Date: Sun, 20 Sep 2009 09:45:35 -0700 From: Joseph Olatt <joji@eskimo.com> To: "N. Raghavendra" <raghu@mri.ernet.in> Cc: FreeBSD Question <questions@freebsd.org> Subject: Re: Unable to use CD/DVD drive Message-ID: <20090920164535.GA24904@shell.eskimo.com> In-Reply-To: <86zl8q1c67.fsf@riemann.mri.ernet.in> References: <86zl8q1c67.fsf@riemann.mri.ernet.in>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sun, Sep 20, 2009 at 09:48:40AM +0530, N. Raghavendra wrote: > Until a couple of months ago, I was able to read and write CDs and > DVDs. Since then, I haven't been able to do so. When I try to mount > a CD/DVD, the process just hangs without the media being mounted, or I > get errors like this: > > [root@griffin:/root]# mount /cdrom > mount_cd9660: /dev/acd0: Input/output error > > Also, `/var/log/messages' shows lines like > > Sep 20 09:11:51 griffin kernel: g_vfs_done():acd0[READ(offset=32768, length=2048)]error = 5 > > Similar messages occur when I try to write a CD/DVD using cdrecord(1). > The CD/DVD drive is a `<PBDS DVD+-RW DH-16W1S 2D14> Removable CD-ROM > SCSI-0 device'. I upgraded my kernel to no avail. > > More details are below. Any help is appreciated. > > Thanks and regards, > Raghavendra. > > ---------------------------------------------------------------------- > > 1. Output of dmesg: attached. > > 2. Kernel configuration file > ---------------------------- > > include "GENERIC" > ident GRIFFIN > device atapicam > device sound > device snd_hda > options ACCEPT_FILTER_HTTP > > 3. /boot/loader.conf > -------------------- > > nvidia_load="YES" > hw.ata.ata_dma="1" > > 4. /etc/fstab > ------------- > > # Device Mountpoint FStype Options Dump Pass# > /dev/ad4s3b none swap sw 0 0 > /dev/ad4s3a / ufs rw 1 1 > /dev/ad4s3f /home ufs rw 2 2 > /dev/ad4s3e /opt ufs rw 2 2 > /dev/ad4s3h /tmp ufs rw 2 2 > /dev/ad4s3d /usr ufs rw 2 2 > /dev/ad4s3g /var ufs rw 2 2 > /dev/acd0 /cdrom cd9660 ro,noauto 0 0 > > 5. Output of `cdrecord --scanbus' > -------------------------------- > > [root@griffin:/root]# cdrecord -scanbus > Cdrecord-Clone 2.01 (i386-unknown-freebsd7.0) Copyright (C) 1995-2004 Jorg Schilling > Using libscg version 'schily-0.8'. > scsibus0: > 0,0,0 0) 'TEAC ' 'USB HS-CF Card' '4.08' Removable > Disk > 0,1,0 1) * > 0,2,0 2) * > 0,3,0 3) * > 0,4,0 4) * > 0,5,0 5) * > 0,6,0 6) * > 0,7,0 7) * > scsibus4: > 4,0,0 400) 'PBDS ' 'DVD+-RW DH-16W1S' '2D14' Removable > CD-ROM > 4,1,0 401) * > 4,2,0 402) * > 4,3,0 403) * > 4,4,0 404) * > 4,5,0 405) * > 4,6,0 406) * > 4,7,0 407) * > > -- > N. Raghavendra <raghu@mri.ernet.in> | http://www.retrotexts.net/ > Harish-Chandra Research Institute | http://www.mri.ernet.in/ > See message headers for contact and OpenPGP information. > > > Copyright (c) 1992-2009 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 7.2-STABLE #3: Thu Sep 10 21:00:51 IST 2009 > root@griffin.campus.hri:/usr/obj/usr/src/sys/GRIFFIN > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (2394.01-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x6fb Stepping = 11 > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM> > AMD Features=0x20100000<NX,LM> > AMD Features2=0x1<LAHF> > Cores per package: 4 > real memory = 3219718144 (3070 MB) > avail memory = 3136708608 (2991 MB) > ACPI APIC Table: <DELL FX09 > > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > cpu0 (BSP): APIC ID: 0 > cpu1 (AP): APIC ID: 1 > cpu2 (AP): APIC ID: 2 > cpu3 (AP): APIC ID: 3 > ioapic0: Changing APIC ID to 4 > ioapic0 <Version 2.0> irqs 0-23 on motherboard > kbd1 at kbdmux0 > acpi0: <DELL FX09 > on motherboard > acpi0: [ITHREAD] > acpi0: Power Button (fixed) > acpi0: reservation of 0, a0000 (3) failed > acpi0: reservation of 100000, bfd90000 (3) failed > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > device_attach: acpi_hpet0 attach returned 12 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <PCI-PCI bridge> irq 16 at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > vgapci0: <VGA-compatible display> port 0xcf00-0xcf7f mem 0xfa000000-0xfaffffff,0xd0000000-0xdfffffff,0xf8000000-0xf9ffffff irq 16 at device 0.0 on pci1 > nvidia0: <GeForce 8600 GT> on vgapci0 > vgapci0: child nvidia0 requested pci_enable_busmaster > vgapci0: child nvidia0 requested pci_enable_io > nvidia0: [GIANT-LOCKED] > nvidia0: [ITHREAD] > em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0xff00-0xff1f mem 0xfdfc0000-0xfdfdffff,0xfdfff000-0xfdffffff irq 20 at device 25.0 on pci0 > em0: Using MSI interrupt > em0: [FILTER] > em0: Ethernet address: 00:1d:09:99:b5:ee > uhci0: <UHCI (generic) USB controller> port 0xfe00-0xfe1f irq 16 at device 26.0 on pci0 > uhci0: [GIANT-LOCKED] > uhci0: [ITHREAD] > usb0: <UHCI (generic) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 > uhub0: 2 ports with 2 removable, self powered > uhci1: <UHCI (generic) USB controller> port 0xfd00-0xfd1f irq 21 at device 26.1 on pci0 > uhci1: [GIANT-LOCKED] > uhci1: [ITHREAD] > usb1: <UHCI (generic) USB controller> on uhci1 > usb1: USB revision 1.0 > uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 > uhub1: 2 ports with 2 removable, self powered > uhci2: <UHCI (generic) USB controller> port 0xfc00-0xfc1f irq 19 at device 26.2 on pci0 > uhci2: [GIANT-LOCKED] > uhci2: [ITHREAD] > usb2: <UHCI (generic) USB controller> on uhci2 > usb2: USB revision 1.0 > uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 > uhub2: 2 ports with 2 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfdffe000-0xfdffe3ff irq 18 at device 26.7 on pci0 > ehci0: [GIANT-LOCKED] > ehci0: [ITHREAD] > usb3: EHCI version 1.0 > usb3: companion controllers, 2 ports each: usb0 usb1 usb2 > usb3: <EHCI (generic) USB 2.0 controller> on ehci0 > usb3: USB revision 2.0 > uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3 > uhub3: 6 ports with 6 removable, self powered > hdac0: <Intel 82801I High Definition Audio Controller> mem 0xfdff4000-0xfdff7fff irq 22 at device 27.0 on pci0 > hdac0: HDA Driver Revision: 20090624_0136 > hdac0: [ITHREAD] > uhci3: <UHCI (generic) USB controller> port 0xfb00-0xfb1f irq 23 at device 29.0 on pci0 > uhci3: [GIANT-LOCKED] > uhci3: [ITHREAD] > usb4: <UHCI (generic) USB controller> on uhci3 > usb4: USB revision 1.0 > uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4 > uhub4: 2 ports with 2 removable, self powered > uhci4: <UHCI (generic) USB controller> port 0xfa00-0xfa1f irq 19 at device 29.1 on pci0 > uhci4: [GIANT-LOCKED] > uhci4: [ITHREAD] > usb5: <UHCI (generic) USB controller> on uhci4 > usb5: USB revision 1.0 > uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5 > uhub5: 2 ports with 2 removable, self powered > uhci5: <UHCI (generic) USB controller> port 0xf900-0xf91f irq 18 at device 29.2 on pci0 > uhci5: [GIANT-LOCKED] > uhci5: [ITHREAD] > usb6: <UHCI (generic) USB controller> on uhci5 > usb6: USB revision 1.0 > uhub6: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6 > uhub6: 2 ports with 2 removable, self powered > ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfdffd000-0xfdffd3ff irq 23 at device 29.7 on pci0 > ehci1: [GIANT-LOCKED] > ehci1: [ITHREAD] > usb7: EHCI version 1.0 > usb7: companion controllers, 2 ports each: usb4 usb5 usb6 > usb7: <EHCI (generic) USB 2.0 controller> on ehci1 > usb7: USB revision 2.0 > uhub7: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb7 > uhub7: 6 ports with 6 removable, self powered > umass0: <TEAC CA-200, class 0/0, rev 2.00/4.08, addr 2> on uhub7 > pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH9 SATA300 controller> port 0xf800-0xf807,0xf700-0xf703,0xf600-0xf607,0xf500-0xf503,0xf400-0xf40f,0xf300-0xf30f irq 19 at device 31.2 on pci0 > atapci0: [ITHREAD] > ata2: <ATA channel 0> on atapci0 > ata2: [ITHREAD] > ata3: <ATA channel 1> on atapci0 > ata3: [ITHREAD] > pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > atapci1: <Intel ICH9 SATA300 controller> port 0xf100-0xf107,0xf000-0xf003,0xef00-0xef07,0xee00-0xee03,0xed00-0xed0f,0xec00-0xec0f irq 19 at device 31.5 on pci0 > atapci1: [ITHREAD] > ata4: <ATA channel 0> on atapci1 > ata4: [ITHREAD] > ata5: <ATA channel 1> on atapci1 > ata5: [ITHREAD] > acpi_tz0: <Thermal Zone> on acpi0 > fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 > fdc0: [FILTER] > cpu0: <ACPI CPU> on acpi0 > est0: <Enhanced SpeedStep Frequency Control> on cpu0 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 927092706000927 > device_attach: est0 attach returned 6 > p4tcc0: <CPU Frequency Thermal Control> on cpu0 > cpu1: <ACPI CPU> on acpi0 > est1: <Enhanced SpeedStep Frequency Control> on cpu1 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 927092706000927 > device_attach: est1 attach returned 6 > p4tcc1: <CPU Frequency Thermal Control> on cpu1 > cpu2: <ACPI CPU> on acpi0 > est2: <Enhanced SpeedStep Frequency Control> on cpu2 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 927092706000927 > device_attach: est2 attach returned 6 > p4tcc2: <CPU Frequency Thermal Control> on cpu2 > cpu3: <ACPI CPU> on acpi0 > est3: <Enhanced SpeedStep Frequency Control> on cpu3 > est: CPU supports Enhanced Speedstep, but is not recognized. > est: cpu_vendor GenuineIntel, msr 927092706000927 > device_attach: est3 attach returned 6 > p4tcc3: <CPU Frequency Thermal Control> on cpu3 > acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 > device_attach: acpi_hpet0 attach returned 12 > pmtimer0 on isa0 > ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 > ata0: [ITHREAD] > ata1 at port 0x170-0x177,0x376 irq 15 on isa0 > ata1: [ITHREAD] > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > atkbd0: [ITHREAD] > ppc0: parallel port not found. > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 8250 or not responding > sio0: [FILTER] > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > uhub8: <Dell Dell USB Keyboard Hub, class 9/0, rev 1.10/48.01, addr 2> on uhub2 > uhub8: 3 ports with 2 removable, bus powered > ukbd0: <Dell Dell USB Keyboard Hub, class 0/0, rev 1.10/48.00, addr 3> on uhub8 > kbd2 at ukbd0 > uhid0: <Dell Dell USB Keyboard Hub, class 0/0, rev 1.10/48.00, addr 3> on uhub8 > Timecounters tick every 1.000 msec > ad4: 305245MB <Seagate ST3320620AS 3.ADG> at ata2-master SATA300 > (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 > (probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:0): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:0): NOT READY asc:3a,0 > (probe0:umass-sim0:0:0:0): Medium not present > (probe0:umass-sim0:0:0:0): Unretryable error > (probe0:umass-sim0:0:0:1): TEST UNIT READY. CDB: 0 20 0 0 0 0 > (probe0:umass-sim0:0:0:1): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:1): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:1): NOT READY asc:3a,0 > (probe0:umass-sim0:0:0:1): Medium not present > (probe0:umass-sim0:0:0:1): Unretryable error > (probe0:umass-sim0:0:0:2): TEST UNIT READY. CDB: 0 40 0 0 0 0 > (probe0:umass-sim0:0:0:2): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:2): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:2): NOT READY asc:3a,0 > (probe0:umass-sim0:0:0:2): Medium not present > (probe0:umass-sim0:0:0:2): Unretryable error > (probe0:umass-sim0:0:0:3): TEST UNIT READY. CDB: 0 60 0 0 0 0 > (probe0:umass-sim0:0:0:3): CAM Status: SCSI Status Error > (probe0:umass-sim0:0:0:3): SCSI Status: Check Condition > (probe0:umass-sim0:0:0:3): NOT READY asc:3a,0 > (probe0:umass-sim0:0:0:3): Medium not present > (probe0:umass-sim0:0:0:3): Unretryable error > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <TEAC USB HS-CF Card 4.08> Removable Direct Access SCSI-0 device > da0: 40.000MB/s transfers > da0: Attempt to query device size failed: NOT READY, Medium not present > da1 at umass-sim0 bus 0 target 0 lun 1 > da1: <TEAC USB HS-xD/SM 4.08> Removable Direct Access SCSI-0 device > da1: 40.000MB/s transfers > da1: Attempt to query device size failed: NOT READY, Medium not present > da2 at umass-sim0 bus 0 target 0 lun 2 > da2: <TEAC USB HS-MS Card 4.08> Removable Direct Access SCSI-0 device > da2: 40.000MB/s transfers > da2: Attempt to query device size failed: NOT READY, Medium not present > da3 at umass-sim0 bus 0 target 0 lun 3 > da3: <TEAC USB HS-SD Card 4.08> Removable Direct Access SCSI-0 device > da3: 40.000MB/s transfers > da3: Attempt to query device size failed: NOT READY, Medium not present > acd0: DVDR <PBDS DVD+/-RW DH-16W1S/2D14> at ata3-master SATA150 > hdac0: HDA Codec #2: Realtek ALC888 > pcm0: <HDA Realtek ALC888 PCM #0 Analog> at cad 2 nid 1 on hdac0 > pcm1: <HDA Realtek ALC888 PCM #1 Analog> at cad 2 nid 1 on hdac0 > SMP: AP CPU #1 Launched! > SMP: AP CPU #2 Launched! > SMP: AP CPU #3 Launched! > acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 > Trying to mount root from ufs:/dev/ad4s3a > WARNING: / was not properly dismounted > (probe0:ata3:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 > (probe0:ata3:0:0:0): CAM Status: SCSI Status Error > (probe0:ata3:0:0:0): SCSI Status: Check Condition > (probe0:ata3:0:0:0): NOT READY asc:3a,0 > (probe0:ata3:0:0:0): Medium not present > (probe0:ata3:0:0:0): Unretryable error > cd0 at ata3 bus 0 target 0 lun 0 > cd0: <PBDS DVD+-RW DH-16W1S 2D14> Removable CD-ROM SCSI-0 device > cd0: 3.300MB/s transfers > cd0: Attempt to query device size failed: NOT READY, Medium not present > WARNING: /home was not properly dismounted > WARNING: /opt was not properly dismounted > WARNING: /tmp was not properly dismounted > WARNING: /usr was not properly dismounted > WARNING: /var was not properly dismounted > ums0: <vendor 0x0461 USB Optical Mouse, class 0/0, rev 2.00/2.00, addr 4> on uhub2 > ums0: 3 buttons and Z dir. > em0: link state changed to DOWN > em0: link state changed to UP > em0: link state changed to DOWN > em0: link state changed to UP > em0: link state changed to DOWN > em0: link state changed to UP > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > em0: link state changed to DOWN > em0: link state changed to UP > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > arp: unknown hardware address format (0x0000) > em0: link state changed to DOWN > em0: link state changed to UP > g_vfs_done():acd0[READ(offset=32768, length=2048)]error = 5 > _______________________________________________ > freebsd-questions@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org" Just to rule out hardware problems with your CD/DVD drive, you might want to put in a live CD of Ubuntu (or PCBSD) and see if your CD/DVD drive works fine.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20090920164535.GA24904>