Date: Tue, 06 Feb 2007 21:28:45 -0500 From: Mike Tancsa <mike@sentex.net> To: "N. Harrington" <drumslayer2@yahoo.com> Cc: freebsd-questions@freebsd.org Subject: Re: Problem with Serverworks HT1000 serial ATA support - Tyan S3992 Motherboard Message-ID: <jgdis250dn0lm13f0g61khevmq9fjqtkr3@4ax.com> In-Reply-To: <932351.10276.qm@web34510.mail.mud.yahoo.com> References: <932351.10276.qm@web34510.mail.mud.yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, 6 Feb 2007 15:26:27 -0800 (PST), in
sentex.lists.freebsd.questions you wrote:
>
> If I run: bonnie++ -d /home -u root s1g
> The system reboots.
>
> I have tried this is both S-ATA and P-ATA emulation.
>atapci0: <ServerWorks HT1000 SATA150 controller> port
>0xb080-0xb087,0xb000-0xb003,0xac00-0xac07
>,0xa880-0xa883,0xa800-0xa81f mem 0xff4fe000-0xff4fffff
>irq 11 at device 14.0 on pci1
>
>S-ATA:
>ad4: 70911MB <WDC WD740ADFD-00NLR1 20.07P20> at
>ata2-master SATA150
>
> OR
>P-ATA:
>ad4: DMA limited to UDMA33, device found non-ATA66
>cable
>ad4: 70911MB <WDC WD740ADFD-00NLR1 20.07P20> at
>ata2-master UDMA33
I use RELENG_6 in i386 mode on this MB (two integrated em nics) and it
works quite well
atapci0: <ServerWorks HT1000 SATA150 controller> port
0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb81f
mem 0xff
3fe000-0xff3fffff irq 11 at device 14.0 on pci1
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
ata4: <ATA channel 2> on atapci0
ata5: <ATA channel 3> on atapci0
atapci1: <ServerWorks HT1000 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 2.1 on
pci0
ata0: <ATA channel 0> on atapci1
ata1: <ATA channel 1> on atapci1
ad4: 76319MB <Seagate ST380811AS 3.AAE> at ata2-master SATA150
# atacontrol list
ATA channel 0:
Master: no device present
Slave: no device present
ATA channel 1:
Master: no device present
Slave: no device present
ATA channel 2:
Master: ad4 <ST380811AS/3.AAE> Serial ATA II
Slave: no device present
ATA channel 3:
Master: no device present
Slave: no device present
ATA channel 4:
Master: no device present
Slave: no device present
ATA channel 5:
Master: no device present
Slave: no device present
However, update the BIOS and make sure you dont use PATA emulation on
the SATA controller as that doesnt really work.=20
---Mike
--------------------------------------------------------
Mike Tancsa, Sentex communications http://www.sentex.net
Providing Internet Access since 1994
mike@sentex.net, (http://www.tancsa.com)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?jgdis250dn0lm13f0g61khevmq9fjqtkr3>