Date: Sun, 8 Dec 2002 17:52:35 +0900 (JST) From: nao <nao@tom-yam.or.jp> To: freebsd-firewire@freebsd.org Subject: ATA HDD via FireWire failes. Message-ID: <200212080852.gB88qZZg000595@miffy.tom-yam.or.jp>
next in thread | raw e-mail | index | archive | help
Hello, guys! I tried Mathey MIFU-25CB11 2.5 inch HDD case with my FreeBSD-stable box. This case uses FireUSB-1 SBP-II chip (http://www.aska-corp.co.jp/z_fireusb.html), which converts ATA interface to IEEE1394 and USB-1.1. As follows, it was not attached: Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.7-STABLE #14: Sun Dec 8 15:58:34 JST 2002 root@miffy.tom-yam.or.jp:/usr/obj/usr/src/sys/ZAZIE Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (1312.93-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 268349440 (262060K bytes) config> di fdc0 config> q avail memory = 257658880 (251620K bytes) Preloaded elf kernel "kernel" at 0xc036b000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc036b09c. Preloaded elf module "ipfw.ko" at 0xc036b0ec. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 11 entries at 0xc00f13a0 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pcib1: <Intel 82801BA/BAM (ICH2) PCI-PCI (AGP) bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0 pci2: <PCI bus> on pcib2 pci2: <Matrox MGA 1024SG/1064SG/1164SG graphics accelerator> at 9.0 irq 4 fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xd800-0xd81f mem 0xf4000000-0xf40fffff,0xf6000000-0xf6000fff irq 3 at device 10.0 on pci2 fxp0: Ethernet address 00:a0:c9:24:5e:46 nsphy0: <DP83840 10/100 media interface> on miibus0 nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0xd400-0xd43f mem 0xf3000000-0xf30fffff,0xf3800000-0xf3800fff irq 5 at device 11.0 on pci2 fxp1: Ethernet address 00:90:27:57:64:1b inphy0: <i82555 10/100 media interface> on miibus1 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fwohci0: <VIA VT6306> port 0xd000-0xd07f mem 0xf2800000-0xf28007ff irq 12 at device 12.0 on pci2 fwohci0: PCI bus latency was changing to 250. cache size 8. fwohci0: OHCI version 1.0 (ROM=1) fwohci0: No. of Isochronous channel is 8. fwohci0: resetting OHCI...done (0) fwohci0: BUS_OPT 0xf800a202 -> 0xf800a202 fwohci0: Link 1394a available S400, 3 ports, maxrec 2048 bytes. fwohci0: Enable 1394a Enhancements fwohci0: EUI64 00:11:06:00:bc:00:4f:d0 fwochi_set_intr: 1 firewire0: <IEEE1394(Firewire) bus> on fwohci0 firewire0: firewire bus attach if_fwe0: <Ethernet over Firewire> on firewire0 if_fwe0: 02:11:06:00:4f:d0 sbp_identify sbp_probe sbp0: <SBP2/SCSI over firewire> on firewire0 sbp_attach isab0: <Intel 82801BA/BAM (ICH2) PCI to LPC bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH2 ATA100 controller> port 0xb800-0xb80f at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> at 31.2 irq 10 pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 11 pci0: <Intel 82801BA/BAM (ICH2) USB controller USB-B> at 31.4 irq 5 orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 firewire0: BUS reset firewire0: node_id = 0xc800ffc0, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) fw_set_bus_manager: 63->0 (loop=0) send phy_config root_node=-1 gap_count=1 start AT DMA status=0 IP packet filtering initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled ad0: 39083MB <Accusys ACS7500 C5VL> [79408/16/63] at ata0-master UDMA100 acd0: CD-RW <428 CDRW> at ata1-slave PIO3 bus_explore done Mounting root from ufs:/dev/ad0s1a cd0 at ata1 bus 0 target 1 lun 0 cd0: <PHILIPS 428 CDRW 2.0D> Removable CD-ROM SCSI-0 device cd0: 11.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed firewire0: BUS reset firewire0: node_id = 0x8800ffc0, non CYCLEMASTER mode firewire0: 2 nodes, maxhop <= 1, cable IRM = 0 (me) fw_set_bus_manager: 63->0 (loop=0) send phy_config root_node=-1 gap_count=1 start AT DMA status=11 firewire0: BUS reset firewire0: txd err= f flushed fw_xfer_done: pending firewire0: txd err= f flushed fw_xfer_done: pending firewire0: node_id = 0xc800ffc1, CYCLEMASTER mode firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me) fw_set_bus_manager: 63->1 (loop=0) send phy_config root_node=-1 gap_count=1 start AT DMA status=f firewire0:Discover new S400 device ID:0001d2400e080b06 bus_explore done Device SBP-II sbp_post_explore: EUI:0001d2400e080b06 spec=1 key=1. sbp0:0:0 LOGIN sbp0:0:0 ordered:1 type:14 EUI:0001d2400e080b06 node:0 speed:2 maxrec:10 new! sbp0:0:0 'Macpower' 'FRUB3W' '000114' resp != 0: node=2 addr=0x400 fw_attach_dev: 2 pending handlers called retry_count = 1 sbp0:0:0 login: len 16, ID 1, cmd 0000fffff0010000, recon_hold 0 sbp0:0:0 sbp_busy_timeout sbp0:0:0 sbp_agent_reset sbp0:0:0 sbp_do_attach sbp0:0:0 sbp_cam_scan_lun sbp0:0:0 ORB status src:1 resp:0 dead:0 len:3 stat:9 orb:00001a3a4 sbp0:0:0 Function rejected sbp0:0:0 XPT_SCSI_IO: cmd: 12 01 80 00 ff 00 00 00 00 00, flags: 0x40, 6b cmd/255b data/18b sense sbp0:0:0 SCSI status 2 sfmt 0 valid 0 key 5 code 24 qlfr 0 len 3 sbp0:0:0 ORB status src:1 resp:0 dead:0 len:3 stat:9 orb:00001a4d8 sbp0:0:0 Function rejected sbp0:0:0 XPT_SCSI_IO: cmd: 00 00 00 00 00 00 00 00 00 00, flags: 0xc0, 6b cmd/0b data/32b sense sbp0:0:0 SCSI status 2 sfmt 0 valid 0 key 6 code 29 qlfr 0 len 3 firewire0: BUS reset firewire0: node_id = 0xc800ffc1, CYCLEMASTER mode firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me) fw_set_bus_manager: 63->1 (loop=0) send phy_config root_node=-1 gap_count=1 start AT DMA status=f bus_explore done sbp_post_explore: EUI:0001d2400e080b06 spec=1 key=1. sbp0:0:0 RECONNECT sbp0:0:0 ordered:1 type:14 EUI:0001d2400e080b06 node:0 speed:2 maxrec:10 sbp0:0:0 'Macpower' 'FRUB3W' '000114' sbp0:0:0 reconnect: len 16, ID 1, cmd 0000fffff0010000 Any idea? -nao To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-firewire" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200212080852.gB88qZZg000595>