Date: Wed, 23 May 2001 11:44:57 -0500 From: "Jacques A. Vidrine" <n@nectar.com> To: freebsd-mobile@freebsd.org Subject: SlimSCSI grief Message-ID: <20010523114457.A606@shade.nectar.com>
next in thread | raw e-mail | index | archive | help
[this is regarding FreeBSD 4.3-RELEASE, by the way]
Hello,
I'm having the darndest time getting an Adaptec SlimSCSI 1460B PC Card
to work. I thought I understood all this gunk by now, but I'm
stumped.
I used this card previously in a Sony VAIO Z505SX. Perhaps I was
lucky -- I just plugged it in, and away she went. Now I'm having
trouble with a ThinkPad X20. Especially frustrating since I've had
easy success with Linksys 802.11, Aironet 802.11, and the built-in
CompactFlash slot.
I've tried several different configurations with no success, but here
is what seems simplest to me, followed by good stuff like pccard debug
output, dumpcis, relevant kernel config stuff, and so on. I hope
someone can point me in a further direction to snoop.
Kernel config:
device card
device pcic0 at isa? irq 3 port 0x3e0 iomem 0xd0000
device aic0 at isa? port 0x340 irq 10
IRQ 10 and port 0x340 are not used by any other device.
Stock /etc/defaults/pccard.conf:
# Adaptec SlimSCSI (also included with Sony CD-ROM players)
card "Adaptec, Inc." "/APA-1460 .*/"
config 0x9 "aic" ?
insert camcontrol rescan $device
My /etc/pccard.conf:
debuglevel 9
irq 10 9
card "64MB" " "
config 0x1 "ata" ?
Chipset info:
pcic-pci0: <Ricoh RL5C476 PCI-CardBus Bridge> mem 0x50000000-0x50000fff irq 11 at device 8.0 on pci0
pcic-pci0: Legacy address set to 0x3e0
pcic-pci1: <Ricoh RL5C476 PCI-CardBus Bridge> mem 0x50100000-0x50100fff irq 9 at device 8.1 on pci0
pcic0: <Intel i82365> at port 0x3e0 iomem 0xd0000 irq 3 on isa0
pcic0: management irq 3
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
pccardc dumpcis:
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: 00 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 3
000: 12 00 ff
Attribute memory device information:
Device number 1, type Mask ROM, WPS = OFF
Speed = 200nS, Memory block size = 512b, 1 units
Tuple #3, code = 0x15 (Version 1 info), length = 57
000: 04 01 41 64 61 70 74 65 63 2c 20 49 6e 63 2e 00
010: 41 50 41 2d 31 34 36 30 20 53 43 53 49 20 48 6f
020: 73 74 20 41 64 61 70 74 65 72 00 56 65 72 73 69
030: 6f 6e 20 30 2e 30 31 00 ff
Version = 4.1, Manuf = [Adaptec, Inc.], card vers = [APA-1460 SCSI Host Adapter]
Addit. info = [Version 0.01]
Tuple #4, code = 0x20 (Manufacturer ID), length = 4
000: 2f 01 02 00
PCMCIA ID = 0x12f, OEM ID = 0x2
Tuple #5, code = 0x1a (Configuration map), length = 5
000: 01 08 00 20 01
Reg len = 2, config register addr = 0x2000, last config = 0x8
Registers: X-------
Tuple #6, code = 0x1b (Configuration entry), length = 15
000: c9 01 19 49 55 65 06 ca 60 40 03 1f 30 00 1e
Config index = 0x9(default)
Interface byte = 0x1 (I/O)
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 6 x 10mA
Power down supply current: 1 x 100mA
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
IRQ modes: Level
IRQs: 9 10 11 12
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 08 08 ca 60 40 01 1f
Config index = 0x8
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x140 block length = 0x20
Tuple #8, code = 0x14 (No link), length = 0
Tuple #9, code = 0xff (Terminator), length = 0
2 slots found
pccardd debug output interspersed with kernel verbose messages upon
insert of SlimSCSI card:
Slot 0 chg = 0x8
Slot 0 chg = 0x8
pccard: card inserted, slot 0
May 23 11:13:53 shade pccardd[123]: Card "Adaptec, Inc."("APA-1460 SCSI Host Adapter") [Version 0.01] [(null)] matched "Adaptec, Inc." ("/APA-1460 .*/") [(null)] [(null)]
May 23 11:13:53 shade pccardd[123]: Using I/O addr 0x340, size 32
May 23 11:13:53 shade pccardd[123]: Setting config reg at offs 0x2000 to 0x49, Reset time = 50 ms
May 23 11:13:58 shade pccardd[123]: Assigning I/O window 0, start 0x340, size 0x20 flags 0x5
May 23 11:13:58 shade pccardd[123]: Assign aic0, io 0x340-0x35f, mem 0x0, 0 bytes, irq 10, flags 0
aic-: aic0 exists, using next available unit number
pcic: I/O win 0 flags 15 340-35f
pcic: I/O win 0 flags 5 340-35f
May 23 11:13:58 shade pccardd[123]: driver allocation failed for Adaptec, Inc.(/APA-1460 .*/): Device not configured
Any ideas are much appreciated!
Cheers,
--
Jacques Vidrine / n@nectar.com / jvidrine@verio.net / nectar@FreeBSD.org
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20010523114457.A606>