From owner-freebsd-scsi@FreeBSD.ORG Tue Jun 1 16:04:52 2004 Return-Path: Delivered-To: freebsd-scsi@freebsd.org Received: from mx1.FreeBSD.org (mx1.freebsd.org [216.136.204.125]) by hub.freebsd.org (Postfix) with ESMTP id A506C16A4CE for ; Tue, 1 Jun 2004 16:04:52 -0700 (PDT) Received: from vjofn.tucs-beachin-obx-house.com (vjofn.tucs-beachin-obx-house.com [204.107.90.128]) by mx1.FreeBSD.org (Postfix) with ESMTP id 5934043D45 for ; Tue, 1 Jun 2004 16:04:52 -0700 (PDT) (envelope-from tuc@tucs-beachin-obx-house.com) Received: from himinbjorg.tucs-beachin-obx-house.com (ool-44c09852.dyn.optonline.net [68.192.152.82]) (authenticated bits=128)i51N4pYT018214 for ; Tue, 1 Jun 2004 19:04:51 -0400 (EDT) Received: from himinbjorg.tucs-beachin-obx-house.com (localhost.tucs-beachin-obx-house.com [127.0.0.1])id i51N4pod013289 for ; Tue, 1 Jun 2004 19:04:51 -0400 (EDT) (envelope-from tuc@tucs-beachin-obx-house.com) Received: (from tucobx@localhost)i51N4pV4013286 for freebsd-scsi@freebsd.org; Tue, 1 Jun 2004 19:04:51 -0400 (EDT) (envelope-from tucobx) From: Tuc at Beach House Message-Id: <200406012304.i51N4pV4013286@himinbjorg.tucs-beachin-obx-house.com> To: freebsd-scsi@freebsd.org Date: Tue, 1 Jun 2004 19:04:51 -0400 (EDT) X-Mailer: ELM [version 2.5 PL6] MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Subject: 1TB issue X-BeenThere: freebsd-scsi@freebsd.org X-Mailman-Version: 2.1.1 Precedence: list List-Id: SCSI subsystem List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , X-List-Received-Date: Tue, 01 Jun 2004 23:04:52 -0000 Hi, Having a SCSI Geometry issue on a 5.2.1-RELEASE-p4 system. It has a Symbios SDMS PCI SCSI, 53C1010-66 adapter that shows up as : sym0: <1010-66> port 0xa000-0xa0ff mem 0xf6000000-0xf6001fff,0xf6800000-0xf68003 ff irq 25 at device 5.0 on pci1 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. And to it I'm connecting an EasyRaid II RAID box. There is LITTLE I can configure on it, basically termination, SCSI ID, and Raid 0/1/0+1/3/5 and thats pretty much it. When the system boots, the splash screen claims the geometry is 1024/255/63 at 40M sync, and 16 wide. In the controller I've used "Alternate CHS Mapping" and "SCSI Plug and Play Mapping" without any differences. When FreeBSD boots, it sees : (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. da0 at sym1 bus 0 target 3 lun 0 da0: Fixed Direct Access SCSI-2 device da0: 40.000MB/s transfers (20.000MHz, offset 31, 16bit), Tagged Queueing Enabled da0: 1060184MB (2171256832 512 byte sectors: 255H 63S/T 135154C) When I try to /stand/sysinstall it, fdisk pitches a serious fit about it. What can I do to get this configured properly? It seems that if I bring it down to RAID-1+0, it configures up fine (Not sure what the geometry shows as, sorry). Thanks, Tuc