Date: Sun, 14 May 2000 13:23:55 -0700 (PDT) From: Ken Keeler <kkeysler@nwlink.com> To: questions <freebsd-questions@FreeBSD.ORG> Subject: matcd0 not found in 4.0 Message-ID: <Pine.BSF.4.21.0005141154140.13999-100000@localhost>
next in thread | raw e-mail | index | archive | help
Hello,
I've just installed 4.0 on an older Packard Bell. It has one of
those combined modem/sound/cdrom controller cards. I had the cdrom
working under 3.1, but after a clean install of 4.0 (kernel sources
and doc only) I cannot seem to get the cdrom working.
There is no dmesg output indicating that it even sees the dang thing.
Here's the dmesg
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
FreeBSD 4.0-RELEASE #0: Sat May 13 13:54:01 PDT 2000
toor@oslo.caldonia.net:/usr/src/sys/compile/JACKSON
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 60136801 Hz
CPU: Pentium/P5 (60.14-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x517 Stepping = 7
Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory = 16777216 (16384K bytes)
avail memory = 13623296 (13304K bytes)
Preloaded elf kernel "kernel" at 0xc02d2000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc02d209c.
Intel Pentium detected, installing workaround for F00F bug
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
atapci0: <CMD 640 ATA controller !WARNING! buggy chip data loss
possible> irq 14
at device 1.0 on pci0
atapci0: Busmastering DMA not supported
isab0: <Intel 82378ZB PCI to ISA bridge> at device 2.0 on pci0
at device 1.0 on pci0
atapci0: Busmastering DMA not supported
isab0: <Intel 82378ZB PCI to ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pci0: <Cirrus Logic GD5434 SVGA controller> at 3.0 irq 11
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xfce0-0xfcff irq 10 at
device 12.0 on pci0
ed0: address 00:a0:76:a0:87:27, type NE2000 (16 bit)
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ad0: 408MB <ST3491A> [899/15/62] at ata0-master using BIOSPIO
Mounting root from ufs:/dev/ad0s1a
and the relevant device line from the kernel config file.
#Matsushita CDROM
device matcd0 at isa? port 0x340
I'm not sure what I've missed.
E=mc^2
student 1 each Ken Keeler
Phi Theta Kappa
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0005141154140.13999-100000>