Date: Fri, 30 Apr 1999 12:02:17 -0700 (PDT) From: Doug White <dwhite@resnet.uoregon.edu> To: flygt@sr.se Cc: FreeBSD Questions <freebsd-questions@FreeBSD.ORG> Subject: Re: Adding SCSI-disks results in failure - adding dmesg Message-ID: <Pine.BSF.4.03.9904301159520.16807-100000@resnet.uoregon.edu> In-Reply-To: <19990429120138.A80213@sr.se>
next in thread | previous in thread | raw e-mail | index | archive | help
On Thu, 29 Apr 1999, Gunnar Flygt wrote: > I didn't have the dmesg output when I wrote the first message I'll > append it on the end here including the error message. Please describe the SCSI chain before and after you connect the CDROM. > First here is the errro message: > bash-2.02# newfs /dev/da7s1a > newfs: /dev/da7s1a: Device not configured Try running '/dev/MAKEDEV da7'. I'll leave the dmesg on, minus the INN problems. > And then dmesg output: > Copyright (c) 1992-1999 FreeBSD Inc. > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights > reserved. > FreeBSD 3.1-RELEASE #0: Wed Apr 28 14:54:35 CEST 1999 > root@news.sr.se:/usr/src/sys/compile/HOCKEY > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium II/Xeon/Celeron (349.13-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x652 Stepping=2 > +Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT > +,PSE36,MMX,<b24>> > real memory = 268435456 (262144K bytes) > avail memory = 257941504 (251896K bytes) > Preloaded elf kernel "kernel" at 0xf0336000. > Probing for devices on PCI bus 0: > chip0: <Intel 82443BX host to PCI bridge> rev 0x03 on pci0.0.0 > chip1: <Intel 82443BX host to AGP bridge> rev 0x03 on pci0.1.0 > chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0 > ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1 > chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3 > vx0: <3COM 3C590 Etherlink III PCI> rev 0x00 int a irq 10 on pci0.14.0 > utp/aui/bnc[*utp*] address 00:a0:24:6c:23:66 > chip4: <PCI to PCI bridge (vendor=1011 device=0024)> rev 0x03 on > pci0.15.0 > Probing for devices on PCI bus 1: > vga0: <ATI model 4742 graphics accelerator> rev 0x5c int a irq 9 on > pci1.0.0 > Probing for devices on PCI bus 2: > ahc0: <Adaptec 2940 Ultra SCSI adapter> rev 0x00 int a irq 9 on pci2.9.0 > ahc0: aic7880 Single Channel A, SCSI Id=7, 16/255 SCBs > ahc1: <Adaptec 2940 Ultra SCSI adapter> rev 0x00 int a irq 14 on > pci2.10.0 > ahc1: aic7880 Single Channel A, SCSI Id=7, 16/255 SCBs > Probing for devices on the ISA bus: > sc0 on isa > sc0: VGA color <16 virtual consoles, flags=0x0> > ed0 not found at 0x280 > fe0 not found at 0x300 > atkbdc0 at 0x60-0x6f on motherboard > atkbd0 irq 1 on isa > psm0 not found > sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa > sio0: type 16550A > sio1 at 0x2f8-0x2ff irq 3 on isa > sio1: type 16550A > fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa > fdc0: FIFO enabled, 8 bytes threshold > fd0: 1.44MB 3.5in > wdc0 not found at 0x1f0 > wdc1 not found at 0x170 > wt0 not found at 0x300 > mcd0 not found at 0x300 > matcdc0 not found at 0x230 > scd0 not found at 0x230 > ppc0 at 0x378 irq 7 on isa > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > nlpt0: <generic printer> on ppbus 0 > nlpt0: Interrupt-driven port > ppi0: <generic parallel i/o> on ppbus 0 > plip0: <PLIP network interface> on ppbus 0 > ie0: unknown board_id: f000 > ie0 not found at 0x300 > ep0 not found at 0x300 > ex0 not found > le0 not found at 0x300 > lnc0 not found at 0x280 > ze0 not found at 0x300 > zp0 not found at 0x300 > cs0 not found at 0x300 > bt0 not found at 0x134 > aha0 not found at 0x134 > vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa > npx0 on motherboard > npx0: INT 16 interface > ccd0-3: Concatenated disk drivers > Waiting 5 seconds for SCSI devices to settle > changing root device to da0s1a > da1 at ahc0 bus 0 target 1 lun 0 > da1: <Quantum XP34300 L912> Fixed Direct Access SCSI-2 device > da1: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled > da1: 4101MB (8399520 512 byte sectors: 255H 63S/T 522C) > da5 at ahc1 bus 0 target 1 lun 0 > da5: <Quantum XP34300 L912> Fixed Direct Access SCSI-2 device > da5: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled > da5: 4101MB (8399520 512 byte sectors: 255H 63S/T 522C) > da4 at ahc1 bus 0 target 0 lun 0 > da4: <SEAGATE ST34555N 0930> Fixed Direct Access SCSI-2 device > da4: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled > da4: 4340MB (8888924 512 byte sectors: 255H 63S/T 553C) > da3 at ahc0 bus 0 target 3 lun 0 > da3: <CONNER CFP2107S 2.14GB 172B> Fixed Direct Access SCSI-2 device > da3: 10.0MB/s transfers (10.0MHz, offset 15) > da3: 2048MB (4194304 512 byte sectors: 255H 63S/T 261C) > da0 at ahc0 bus 0 target 0 lun 0 > da0: <MICROP 4110-09TBCU0322J HT01> Fixed Direct Access SCSI-2 device > da0: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled > da0: 1002MB (2053880 512 byte sectors: 64H 32S/T 1002C) > da2 at ahc0 bus 0 target 2 lun 0 > da2: <SEAGATE ST34555N 0930> Fixed Direct Access SCSI-2 device > da2: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled > da2: 4340MB (8888924 512 byte sectors: 255H 63S/T 553C) Next SCSI controller below ... > da6 at ahc1 bus 0 target 2 lun 0 > da6: <SEAGATE ST32155N 0594> Fixed Direct Access SCSI-2 device > da6: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled > da6: 2049MB (4197405 512 byte sectors: 255H 63S/T 261C) > da7 at ahc1 bus 0 target 4 lun 0 > da7: <IBM DDRS-39130 S97B> Fixed Direct Access SCSI-2 device > da7: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled > da7: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C) Doug White Internet: dwhite@resnet.uoregon.edu | FreeBSD: The Power to Serve http://gladstone.uoregon.edu/~dwhite | www.freebsd.org To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.03.9904301159520.16807-100000>