Date: Thu, 02 Nov 2000 09:16:21 -0800 From: Mike Sharp <mike_sharp@pacbell.net> To: aic7xxx@FreeBSD.ORG Subject: Work on the 29160? Message-ID: <3A01A165.4F08C641@pacbell.net>
next in thread | raw e-mail | index | archive | help
Hi, Is anyone out there working on changes to support the 29160 board? It seems to work somewhat, but I'm seeing a few problems. Any thoughts would be greatly appreciated. 1. With device disconnect enabled I get the following repeated infinitely during boot: No active SCB for reconnecting target - Issuing BUS DEVICE RESET SAVED_TCL=0x1, ARG_1=0xff, SEQ_ADDR=0x11d 2. With device disconnet disabled I can get the system to boot, but I can't run at 160MB, only 40MB. The appropriate section of the boot log is below. In both cases the system in question only has a single 18Mb Seagate Cheetah attached to the 29160. Termination is not an issue. --Mike Nov 2 08:34:39 gueuze kernel: (scsi0) <Adaptec AIC-7892 Ultra 160/m SCSI host adapter> found at PCI 0/14/0 Nov 2 08:34:39 gueuze kernel: (scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs Nov 2 08:34:39 gueuze kernel: (scsi0) Downloading sequencer code... 392 instructions downloaded Nov 2 08:34:39 gueuze kernel: scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4 Nov 2 08:34:39 gueuze kernel: <Adaptec AIC-7892 Ultra 160/m SCSI host adapter> Nov 2 08:34:39 gueuze kernel: scsi : 1 host. Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 63. Nov 2 08:34:39 gueuze kernel: scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0 Test Unit Ready 00 00 00 00 00 Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out - resetting Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0 channel 0. Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 63. Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out - resetting Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0 channel 0. Nov 2 08:34:39 gueuze kernel: SCSI host 0 channel 0 reset (pid 0) timed out - trying harder Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0 channel 0. Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 160.0 Mbyte/sec, offset 63. Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out - resetting Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0 channel 0. Nov 2 08:34:39 gueuze kernel: SCSI host 0 channel 0 reset (pid 0) timed out - trying harder Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0 channel 0. Nov 2 08:34:39 gueuze kernel: (scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 63. Nov 2 08:34:39 gueuze kernel: SCSI host 0 abort (pid 0) timed out - resetting Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0 channel 0. Nov 2 08:34:39 gueuze kernel: SCSI host 0 channel 0 reset (pid 0) timed out - trying harder Nov 2 08:34:39 gueuze kernel: SCSI bus is being reset for host 0 channel 0. Nov 2 08:34:39 gueuze kernel: Vendor: SEAGATE Model: ST318404LW Rev: 3074 Nov 2 08:34:39 gueuze kernel: Type: Direct-Access ANSI SCSI revision: 03 Nov 2 08:34:39 gueuze kernel: Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 Nov 2 08:34:39 gueuze kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB] [17.5 GB] Nov 2 08:34:39 gueuze kernel: sda: sda1 sda2 < sda5 sda6 sda7 > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe aic7xxx" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3A01A165.4F08C641>