From owner-freebsd-mobile Fri Aug 27 14:59: 2 1999 Delivered-To: freebsd-mobile@freebsd.org Received: from jasper.heartland.ab.ca (jasper.heartland.ab.ca [207.107.228.1]) by hub.freebsd.org (Postfix) with ESMTP id 264081557D for ; Fri, 27 Aug 1999 14:58:56 -0700 (PDT) (envelope-from dkwiebe@heartland.ab.ca) Received: from heartland.ab.ca (ppp5.heartland.ab.ca [207.107.228.133]) by jasper.heartland.ab.ca (8.9.0/8.9.0) with ESMTP id PAA21891 for ; Fri, 27 Aug 1999 15:50:59 -0600 (MDT) Message-ID: <37C70B10.2B3DE859@heartland.ab.ca> Date: Fri, 27 Aug 1999 16:02:56 -0600 From: Darren WIebe Reply-To: dkwiebe@hagenhomes.com X-Mailer: Mozilla 4.61 [en] (X11; U; FreeBSD 3.2-STABLE i386) X-Accept-Language: en MIME-Version: 1.0 To: freebsd-mobile@freebsd.org Subject: GVC 33.6 PCMCIA modem (not initialized properly) Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Sender: owner-freebsd-mobile@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.org Hello: I just recently bought the above mentioned modem. I see that in the pccard.conf file it mentions that modem except it calls it a C34+ rather than the V34+ that it calls itself. Anyhow when I insert it it gives the following erro message: "Aug 27 15:40:06 thinkpad pccardd[51]: Card "CIRRUS LOGIC V34+ 33.6Kbps MODEM"("CL-MD34XX") [3.07] [(null)] has function ID 2" **It repeats this 3 times, then it repeats the following lines 3 times*** "Aug 27 15:40:06 thinkpad pccardd[51]: Resource allocation failure for "CIRRUS LOGIC V34+ 33.6Kbps MODEM"("CL-MD34XX") [3.07] [(null)]; Reason specified CIS was not found" This modem works under dos and linux, as a point of interest. I searched through the mailing list archives and found a similar problem that somebody else had quite a while ago. I tried the solution but could not get it to work... I would really appreciate it if somebody could let me know what I am doing wrong. And I would appreciate it if you could CC the message to me, seeing that I am not sure that majordomo has signed me up to the list yet. TIA Darren Wiebe dkwiebe@hagenhomes.com Here is my cisdump Code 224 not found Code 224 not found code Unknown ignored Configuration data for card in slot 0 Tuple #1, code = 0x1 (Common memory descriptor), length = 2 000: 00 ff Common memory device information: Device number 1, type No device, WPS = OFF Speed = No speed, Memory block size = reserved, 32 units Tuple #2, code = 0x15 (Version 1 info), length = 51 000: 05 01 43 49 52 52 55 53 20 4c 4f 47 49 43 20 56 010: 33 34 2b 20 33 33 2e 36 4b 62 70 73 20 4d 4f 44 020: 45 4d 00 43 4c 2d 4d 44 33 34 58 58 00 33 2e 30 030: 37 00 ff Version = 5.1, Manuf = [CIRRUS LOGIC V34+ 33.6Kbps MODEM], card vers = [CL-MD34XX] Addit. info = [3.07] Tuple #3, code = 0x20 (Manufacturer ID), length = 4 000: 4e 01 88 00 PCMCIA ID = 0x14e, OEM ID = 0x88 Tuple #4, code = 0x21 (Functional ID), length = 2 000: 02 01 Serial port/modem - POST initialize Tuple #5, code = 0x1a (Configuration map), length = 5 000: 01 24 00 01 13 Reg len = 2, config register addr = 0x100, last config = 0x24 Registers: XX--X--- Tuple #6, code = 0x1b (Configuration entry), length = 19 000: e0 81 9d 5f 55 4d 5d 0e 1e 05 fc 14 aa 60 f8 03 010: 07 24 28 Config index = 0x20(default) Interface byte = 0x81 (I/O) wait signal supported Vcc pwr: Nominal operating supply voltage: 5 x 1V Minimum operating supply voltage: 4.5 x 1V Maximum operating supply voltage: 5.5 x 1V Continuous supply current: 1.2 x 100mA Max current average over 1 second: 1.5 x 100mA Power down supply current: 1 x 10mA Wait scale Speed = 1.2 x 10 us Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x3f8 block length = 0x8 IRQ modes: Level IRQ level = 4 Max twin cards = 0 Misc attr: (Audio-BVD2) (Power down supported) Tuple #7, code = 0x1b (Configuration entry), length = 7 000: 21 08 aa 60 f8 02 07 Config index = 0x21 Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x2f8 block length = 0x8 Tuple #8, code = 0x1b (Configuration entry), length = 7 000: 22 08 aa 60 e8 03 07 Config index = 0x22 Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x3e8 block length = 0x8 Tuple #9, code = 0x1b (Configuration entry), length = 7 000: 23 08 aa 60 e8 02 07 Config index = 0x23 Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x2e8 block length = 0x8 Tuple #10, code = 0x1b (Configuration entry), length = 6 000: 24 18 23 30 00 00 Config index = 0x24 Card decodes 3 address lines, 8 Bit I/O only IRQ modes: Level IRQs: Tuple #11, code = 0x14 (No link), length = 0 Tuple #12, code = 0x0 (Null tuple), length = 3 000: 20 ff 24 Tuple #13, code = 0xff (Terminator), length = 0 2 slots found To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message