Date: Mon, 3 Oct 2016 08:41:33 +0900 (JST) From: Mori Hiroki <yamori813@yahoo.co.jp> To: "freebsd-mips@freebsd.org" <freebsd-mips@freebsd.org> Subject: Re: Solve: AR7161 USB Message-ID: <262371.61155.qm@web101715.mail.ssk.yahoo.co.jp> In-Reply-To: <CAJ-Vmo=QgER78Wpn6Q4rPa=v8pEF7U-pBWNaZcLm3bdP3vTCrA@mail.gmail.com> References: <379174.95890.qm@web101716.mail.ssk.yahoo.co.jp> <063ff05f-d464-823a-495c-abb800dfdaf5@freebsd.org> <105245.8987.qm@web101701.mail.ssk.yahoo.co.jp> <CAJ-VmokSNP%2BZr5s14TzvkNMukLHRFEK9p2jEpfjB=X5N4u1=Sw@mail.gmail.com> <181104.30133.qm@web101710.mail.ssk.yahoo.co.jp> <CAJ-Vmo=QgER78Wpn6Q4rPa=v8pEF7U-pBWNaZcLm3bdP3vTCrA@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi.=0A=0AI add this setting to rc script to=A0WZR-HP-AG300H at=A0ZRouter=0A= build system.=0A=0AI think sys/mips/conf have only soc base setting. Becaus= e of=0Asoc and board setting is very scrambled. It is hard find target=0Ase= tting. We are never correct all world board setting.=0A=0ARegards=0A=0AHiro= ki Mori=0A=0A=0A----- Original Message -----=0A> From: Adrian Chadd <adrian= .chadd@gmail.com>=0A> To: Mori Hiroki <yamori813@yahoo.co.jp>=0A> Cc: "free= bsd-mips@freebsd.org" <freebsd-mips@freebsd.org>=0A> Date: 2016/9/30, Fri 0= 6:41=0A> Subject: Re: Solve: AR7161 USB=0A> =0A> Cool. There's some stuff y= ou can put in hints to set on/off gpio=0A> functions. Can you provide a dif= f to the right .hints file so it's=0A> done at boot time?=0A> =0A> =0A> -ad= rian=0A> =0A> On 28 September 2016 at 23:46, Mori Hiroki <yamori813@yahoo.c= o.jp> wrote:=0A>> Hi=0A>> =0A>> Thanks for your advice. I can use USB on = AR7161.=0A>> =0A>> # gpioctl 2 1=0A>> # usbconfig=0A>> =0A>> ugen0.1: <O= HCI root HUB Atheros> at usbus0, cfg=3D0 md=3DHOST spd=3DFULL =0A> (12Mbps)= pwr=3D=0A>> SAVE (0mA)=0A>> ugen1.1: <EHCI root HUB Atheros> at usbus1, = cfg=3D0 md=3DHOST spd=3DHIGH =0A> (480Mbps) pwr=0A>> =3DSAVE (0mA)=0A>> u= gen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, cfg=3D0 md=3DHOST = =0A> spd=3DFULL (=0A>> 12Mbps) pwr=3DON (100mA)=0A>> =0A>> Thanks.=0A>> = =0A>> Hiroki Mori=0A>> =0A>> ----- Original Message -----=0A>>> From: Ad= rian Chadd <adrian.chadd@gmail.com>=0A>>> To: Mori Hiroki <yamori813@yahoo= .co.jp>=0A>>> Cc: "freebsd-mips@freebsd.org" =0A> <freebsd-mips@freebsd.or= g>=0A>>> Date: 2016/9/29, Thu 13:21=0A>>> Subject: Re: AR7161 USB=0A>>> = =0A>>> it could be something to do with port or phy power. check the defau= lt=0A>>> gpio settings for your board; some don't enable usb phy power.=0A= >>> =0A>>> =0A>>> -a=0A>>> =0A>>> =0A>>> On 28 September 2016 at 20:51, M= ori Hiroki =0A> <yamori813@yahoo.co.jp> wrote:=0A>>>> =A0 Hi.=0A>>>> =0A>>>= > =A0 on WZR-HP-G300NH(AR9132) OK=0A>>>> =0A>>>> =0A>>>> =0A>>>> =A0 # usbc= onfig=0A>>>> =A0 ugen0.1: <EHCI root HUB Atheros> at usbus0, cfg=3D0 md=3DH= OST =0A> spd=3DHIGH=0A>>> (480Mbps) pwr=0A>>>> =A0 =3DSAVE (0mA)=0A>>>> = =A0 ugen0.2: <USB IR REMOCON Bit Trade One LTD.> at usbus0, =0A> cfg=3D0 md= =3DHOST=0A>>> spd=3DFULL (=0A>>>> =A0 12Mbps) pwr=3DON (100mA)=0A>>>> =A0 = #=0A>>>> =0A>>>> =0A>>>> =A0 on WZR-HP-AG300H(AR7161) NG=0A>>>> =0A>>>> =A0= # usbconfig=0A>>>> =A0 ugen0.1: <OHCI root HUB Atheros> at usbus0, cfg=3D0= md=3DHOST =0A> spd=3DFULL=0A>>> (12Mbps) pwr=3D=0A>>>> =A0 SAVE (0mA)=0A>= >>> =A0 ugen1.1: <EHCI root HUB Atheros> at usbus1, cfg=3D0 md=3DHOST =0A> = spd=3DHIGH=0A>>> (480Mbps) pwr=0A>>>> =A0 =3DSAVE (0mA)=0A>>>> =0A>>>> =A0= I use ZRouter on build. I check hints file. I seem same as=0A>>>> =A0 sys/= mips/conf/AP96.hints.=0A>>>> =0A>>>> =A0 Thanks=0A>>>> =0A>>>> =A0 Hiroki M= ori=0A>>>> =0A>>>> =0A>>>> =0A>>>> =A0 ----- Original Message -----=0A>>>>>= =A0 From: Sean Bruno <sbruno@freebsd.org>=0A>>>>> =A0 To: freebsd-mips@fre= ebsd.org=0A>>>>> =A0 Cc:=0A>>>>> =A0 Date: 2016/9/27, Tue 23:10=0A>>>>> =A0= Subject: Re: AR7161 USB=0A>>>>> =0A>>>>> =0A>>>>> =0A>>>>> =A0 On 09/27/16= 04:02, Mori Hiroki wrote:=0A>>>>>> =A0 Hi.=0A>>>>>> =0A>>>>>> =A0 I try = to use AR7161 target(WZR-HP-AG300H) on head today.=0A>>>>>> =A0 But I can'= t use USB this target. Device is probe on =0A> boot but=0A>>> USB device= =0A>>>>>> =A0 insert not detect device.=0A>>>>>> =0A>>>>>> =A0 Any one us= e this ?=0A>>>>>> =0A>>>>>> =A0 Regards.=0A>>>>>> =0A>>>>>> =A0 Hiroki Mo= ri=0A>>>>> =0A>>>>> =A0 Is umass.ko loaded? (I assume you are using a USB s= torage =0A> device).=0A>>>>> =0A>>>>> =A0 sean=0A>>>>> =0A>>>> =A0 ________= _______________________________________=0A>>>> =A0 freebsd-mips@freebsd.org= mailing list=0A>>>> =A0 https://lists.freebsd.org/mailman/listinfo/freebsd= -mips=0A>>>> =A0 To unsubscribe, send any mail to=0A>>> "freebsd-mips-unsu= bscribe@freebsd.org"=0A>>> =0A>> _________________________________________= ______=0A>> freebsd-mips@freebsd.org mailing list=0A>> https://lists.free= bsd.org/mailman/listinfo/freebsd-mips=0A>> To unsubscribe, send any mail t= o =0A> "freebsd-mips-unsubscribe@freebsd.org"=0A>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?262371.61155.qm>