Date: Sat, 12 Jun 2004 12:05:33 -0500 From: jml <jml@ha.cx> To: freebsd-sparc64@freebsd.org Subject: E450 installation problems Message-ID: <20040612170533.GA12295@static.protection.cx>
next in thread | raw e-mail | index | archive | help
Hi,
I'm trying to install 5.2.1 on an E450 from CDROM (generated from
5.2.1-RELEASE-sparc64-bootonly.iso).
Unfortunately, after finishing partitioning I get:
Unable to find device node for /dev/da0b in /dev!
The creation of filesystems will be aborted.
I tried jumping to a shell to run mknod but mknod doesn't seem to be
anywhere.
Did I do something wrong / is this a known issue?
Also, the raid controller doesn't appear to be in the dmesg, even as an
unconfigured device (I believe it is handled by the asr driver).
Thanks in advance for any help someone can provide. dmesg below.
Boot device: /pci@1f,4000/scsi@2/disk@6,0:f File and args:
>> FreeBSD/sparc64 boot block
Boot path: /pci@1f,4000/scsi@2/disk@6,0:f
Boot loader: /boot/loader
Console: OpenFirmware console
Boot path set to /pci@1f,4000/scsi@2/disk@6,0:a
FreeBSD/sparc64 bootstrap loader, Revision 1.0
(root@bobbi.cse.buffalo.edu, Mon Feb 23 17:51:19 GMT 2004)
bootpath="/pci@1f,4000/scsi@2/disk@6,0:a"
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x372908+0x43568 syms=[0x8+0x56040+0x8+0x44062]
|
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
nothing to autoload yet.
jumping to kernel entry at 0xc0040000.
stray vector interrupt 2029
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RELEASE #0: Tue Feb 24 07:47:33 GMT 2004
root@bobbi.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0852000.
Preloaded mfs_root "/boot/mfsroot" at 0xc0852190.
Timecounter "tick" frequency 400000000 Hz quality 0
real memory = 2147483648 (2048 MB)
avail memory = 2060804096 (1965 MB)
cpu0: Sun Microsystems UltraSparc-II Processor (400.00 MHz CPU)
cpu1: Sun Microsystems UltraSparc-II Processor (400.00 MHz CPU)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
nexus0: <OpenFirmware Nexus device>
nexus0: <associations>, type (unknown) (no driver attached)
pcib0: <U2P UPA-PCI bridge> on nexus0
pcib0: Psycho, impl 0, version 4, ign 0x7c0, bus B
pcib0: [FAST]
pcib0: [FAST]
pcib0: [FAST]
initialializing counter-timer
Timecounter "counter-timer" frequency 1000000 Hz quality 0
DVMA map: 0xfc000000 to 0xffffffff
pci0: <OFW PCI bus> on pcib0
ebus0: revision 0x01
ebus0: <PCI-EBus2 bridge> mem 0x71000000-0x717fffff,0x70000000-0x70ffffff at device 1.0 on pci0
ebus0: <auxio> addr 0x140072f000-0x140072f003,0x140072c000-0x140072c003,0x140072a000-0x140072a003,0x1400728000-0x1400728003,0x1400726000-0x1400726003 (no driver attached)
ebus0: <power> addr 0x1400724000-0x1400724003 irq 2034,2021 (no driver attached)
ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver attached)
ebus0: <sc> addr 0x1400500000-0x1400500007 (no driver attached)
sab0: <Siemens SAB 82532 v3.2> addr 0x1400400000-0x140040007f irq 43 on ebus0
sab0: [FAST]
sabtty0: <ttya> on sab0
sabtty0: console 9600,8,n,1,-
sabtty1: <ttyb> on sab0
ebus0: <su> addr 0x14003083f8-0x14003083ff irq 41 (no driver attached)
ebus0: <su> addr 0x14003062f8-0x14003062ff irq 42 (no driver attached)
ebus0: <ecpp> addr 0x1400700000-0x140070000f,0x1400300398-0x1400300399,0x14003043bc-0x14003043cb irq 2018 (no driver attached)
ebus0: <fdthree> addr 0x1400720000-0x1400720003,0x1400706000-0x140070600f,0x14003023f0-0x14003023f7 irq 2023 (no driver attached)
eeprom0: <EBus EEPROM/clock> addr 0x1400000000-0x1400001fff on ebus0
eeprom0: model mk48t59
eeprom0: hostid 80b64da3
ebus0: <flashprom> addr 0x1000000000-0x10000fffff,0x1000000000-0x10000fffff (no driver attached)
ebus0: <SUNW,envctrl> addr 0x1400600000-0x1400600003 irq 2021,2024 (no driver attached)
hme0: <Sun HME 10/100 Ethernet> mem 0x8000-0xffff at device 1.1 on pci0
hme0: Ethernet address: 08:00:20:b6:4d:a3
miibus0: <MII bus> on hme0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sym0: <875> port 0x400-0x4ff mem 0x12000-0x12fff,0x10000-0x100ff at device 3.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x800-0x8ff mem 0x16000-0x16fff,0x14000-0x140ff at device 2.0 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
pcib1: <U2P UPA-PCI bridge> on nexus0
pcib1: Psycho, impl 0, version 4, ign 0x7c0, bus A
pci1: <OFW PCI bus> on pcib1
nexus0: <mc>, type memory-controller (no driver attached)
pcib2: <U2P UPA-PCI bridge> on nexus0
pcib2: Psycho, impl 0, version 4, ign 0x100, bus B
pcib2: [FAST]
pcib2: [FAST]
pcib2: [FAST]
initialializing counter-timer
Timecounter "counter-timer" frequency 1000000 Hz quality 0
DVMA map: 0xfc000000 to 0xffffffff
pci2: <OFW PCI bus> on pcib2
pcib3: <U2P UPA-PCI bridge> on nexus0
pcib3: Psycho, impl 0, version 4, ign 0x100, bus A
pci3: <OFW PCI bus> on pcib3
pcib4: <U2P UPA-PCI bridge> on nexus0
pcib4: Psycho, impl 0, version 4, ign 0x180, bus B
pcib4: [FAST]
pcib4: [FAST]
pcib4: [FAST]
initialializing counter-timer
Timecounter "counter-timer" frequency 1000000 Hz quality 0
DVMA map: 0xfc000000 to 0xffffffff
pci4: <OFW PCI bus> on pcib4
pcib5: <OFW PCI-PCI bridge> at device 2.0 on pci4
pci5: <OFW PCI bus> on pcib5
pci5: <bridge, PCI-unknown> at device 0.0 (no driver attached)
hme1: <Sun HME 10/100 Ethernet> mem 0x4000000-0x4007fff at device 0.1 on pci5
pcib4: guessing interrupt 17 for device 2/0 pin 2
pcib5: slot 0 INTB is routed to irq 17
hme1: Ethernet address: 08:00:20:b6:4d:a3
miibus1: <MII bus> on hme1
qsphy0: <QS6612 10/100 media interface> on miibus1
qsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci5: <bridge, PCI-unknown> at device 1.0 (no driver attached)
hme2: <Sun HME 10/100 Ethernet> mem 0x8000000-0x8007fff at device 1.1 on pci5
pcib4: guessing interrupt 18 for device 2/0 pin 3
pcib5: slot 1 INTB is routed to irq 18
hme2: Ethernet address: 08:00:20:b6:4d:a3
miibus2: <MII bus> on hme2
qsphy1: <QS6612 10/100 media interface> on miibus2
qsphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci5: <bridge, PCI-unknown> at device 2.0 (no driver attached)
hme3: <Sun HME 10/100 Ethernet> mem 0xc000000-0xc007fff at device 2.1 on pci5
pcib4: guessing interrupt 19 for device 2/0 pin 4
pcib5: slot 2 INTB is routed to irq 19
hme3: Ethernet address: 08:00:20:b6:4d:a3
miibus3: <MII bus> on hme3
qsphy2: <QS6612 10/100 media interface> on miibus3
qsphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci5: <bridge, PCI-unknown> at device 3.0 (no driver attached)
hme4: <Sun HME 10/100 Ethernet> mem 0x10000000-0x10007fff at device 3.1 on pci5
pcib4: guessing interrupt 16 for device 2/0 pin 1
pcib5: slot 3 INTB is routed to irq 16
hme4: Ethernet address: 08:00:20:b6:4d:a3
miibus4: <MII bus> on hme4
qsphy3: <QS6612 10/100 media interface> on miibus4
qsphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib6: <OFW PCI-PCI bridge> at device 3.0 on pci4
pci6: <OFW PCI bus> on pcib6
pci6: <bridge, PCI-unknown> at device 0.0 (no driver attached)
hme5: <Sun HME 10/100 Ethernet> mem 0x14000000-0x14007fff at device 0.1 on pci6
pcib4: guessing interrupt 21 for device 3/0 pin 2
pcib6: slot 0 INTB is routed to irq 21
hme5: Ethernet address: 08:00:20:b6:4d:a3
miibus5: <MII bus> on hme5
qsphy4: <QS6612 10/100 media interface> on miibus5
qsphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci6: <bridge, PCI-unknown> at device 1.0 (no driver attached)
hme6: <Sun HME 10/100 Ethernet> mem 0x18000000-0x18007fff at device 1.1 on pci6
pcib4: guessing interrupt 22 for device 3/0 pin 3
pcib6: slot 1 INTB is routed to irq 22
hme6: Ethernet address: 08:00:20:b6:4d:a3
miibus6: <MII bus> on hme6
qsphy5: <QS6612 10/100 media interface> on miibus6
qsphy5: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci6: <bridge, PCI-unknown> at device 2.0 (no driver attached)
hme7: <Sun HME 10/100 Ethernet> mem 0x1c000000-0x1c007fff at device 2.1 on pci6
pcib4: guessing interrupt 23 for device 3/0 pin 4
pcib6: slot 2 INTB is routed to irq 23
hme7: Ethernet address: 08:00:20:b6:4d:a3
miibus7: <MII bus> on hme7
qsphy6: <QS6612 10/100 media interface> on miibus7
qsphy6: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci6: <bridge, PCI-unknown> at device 3.0 (no driver attached)
hme8: <Sun HME 10/100 Ethernet> mem 0x20000000-0x20007fff at device 3.1 on pci6
pcib4: guessing interrupt 20 for device 3/0 pin 1
pcib6: slot 3 INTB is routed to irq 20
hme8: Ethernet address: 08:00:20:b6:4d:a3
miibus8: <MII bus> on hme8
qsphy7: <QS6612 10/100 media interface> on miibus8
qsphy7: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib7: <OFW PCI-PCI bridge> at device 4.0 on pci4
pci7: <OFW PCI bus> on pcib7
pci7: <memory> at device 3.0 (no driver attached)
pci7: <unknown> at device 4.0 (no driver attached)
pcib8: <U2P UPA-PCI bridge> on nexus0
pcib8: Psycho, impl 0, version 4, ign 0x180, bus A
pci8: <OFW PCI bus> on pcib8
Timecounters tick every 10.000 msec
Waiting 15 seconds for SCSI devices to settle
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc044ff28
GEOM: create disk da0 dp=0xfffff80001122c68
GEOM: create disk cd0 dp=0xfffff8000083de98
da0 at sym0 bus 0 target 0 lun 0
da0: <SEAGATE ST39173W SUN9.0G 7063> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 8637MB (17689267 512 byte sectors: 255H 63S/T 1101C)
cd0 at sym1 bus 0 target 6 lun 0
cd0: <TOSHIBA XM6201TASUN32XCD 1103> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 16)
cd0: cd present [34044 x 512 byte records]
SMP: AP CPU #1 Launched!
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040612170533.GA12295>