Date: Sun, 26 Feb 2006 15:16:51 +0000 From: Pete Carss <itinerant@mac.com> To: freebsd-ppc@freebsd.org Subject: [Fwd: Pismo Success] Message-ID: <4401C663.5030908@mac.com>
next in thread | raw e-mail | index | archive | help
Hello All I have successfully installed 7.0-20051105-SNAP on a 400Mhz G3 Pismo. I had to setup a local ftp server to get around the lack of CD drive. I also tried an external firewire drive with no success. I left a 32Mb hfs+ partition, which I mounted on another mac, by putting the Pismo into target disk mode, then copied loader over. then... setenv boot-device hd:loader hd:11 reset-all in OpenFirmware and I've got FreeBSD on a laptop. Where should I start hacking to get ADB support? What's the status of power management? I got a few instant offs when I unplugged from the mains... Thanks for the work Pete Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 7.0-20051105-SNAP #0: Sat Nov 5 04:33:52 UTC 2005 root@macmini.ptree32.com.au:/usr/obj/usr/src/sys/GENERIC Timecounter "decrementer" frequency 24966218 Hz quality 0 cpu0: Motorola PowerPC 750 revision 2.2, 400.00 MHz cpu0: HID0 8090c0a4<EMCP,DOZE,DPM,ICE,DCE,SGE,BTIC,BHT> real memory = 125362176 (119 MB) avail memory = 119640064 (114 MB) nexus0: <Open Firmware Nexus device> openpic0: <OpenPIC Interrupt Controller> on nexus0 unin0: <Apple UniNorth System Controller> on nexus0 unin0: Version 8 pcib0: <Apple UniNorth Host-PCI bridge> on nexus0 pci0: <PCI bus> on pcib0 pci0: <display, VGA> at device 16.0 (no driver attached) pcib1: <Apple UniNorth Host-PCI bridge> on nexus0 pci1: <PCI bus> on pcib1 macio0: <KeyLargo I/O Controller> mem 0x80000000-0x8007ffff at device 23.0 on pci1 zs0: <Zilog Z8530> mem 0x13000-0x13fff,0x8400-0x84ff,0x8500-0x85ff,0x8600-0x86ff,0x8700-0x87ff irq 22,23 on macio0 zs0: [FAST] zs0: [FAST] zstty0 on zs0 zstty1 on zs0 ata0 mem 0x1f000-0x1ffff,0x8a00-0x8aff irq 19 on macio0 ata1 mem 0x21000-0x21fff,0x8c00-0x8cff irq 21 on macio0 ohci0: <Apple KeyLargo USB controller> mem 0xa0002000-0xa0002fff irq 27 at device 24.0 on pci1 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0 usb0: <Apple KeyLargo USB controller> on ohci0 usb0: USB revision 1.0 uhub0: Apple OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ohci1: <Apple KeyLargo USB controller> mem 0xa0001000-0xa0001fff irq 28 at device 25.0 on pci1 ohci1: [GIANT-LOCKED] usb1: OHCI version 1.0 usb1: <Apple KeyLargo USB controller> on ohci1 usb1: USB revision 1.0 uhub1: Apple OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci1: <bridge, PCI-CardBus> at device 26.0 (no driver attached) pcib2: <Apple UniNorth Host-PCI bridge> on nexus0 pci2: <PCI bus> on pcib2 fwohci0: <1394 Open Host Controller Interface> mem 0xf5000000-0xf5000fff irq 40 at device 14.0 on pci2 fwohci0: OHCI version 1.0 (ROM=0) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:30:65:ff:fe:bf:ba:44 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:30:65:bf:ba:44 fwe0: Ethernet address: 02:30:65:bf:ba:44 fwe0: if_start running deferred for Giant fwohci0: Initiate bus reset resCount = 4080 !? fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode plen(-4060) is negative! offset=4080 firewire0: 1 nodes, maxhop <= 0, Not found IRM capable node gem0: <Apple GMAC Ethernet Adaptor> mem 0xf5200000-0xf53fffff irq 41 at device 15.0 on pci2 miibus0: <MII bus> on gem0 bmtphy0: <BCM5201 10/100baseTX PHY> on miibus0 bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto gem0: 10kB RX FIFO, 4kB TX FIFO gem0: Ethernet address: 00:30:65:bf:ba:44 sc0: <System console> on nexus0 sc0: Unknown <16 virtual consoles, flags=0x300> uhub2: vendor 0x0409 product 0x55ab, class 9/0, rev 1.00/1.00, addr 2 uhub2: 4 ports with 4 removable, bus powered ukbd0: Alps Electric M2452, rev 1.00/1.01, addr 3, iclass 3/1 Timecounters tick every 10.000 msec ad0: 9590MB <TOSHIBA MK1016GAP U1.13 A> at ata0-master BIOSPIO Trying to mount root from ufs:/dev/ad0s11
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4401C663.5030908>