Date: Thu, 20 Jun 2002 17:30:09 -0700 (PDT) From: Nick Colakovic <nickc@CORP.FirstIndustrial.com> To: freebsd-bugs@FreeBSD.org Subject: RE: kern/39447: 4.5R &4.6R Kernels fail to boot w/ AHA2940U2W att ached to an IFT-3102 controller (in less than 10 minutes) Message-ID: <200206210030.g5L0U9N08342@freefall.freebsd.org>
next in thread | raw e-mail | index | archive | help
The following reply was made to PR kern/39447; it has been noted by GNATS.
From: Nick Colakovic <nickc@CORP.FirstIndustrial.com>
To: "'Justin T. Gibbs'" <gibbs@scsiguy.com>,
"'freebsd-gnats-submit@FreeBSD.org'" <freebsd-gnats-submit@FreeBSD.org>
Cc:
Subject: RE: kern/39447: 4.5R &4.6R Kernels fail to boot w/ AHA2940U2W att
ached to an IFT-3102 controller (in less than 10 minutes)
Date: Thu, 20 Jun 2002 19:22:30 -0500
> > 2.57.2. Enabled the USB ports in the bios, left the IDE
> primary controller
> > disabled, secondary IDE enabled (for CD-ROM) and attempted
> to boot via the
> > 4.6R boot floppies.
>
> What do you need the USB ports for? Why not disable them to remove a
> possible cause of this problem?
>
That is how these systems are configured by default. Actually I don't think
I can turn off USB on the Intel CA810E systems. The kernel configs I use of
these systems don't even include USB at the kernel level. This was
recommended to me as a solution for a boot problem related to interrupt
masking. I agree that this was a rather magical attempt at a solution.
> > Same result, the system does not get past the "Waiting
> > 15 seconds for SCSI devices to settle" phase of the kernel boot.
>
> Have you tried a verbose boot? This would at least let you see
> if the ahc driver is even attempting to talk to the device.
>
> > I would be very be inclined to point a finger at the ahc driver
> > since I have had problems w/ this driver and the IFT-3102
> before. It
> > consistently has had a minor problem with sending a cache
> sync command to
> > the 3102 at shutdown.
>
> You mean that FreeBSD occasionally complains about the sync
> cache command
> failing? This has absolutely nothing to do with the ahc
> driver. There
> is some long standing bug in the da driver that causes it to complain
> about sync cache commands failing even though there is code in there
> to be quiet about them. The quirk table is just a hack around this
> problem that should actually be fixed. If you could spend a
> bit of time
> instrumenting the sync cache code in the da driver, you might be able
> to finally fix this bug. Unfortunately, all of the hardware available
> to the SCSI engineers actually supports the sync cache
> command correctly.
I stand corrected. In the past I got the impression this was an problem
related to the ahc driver due to various patches you have provided.
> BTW, if you are using the quirk even though your controller supports
> sync cache, you are removing a very important operation that ensures
> that your data remains valid across a power cycle.
The controller has a NiMH battery designed to store cache information for a
week without power. Using sync cache is should be irrelevant with the
battery cache. In addition I disable APM in my kernel configs so the system
is not powering down at shutdown or reboot.
>
> The disturbing thing about your report is that there are no messages.
> The ahc driver sets a timeout for every command it issues. Does the
> num lock key toggle when you are in this condition?
Yes, and the kernel debugger does respond (control-alt-escape).
> Please provide a verbose boot listing. You may have to use console
> redirection in order to get one. Many MB bios have this option.
I stand corrected after 10 minutes or so the kernel did boot. Under 4.5R I
left a system for 2 hours without a successful boot. 4.6R takes about 10
minutes to boot. I wasn't patient enough to wait this long under 4.6R
assuming (foolishly) that the behavior was the same as in 4.5R. As a hack I
dropped a 4.6R kernel compiled on another system onto the root of the
existing 4.4R system (so userland is still 4.4R). Included is a verbose
listing of 4.6R kernel boot of one of the Intel 810E systems:
ok boot -v
SMAP type=01 base=00000000 00000000 len=00000000 0009fc00
SMAP type=02 base=00000000 0009fc00 len=00000000 00000400
SMAP type=02 base=00000000 000e0000 len=00000000 00020000
SMAP type=01 base=00000000 00100000 len=00000000 1fdc0000
SMAP type=03 base=00000000 1fee0000 len=00000000 00018000
SMAP type=04 base=00000000 1fef8000 len=00000000 00008000
SMAP type=03 base=00000000 1fec0000 len=00000000 00020000
SMAP type=02 base=00000000 ffb80000 len=00000000 00080000
SMAP type=02 base=00000000 fff00000 len=00000000 00100000
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-RELEASE #0: Wed Jun 19 08:37:50 CDT 2002
nickc@vanguard.firstindustrial.com:/usr/obj/usr/src/sys/SSCLEAN.R44
Calibrating clock(s) ... TSC clock: 548295083 Hz, i8254 clock: 1193099 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 548336026 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (548.34-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x681 Stepping = 1
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
PAT,PSE36,PN,MMX,FXSR,SSE
>
real memory = 535560192 (523008K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00348000 - 0x1feb7fff, 532086784 bytes (129904 pages)
avail memory = 518295552 (506148K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fda60
bios32: Entry = 0xfda74 (c00fda74) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xda95
pnpbios: Found PnP BIOS data at 0xc00f2b80
pnpbios: Entry = f0000:243a Rev = 1.0
Other BIOS signatures found:
ACPI: 000ff980
Preloaded elf kernel "kernel.r46" at 0xc0321000.
Pentium Pro MTRR support enabled
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000050
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71248086)
Using $PIR table, 10 entries at 0xc00f30f0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810E (i810E GMCH) Host To Hub bridge> on motherboard
found-> vendor=0x8086, dev=0x7124, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7125, revid=0x03
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base f8000000, size 26
map[14]: type 1, range 32, base ffa80000, size 19
found-> vendor=0x8086, dev=0x2418, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x2410, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x2411, revid=0x02
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x2412, revid=0x02
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=15
map[20]: type 1, range 32, base 0000ef80, size 5
found-> vendor=0x8086, dev=0x2413, revid=0x02
class=0c-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=14
map[20]: type 1, range 32, base 0000efa0, size 4
pci0: <PCI bus> on pcib0
pci0: <Intel 82810E (i810E GMCH) SVGA controller> (vendor=0x8086,
dev=0x7125) at 1.0 irq 11
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=15
map[10]: type 1, range 32, base ff8fe000, size 12
map[14]: type 1, range 32, base 0000df00, size 6
map[18]: type 1, range 32, base ff700000, size 20
found-> vendor=0x9005, dev=0x0010, revid=0x00
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=14
map[10]: type 1, range 32, base 0000d800, size 8
map[14]: type 1, range 64, base ff8ff000, size 12
pci1: <PCI bus> on pcib1
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xdf00-0xdf3f mem
0xff700000-0xff7fffff,0xff8fe000-0xff8fe
fff irq 15 at device 1.0 on pci1
fxp0: using memory space register mapping
fxp0: Ethernet address 00:03:47:06:d6:84
fxp0: PCI IDs: 8086 1229 8086 3000 0008
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0: <Adaptec 2940 Ultra2 SCSI adapter> port 0xd800-0xd8ff mem
0xff8ff000-0xff8fffff irq 14 at device
9.0 on pci1
ahc0: Reading SEEPROM...done.
ahc0: BIOS eeprom is present
ahc0: Secondary High byte termination Enabled
ahc0: Secondary Low byte termination Enabled
ahc0: Primary Low Byte termination Enabled
ahc0: Primary High Byte termination Enabled
ahc0: Downloading Sequencer Program... 422 instructions downloaded
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
pci0: <Unknown PCI ATA controller> (vendor=0x8086, dev=0x2411) at 31.1
pci0: <Intel 82801AA (ICH) USB controller> (vendor=0x8086, dev=0x2412) at
31.2 irq 15
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 14
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem
0xc0000-0xcbfff,0xcc000-0xccfff,0xcd000-0xd27ff,0xd2800-0xd37ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 03 28
psm: status 90 03 3c
psm: status 90 03 3c
psm: status 90 03 3c
psm: data 08 00 00
psm: data 08 00 00
psm: status 00 03 28
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 04 60 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fe3f20 0..1022=1023 cylinders, 0..63=64 heads, 1..32=32 sectors
0 accounted for
Device configuration finished.
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(ahc0:A:0:0): Sending WDTR 1
(ahc0:A:0:0): Received WDTR 1 filtered to 1
ahc0: target 0 using 16bit transfers
(ahc0:A:0:0): Sending SDTR period a, offset 7f
(ahc0:A:0:0): Received SDTR period a, offset 1f
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
(ahc0:A:0:1): Sending WDTR 1
(ahc0:A:0:1): Received WDTR 1 filtered to 1
ahc0: target 0 using asynchronous transfers
(ahc0:A:0:1): Sending SDTR period a, offset 1f
(ahc0:A:0:1): Received SDTR period a, offset 1f
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
(ahc0:A:0:1): Sending WDTR 1
(ahc0:A:0:1): Received WDTR 1 filtered to 1
ahc0: target 0 using asynchronous transfers
(ahc0:A:0:1): Sending SDTR period a, offset 7f
(ahc0:A:0:1): Received SDTR period a, offset 1f
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
(ahc0:A:0:2): Sending WDTR 1
(ahc0:A:0:2): Received WDTR 1 filtered to 1
ahc0: target 0 using asynchronous transfers
(ahc0:A:0:2): Sending SDTR period a, offset 1f
(ahc0:A:0:2): Received SDTR period a, offset 1f
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
The messages continued in a loop for 10 minutes or so then:
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
(ahc0:A:0:7): Sending WDTR 1
(ahc0:A:0:7): Received WDTR 1 filtered to 1
ahc0: target 0 using asynchronous transfers
(ahc0:A:0:7): Sending SDTR period a, offset 1f
(ahc0:A:0:7): Received SDTR period a, offset 1f
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
(probe0:ahc0:0:0:7): Vendor Specific Command. CDB: 1a e0 a 0 14 0
(probe0:ahc0:0:0:7): NOT READY asc:4,0
(probe0:ahc0:0:0:7): Logical unit not ready, cause not reportable
(ahc0:A:0:7): Sending WDTR 1
(ahc0:A:0:7): Received WDTR 1 filtered to 1
ahc0: target 0 using asynchronous transfers
(ahc0:A:0:7): Sending SDTR period a, offset 7f
(ahc0:A:0:7): Received SDTR period a, offset 1f
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
(ahc0:A:0:7): Sending WDTR 1
(ahc0:A:0:7): Received WDTR 1 filtered to 1
ahc0: target 0 using asynchronous transfers
(ahc0:A:0:7): Sending SDTR period a, offset 1f
(ahc0:A:0:7): Received SDTR period a, offset 1f
Filtered to period a, offset 1f
ahc0: target 0 synchronous at 40.0MHz, offset = 0x1f
Creating DISK da0
Creating DISK da1
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <IFT 3102 0223> Fixed Direct Access SCSI-2 device
pass0: Serial Number 3132729
pass0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass1 at ahc0 bus 0 target 0 lun 1
pass1: <IFT 3102 0223> Fixed Direct Access SCSI-2 device
pass1: Serial Number 3132729
pass1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass2 at ahc0 bus 0 target 0 lun 2
pass2: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass2: Serial Number 3132729
pass2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass3 at ahc0 bus 0 target 0 lun 3
pass3: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass3: Serial Number 3132729
pass3: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass4 at ahc0 bus 0 target 0 lun 4
pass4: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass4: Serial Number 3132729
pass4: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass5 at ahc0 bus 0 target 0 lun 5
pass5: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass5: Serial Number 3132729
pass5: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass6 at ahc0 bus 0 target 0 lun 6
pass6: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass6: Serial Number 3132729
pass6: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass7 at ahc0 bus 0 target 0 lun 7
pass7: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass7: Serial Number 3132729
pass7: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass2 at ahc0 bus 0 target 0 lun 2
pass2: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass2: Serial Number 3132729
pass2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass3 at ahc0 bus 0 target 0 lun 3
pass3: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass3: Serial Number 3132729
pass3: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass4 at ahc0 bus 0 target 0 lun 4
pass4: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass4: Serial Number 3132729
pass4: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass5 at ahc0 bus 0 target 0 lun 5
pass5: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass5: Serial Number 3132729
pass5: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass6 at ahc0 bus 0 target 0 lun 6
pass6: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass6: Serial Number 3132729
pass6: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
pass7 at ahc0 bus 0 target 0 lun 7
pass7: <IFT 3102 0223> Fixed unknown SCSI-2 device
pass7: Serial Number 3132729
pass7: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
da0 at ahc0 bus 0 target 0 lun 0
da0: <IFT 3102 0223> Fixed Direct Access SCSI-2 device
da0: Serial Number 3132729
da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
da0: 4096MB (8388608 512 byte sectors: 64H 32S/T 4096C)
da1 at ahc0 bus 0 target 0 lun 1
da1: <IFT 3102 0223> Fixed Direct Access SCSI-2 device
da1: Serial Number 3132729
da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
Enabled
da1: 4096MB (8388608 512 byte sectors: 64H 32S/T 4096C)
Mounting root from ufs:/dev/da0s1a
da0s1: type 0xa5, start 32, end = 8388607, size 8388576 : OK
start_init: trying /sbin/init
swapon: adding /dev/da0s1b as swap device
Automatic boot in progress...
/dev/da0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1a: clean, 101488 free (424 frags, 12633 blocks, 0.3d%
fragmentation)a
1s1: type 0xa5, start 32, end = 8388607, size 8388576 : OK
/dev/da0s1g: FILESYSTEM CLEAN; SKIPPING CHECKS
1dev/da0s1g: dclean, 988371 fraee (3 frags, 1231546 blocks, 0.0%s
fragmentation)
t/dev/da1s1e: FI:LESYSTEM CLEAN; SKIPPING CHECKS
/dev/da1s1e: clyean, 1692160 frepe (3264 frags, 2e11112 blocks, 0. 2%
fragmentation0)
xa5, start 32, end = 8388607, size 8388576 : OK
/dev/da0s1f: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1f: clean, 774811 free (31355 frags, 92932 blocks, 1.5%
fragmentation)
/dev/da1s1f: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da1s1f: clean, 2032379 free (19 frags, 254045 blocks, 0.0%
fragmentation)
/dev/da0s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1e: clean, 128301 free (205 frags, 16012 blocks, 0.0%
fragmentation)
da1s1: type 0xa5, start 32, end = 8388607, size 8388576 : OK
Doing initial network setup: hostname.
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 172.16.0.22 netmask 0xffffe000 broadcast 172.16.31.255
ether 00:03:47:06:d6:84
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
add net default: gateway 172.16.0.1
Additional routing options: TCP keepalive=YES.
Routing daemons:.
Additional daemons: syslogd.
Doing additional network setup: ntpd.
Starting final network daemons:.
ELF ldconfig path: /usr/lib /usr/lib/compat /usr/local/lib
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
Starting standard daemons: inetd cron sshd sendmail.
Recovering vi editor sessions:.
Initial rc.i386 initialization:.
Configuring syscons: blank_timevidcontrol: must be on a virtual console:
Inappropriate ioctl for device
.
Additional ABI support:.
Local package initialization:Starting Backup Express client
apache apcupsdbkpupsd mysqldStarting Netsaint service:
This account is currently not available.
PID TT STAT TIME COMMAND
874 ?? Rs 0:00.46 /a/services/netsaint/bin/netsaint -d
/a/services/nets
Sambapostfix/postfix-script: starting the Postfix mail system
snmpd.
Additional TCP options:.
Thu Jun 20 18:44:24 CDT 2002
FreeBSD/i386 (pariah.firstindustrial.com) (console)
login:
The system that was used for this boot has IDE, sound, and APM features
disabled. The controller is a AHA-2940U2W with 2.20 firmware. I only have
2 luns mapped to this system, I don't know exactly why the pass* devices are
being found. The WinNT 4.0 system on this same controller has the RAID
management GUI loaded. Infortrend provides a GUI for inband management of
the controller (which only runs on Windows NT4/2K and Solaris). They
require that the controller's "Peripheral Device Type" parameter to be set
to "0x1f" if the managing system is WinNT 4.0. I am guessing here but is
seems that the controller is using passthrough devices to communicate w/ the
GUI that FreeBSD doesn't like. I will try to change the Infortrend's
Peripheral Device Type parameter to the default of "0x7f" and retry. The
config file for the kernel in question is:
machine i386
#cpu I386_CPU
#cpu I486_CPU
#cpu I586_CPU
cpu I686_CPU
ident SSCLEAN
maxusers 64
makeoptions DEBUG=-g #Build kernel with gdb(1) debug
symbols
#options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
#options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Enable Directory Hashing
#options MFS #Memory Filesystem
#options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
#options NFS_ROOT #NFS usable as root device, NFS
required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
#options CD9660_ROOT #CD-ROM usable as root, CD9660
required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# Tweak Shared Memory for Squid
#options MSGMNB=16384 # max # of bytes in a queue
#options MSGMNI=41 # number of message queue identifiers
#options MSGSEG=2049 # number of message segments
#options MSGSSZ=64 # size of a message segment
#options MSGTQL=512 # max messages in system
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
#device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0
# ATA and ATAPI devices
#device ata0 at isa? port IO_WD1 irq 14
#device ata1 at isa? port IO_WD2 irq 15
#device ata
#device atadisk # ATA disk drives
#device atapicd # ATAPI CDROM drives
#device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
#options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
#options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices
when
# both sym and ncr are configured
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
#device ncv # NCR 53C500
#device nsp # Workbit Ninja SCSI-3
#device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers interfaced to the SCSI subsystem
#device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device dpt # DPT Smartcache - See LINT for options!
#device mly # Mylex AcceleRAID/eXtremeRAID
# RAID controllers
#device aac # Adaptec FSA RAID, Dell PERC2/PERC3
#device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
#device twe # 3ware Escalade
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
#pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt
console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
#device apm0 at nexus? disable flags 0x20 # Advanced Power
Management
# PCCARD (PCMCIA) support
#device card
#device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
#device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
#device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
#device txp # 3Com 3cR990 (``Typhoon'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device pcn # AMD Am79C97x PCI 10/100 NICs
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS
7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device tx # SMC EtherPower II (83c170 ``EPIC'')
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
#device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
#device ex
#device ep
#device fe0 at isa? port 0x300
# Xircom Ethernet
#device xe
# PRISM I IEEE 802.11b wireless NIC.
#device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
#device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
#pseudo-device ppp 1 # Kernel PPP
#pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
#pseudo-device md # Memory "disks"
#pseudo-device gif # IPv6 and IPv4 tunneling
#pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
#pseudo-device bpf #Berkeley packet filter
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
#device usb # USB Bus (required)
#device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
#device uscanner # Scanners
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
options DDB
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-bugs" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200206210030.g5L0U9N08342>