04ac530, 0xc3caf700, 2) ref 0xc3caf700 g_slice_config(da0, 1, 1) g_slice_config(da0, 2, 1) g_slice_config(da0, 3, 1) bsd_taste(BSD,da0) g_slice_spoiled(0xc473fe00/da0) g_wither_geom(0xc3bacb80(da0)) g_detach(0xc473fe00) g_destroy_consumer(0xc473fe00) g_destroy_geom(0xc3bacb80(da0)) g_mbrext_taste(MBREXT,da0) mbr_taste(MBR,da0s1) g_slice_spoiled(0xc473f300/da0s1) g_wither_geom(0xc3d6d680(da0s1)) g_detach(0xc473f300) g_destroy_consumer(0xc473f300) g_destroy_geom(0xc3d6d680(da0s1)) bsd_taste(BSD,da0s1) g_slice_spoiled(0xc439d940/da0s1) g_wither_geom(0xc41e5d00(da0s1)) g_detach(0xc439d940) g_destroy_consumer(0xc439d940) g_destroy_geom(0xc41e5d00(da0s1)) dev_taste(DEV,da0s1) g_mbrext_taste(MBREXT,da0s1) g_slice_spoiled(0xc473f4c0/da0s1) g_wither_geom(0xc41e5100(da0s1)) g_detach(0xc473f4c0) g_destroy_consumer(0xc473f4c0) g_destroy_geom(0xc41e5100(da0s1)) ahc and ahc_pci are loaded as modules, if that makes any difference. I did try loading debug versions of the modules and I think I got a panic, but I was in X at the time and there was no sign of it on reboot. Any ideas whats up? -- Mark 'If it compiles, ship it' [-- Attachment #2 --] -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (FreeBSD) iD8DBQBAXV0kLqgJ90OcaiARAoi4AKCHItbESR3r3w8ljp+zvNGWTCTHDwCeI4Fo +faA4BNbgv/4yhIVWZpg86Y= =S+UW -----END PGP SIGNATURE-----
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200403210915.16226.mark>