Date: Fri, 5 Dec 2008 10:44:02 -0800 From: Ji <lijimlee@gmail.com> To: freebsd-hardware@freebsd.org Subject: interrupt problem when enabling serial console Message-ID: <8fd8f02c0812051044u1e9cde4mbe47eb49c100c3c9@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
Hi all,
( I posted the following on freebsd-questions, and Mel suggested me to
post it here.)
I ran into a weird problem when enabling serial console on the
FreeBSD7.0. Your help is really appreciated.
I installed FreeBSD 7.0 amd64 (from the CD) on a Dell R200, and then
enabled the serial console by adding the following to
/boot/loader.conf
hint.sio.0.flags="0x30"
console="comconsole vidconsole"
comconsole_speed="9600"
boot_multicons="yes"
And also replaced the following line on /etc/ttys,
ttyd0 "/usr/libexec/getty std.9600" dialup off secure
with
ttyd0 "/usr/libexec/getty std.9600" vt220 on secure.
During rebooting, I found that the system hangs with the following
messages and actually all devices can NOT get interrupt resource (see
the attached message part 2 in the lower part of this email ).
"
...
Trying to mount root from ufs:/dev/ad4s1a
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:da0s1a
? List valid disk boot devices
<empty line> Abort manual input
..."
(I tried type ?, there is nothing)
And it confused me that if I keep rebooting again and again without
doing any fixing, the problem comes and goes. When the problem is not
present, the serial console works fine.
Below, I attached booting message 1) with disabling serial, 2) with
serial and problem showing up and 3) with serial and problem not
showing up.
Can anyone help me with that? Thanks a lot.
Jim
(The kernel configuration file is the original GENERIC on FBSD7 amd64
installation CD)
> =============== 1) dmesg without enabling serial console ===================
> Copyright (c) 1992-2008 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008
> root@driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Xeon(R) CPU E3110 @ 3.00GHz (3000.23-MHz K8-class CPU)
> Origin = "GenuineIntel" Id = 0x10676 Stepping = 6
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Features2=0x8e3fd<SSE3,RSVD2,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,<b19>>
> AMD Features=0x20100800<SYSCALL,NX,LM>
> AMD Features2=0x1<LAHF>
> Cores per package: 2
> usable memory = 2133360640 (2034 MB)
> avail memory = 2058694656 (1963 MB)
> ACPI APIC Table: <DELL PE_SC3 >
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> ioapic0: Changing APIC ID to 2
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 10:34:18)
> acpi0: <DELL PE_SC3> on motherboard
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> Timecounter "HPET" frequency 14318180 Hz quality 900
> cpu0: <ACPI CPU> on acpi0
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 613091f06000613
> device_attach: est0 attach returned 6
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> cpu1: <ACPI CPU> on acpi0
> est1: <Enhanced SpeedStep Frequency Control> on cpu1
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 613091f06000613
> device_attach: est1 attach returned 6
> p4tcc1: <CPU Frequency Thermal Control> on cpu1
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0xece0-0xecff mem 0xdfbc0000-0xdfbdffff,0xdfbe0000-0xdfbfffff irq 16
> at device 0.0 on pci1
> em0: Using MSI interrupt
> em0: Ethernet address: 00:15:17:37:11:06
> em0: [FILTER]
> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0xdce0-0xdcff mem 0xdfcc0000-0xdfcdffff,0xdfce0000-0xdfcfffff irq 16
> at device 0.0 on pci2
> em1: Using MSI interrupt
> em1: Ethernet address: 00:15:17:36:19:d4
> em1: [FILTER]
> pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
> pci3: <ACPI PCI bus> on pcib3
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x4201> mem 0xdfdf0000-0xdfdfffff irq 16 at device 0.0 on pci3
> miibus0: <MII bus> on bge0
> brgphy0: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> bge0: Ethernet address: 00:1e:c9:ff:58:48
> bge0: [ITHREAD]
> pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
> pci4: <ACPI PCI bus> on pcib4
> bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x4201> mem 0xdfef0000-0xdfefffff irq 17 at device 0.0 on pci4
> miibus1: <MII bus> on bge1
> brgphy1: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus1
> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> bge1: Ethernet address: 00:1e:c9:ff:58:49
> bge1: [ITHREAD]
> uhci0: <UHCI (generic) USB controller> port 0xbc60-0xbc7f irq 21 at
> device 29.0 on pci0
> uhci0: [GIANT-LOCKED]
> uhci0: [ITHREAD]
> usb0: <UHCI (generic) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <UHCI (generic) USB controller> port 0xbc80-0xbc9f irq 20 at
> device 29.1 on pci0
> uhci1: [GIANT-LOCKED]
> uhci1: [ITHREAD]
> usb1: <UHCI (generic) USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <UHCI (generic) USB controller> port 0xbca0-0xbcbf irq 21 at
> device 29.2 on pci0
> uhci2: [GIANT-LOCKED]
> uhci2: [ITHREAD]
> usb2: <UHCI (generic) USB controller> on uhci2
> usb2: USB revision 1.0
> uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
> uhub2: 2 ports with 2 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdfaffc00-0xdfafffff
> irq 21 at device 29.7 on pci0
> ehci0: [GIANT-LOCKED]
> ehci0: [ITHREAD]
> usb3: EHCI version 1.0
> usb3: companion controllers, 2 ports each: usb0 usb1 usb2
> usb3: <EHCI (generic) USB 2.0 controller> on ehci0
> usb3: USB revision 2.0
> uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
> uhub3: 6 ports with 6 removable, self powered
> umass0: <Sony DRX-810UL, class 0/0, rev 2.00/1.00, addr 2> on uhub3
> uhub4: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr 3> on uhub3
> uhub4: multiple transaction translators
> uhub4: 4 ports with 4 removable, self powered
> pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci5: <ACPI PCI bus> on pcib5
> vgapci0: <VGA-compatible display> port 0xcc00-0xccff mem
> 0xd0000000-0xd7ffffff,0xdfff0000-0xdfffffff irq 19 at device 5.0 on
> pci5
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH9 SATA300 controller> port
> 0xbc30-0xbc37,0xbc28-0xbc2b,0xbc38-0xbc3f,0xbc2c-0xbc2f,0xbc40-0xbc4f,0xbc50-0xbc5f
> irq 23 at device 31.2 on pci0
> atapci0: [ITHREAD]
> ata2: <ATA channel 0> on atapci0
> ata2: [ITHREAD]
> ata3: <ATA channel 1> on atapci0
> ata3: [ITHREAD]
> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
> fdc0: does not respond
> device_attach: fdc0 attach returned 6
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
> sio0: type 16550A
> sio0: [FILTER]
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
> fdc0: does not respond
> device_attach: fdc0 attach returned 6
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcb7ff,0xec000-0xeffff on
> isa0
> ppc0: cannot reserve I/O port range
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounters tick every 1.000 msec
> hptrr: no controller detected.
> ad4: 76293MB <WDC WD800AAJS-18TDA1 01.00A04> at ata2-master SATA300
> SMP: AP CPU #1 Launched!
> cd0 at umass-sim0 bus 0 target 0 lun 0
> cd0: <SONY DVD RW DRU-810A 2.0e> Removable CD-ROM SCSI-0 device
> cd0: 40.000MB/s transfers
> cd0: Attempt to query device size failed: NOT READY, Medium not present
> Trying to mount root from ufs:/dev/ad4s1a
>
> === 2) problematic booting After enabling serial (copied from serial console)=====
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008
> root@driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Xeon(R) CPU E3110 @ 3.00GHz (3000.22-MHz K8-class CPU)
> Origin = "GenuineIntel" Id = 0x10676 Stepping = 6
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Features2=0x8e3fd<SSE3,RSVD2,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,<b19>>
> AMD Features=0x20100800<SYSCALL,NX,LM>
> AMD Features2=0x1<LAHF>
> Cores per package: 2
> usable memory = 2133360640 (2034 MB)
> avail memory = 2058747904 (1963 MB)
> kbd1 at kbdmux0
> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 10:34:18)
> cpu0 on motherboard
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 613091f06000613
> device_attach: est0 attach returned 6
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> pcib0: <Host to PCI bridge> pcibus 0 on motherboard
> pci0: <PCI bus> on pcib0
> pcib1: <PCI-PCI bridge> irq 15 at device 1.0 on pci0
> pci1: <PCI bus> on pcib1
> em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0xece0-0xecff mem 0xdfbc0000-0xdfbdffff,0xdfbe0000-0xdfbfffff irq 15
> at device 0.0 on pci1
> em0: Unable to allocate bus resource: interrupt
> em0: Allocation of PCI resources failed
> device_attach: em0 attach returned 6
> pcib2: <PCI-PCI bridge> irq 15 at device 28.0 on pci0
> pci2: <PCI bus> on pcib2
> em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0xdce0-0xdcff mem 0xdfcc0000-0xdfcdffff,0xdfce0000-0xdfcfffff irq 15
> at device 0.0 on pci2
> em1: Unable to allocate bus resource: interrupt
> em1: Allocation of PCI resources failed
> device_attach: em1 attach returned 6
> pcib3: <PCI-PCI bridge> irq 15 at device 28.4 on pci0
> pci3: <PCI bus> on pcib3
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x4201> mem 0xdfdf0000-0xdfdfffff irq 15 at device 0.0 on pci3
> bge0: couldn't map interrupt
> device_attach: bge0 attach returned 6
> pcib4: <PCI-PCI bridge> irq 14 at device 28.5 on pci0
> pci4: <PCI bus> on pcib4
> bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x4201> mem 0xdfef0000-0xdfefffff irq 14 at device 0.0 on pci4
> bge1: couldn't map interrupt
> device_attach: bge1 attach returned 6
> uhci0: <UHCI (generic) USB controller> port 0xbc60-0xbc7f irq 11 at
> device 29.0 on pci0
> uhci0: Could not allocate irq
> device_attach: uhci0 attach returned 6
> uhci1: <UHCI (generic) USB controller> port 0xbc80-0xbc9f irq 10 at
> device 29.1 on pci0
> uhci1: Could not allocate irq
> device_attach: uhci1 attach returned 6
> uhci2: <UHCI (generic) USB controller> port 0xbca0-0xbcbf irq 11 at
> device 29.2 on pci0
> uhci2: Could not allocate irq
> device_attach: uhci2 attach returned 6
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdfaffc00-0xdfafffff
> irq 11 at device 29.7 on pci0
> ehci0: Could not allocate irq
> device_attach: ehci0 attach returned 6
> pcib5: <PCI-PCI bridge> at device 30.0 on pci0
> pci5: <PCI bus> on pcib5
> vgapci0: <VGA-compatible display> port 0xcc00-0xccff mem
> 0xd0000000-0xd7ffffff,0xdfff0000-0xdfffffff irq 5 at device 5.0 on
> pci5
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH9 SATA300 controller> port
> 0xbc30-0xbc37,0xbc28-0xbc2b,0xbc38-0xbc3f,0xbc2c-0xbc2f,0xbc40-0xbc4f,0xbc50-0xbc5f
> irq 6 at device 31.2 on pci0
> atapci0: unable to map interrupt
> device_attach: atapci0 attach returned 6
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcb7ff,0xec000-0xeffff on
> isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> fdc0: cannot reserve interrupt line
> ppc0: cannot reserve I/O port range
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
> sio0: type 16550A, console
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounter "TSC" frequency 3000222630 Hz quality 800
> Timecounters tick every 1.000 msec
> hptrr: no controller detected.
> Trying to mount root from ufs:/dev/ad4s1a
>
> Manual root filesystem specification:
> <fstype>:<device> Mount <device> using filesystem <fstype>
> eg. ufs:da0s1a
> ? List valid disk boot devices
> <empty line> Abort manual input
>
> mountroot> ?
>
> List of GEOM managed disk devices:
>
>
> Manual root filesystem specification:
> <fstype>:<device> Mount <device> using filesystem <fstype>
> eg. ufs:da0s1a
> ? List valid disk boot devices
> <empty line> Abort manual input
>
> mountroot> ufs:/dev/ad4s1a
> Trying to mount root from ufs:/dev/ad4s1a
>
> Manual root filesystem specification:
> <fstype>:<device> Mount <device> using filesystem <fstype>
> eg. ufs:da0s1a
> ? List valid disk boot devices
> <empty line> Abort manual input
>
> mountroot>
> panic: Root mount failed, startup aborted.
> cpuid = 0
> Uptime: 1s
> Cannot dump. No dump device defined.
> Automatic reboot in 15 seconds - press a key on the console to abort
> --> Press a key on the console to reboot,
> --> or switch off the system now.
> Rebooting...
>
> ==== 3) normal booting after enabling serial (copied from serial console)=========
> Copyright (c) 1992-2008 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 7.0-RELEASE #0: Sun Feb 24 10:35:36 UTC 2008
> root@driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Xeon(R) CPU E3110 @ 3.00GHz (3000.22-MHz K8-class CPU)
> Origin = "GenuineIntel" Id = 0x10676 Stepping = 6
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Features2=0x8e3fd<SSE3,RSVD2,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,<b19>>
> AMD Features=0x20100800<SYSCALL,NX,LM>
> AMD Features2=0x1<LAHF>
> Cores per package: 2
> usable memory = 2133360640 (2034 MB)
> avail memory = 2058694656 (1963 MB)
> ACPI APIC Table: <DELL PE_SC3 >
> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> ioapic0: Changing APIC ID to 2
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
> hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 10:34:18)
> acpi0: <DELL PE_SC3> on motherboard
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
> Timecounter "HPET" frequency 14318180 Hz quality 900
> cpu0: <ACPI CPU> on acpi0
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 613091f06000613
> device_attach: est0 attach returned 6
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> cpu1: <ACPI CPU> on acpi0
> est1: <Enhanced SpeedStep Frequency Control> on cpu1
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: cpu_vendor GenuineIntel, msr 613091f06000613
> device_attach: est1 attach returned 6
> p4tcc1: <CPU Frequency Thermal Control> on cpu1
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0xece0-0xecff mem 0xdfbc0000-0xdfbdffff,0xdfbe0000-0xdfbfffff irq 16
> at device 0.0 on pci1
> em0: Using MSI interrupt
> em0: Ethernet address: 00:15:17:37:11:06
> em0: [FILTER]
> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0xdce0-0xdcff mem 0xdfcc0000-0xdfcdffff,0xdfce0000-0xdfcfffff irq 16
> at device 0.0 on pci2
> em1: Using MSI interrupt
> em1: Ethernet address: 00:15:17:36:19:d4
> em1: [FILTER]
> pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
> pci3: <ACPI PCI bus> on pcib3
> bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x4201> mem 0xdfdf0000-0xdfdfffff irq 16 at device 0.0 on pci3
> miibus0: <MII bus> on bge0
> brgphy0: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> bge0: Ethernet address: 00:1e:c9:ff:58:48
> bge0: [ITHREAD]
> pcib4: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
> pci4: <ACPI PCI bus> on pcib4
> bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev.
> 0x4201> mem 0xdfef0000-0xdfefffff irq 17 at device 0.0 on pci4
> miibus1: <MII bus> on bge1
> brgphy1: <BCM5750 10/100/1000baseTX PHY> PHY 1 on miibus1
> brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
> 1000baseT-FDX, auto
> bge1: Ethernet address: 00:1e:c9:ff:58:49
> bge1: [ITHREAD]
> uhci0: <UHCI (generic) USB controller> port 0xbc60-0xbc7f irq 21 at
> device 29.0 on pci0
> uhci0: [GIANT-LOCKED]
> uhci0: [ITHREAD]
> usb0: <UHCI (generic) USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <UHCI (generic) USB controller> port 0xbc80-0xbc9f irq 20 at
> device 29.1 on pci0
> uhci1: [GIANT-LOCKED]
> uhci1: [ITHREAD]
> usb1: <UHCI (generic) USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <UHCI (generic) USB controller> port 0xbca0-0xbcbf irq 21 at
> device 29.2 on pci0
> uhci2: [GIANT-LOCKED]
> uhci2: [ITHREAD]
> usb2: <UHCI (generic) USB controller> on uhci2
> usb2: USB revision 1.0
> uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
> uhub2: 2 ports with 2 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdfaffc00-0xdfafffff
> irq 21 at device 29.7 on pci0
> ehci0: [GIANT-LOCKED]
> ehci0: [ITHREAD]
> usb3: EHCI version 1.0
> usb3: companion controllers, 2 ports each: usb0 usb1 usb2
> usb3: <EHCI (generic) USB 2.0 controller> on ehci0
> usb3: USB revision 2.0
> uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
> uhub3: 6 ports with 6 removable, self powered
> umass0: <Sony DRX-810UL, class 0/0, rev 2.00/1.00, addr 2> on uhub3
> uhub4: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/0.0b, addr 3> on uhub3
> uhub4: multiple transaction translators
> uhub4: 4 ports with 4 removable, self powered
> pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci5: <ACPI PCI bus> on pcib5
> vgapci0: <VGA-compatible display> port 0xcc00-0xccff mem
> 0xd0000000-0xd7ffffff,0xdfff0000-0xdfffffff irq 19 at device 5.0 on
> pci5
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel ICH9 SATA300 controller> port
> 0xbc30-0xbc37,0xbc28-0xbc2b,0xbc38-0xbc3f,0xbc2c-0xbc2f,0xbc40-0xbc4f,0xbc50-0xbc5f
> irq 23 at device 31.2 on pci0
> atapci0: [ITHREAD]
> ata2: <ATA channel 0> on atapci0
> ata2: [ITHREAD]
> ata3: <ATA channel 1> on atapci0
> ata3: [ITHREAD]
> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
> fdc0: does not respond
> device_attach: fdc0 attach returned 6
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x30 on acpi0
> sio0: type 16550A, console
> sio0: [FILTER]
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
> fdc0: does not respond
> device_attach: fdc0 attach returned 6
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcb7ff,0xec000-0xeffff on
> isa0
> ppc0: cannot reserve I/O port range
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> Timecounters tick every 1.000 msec
> hptrr: no controller detected.
> ad4: 76293MB <WDC WD800AAJS-18TDA1 01.00A04> at ata2-master SATA300
> SMP: AP CPU #1 Launched!
> cd0 at umass-sim0 bus 0 target 0 lun 0
> cd0: <SONY DVD RW DRU-810A 2.0e> Removable CD-ROM SCSI-0 device
> cd0: 40.000MB/s transfers
> cd0: Attempt to query device size failed: NOT READY, Medium not present
> Trying to mount root from ufs:/dev/ad4s1a
> Loading configuration files.
> kernel dumps on /dev/ad4s3b
> Entropy harvesting: interrupts ethernet point_to_point kickstart.
> swapon: adding /dev/ad4s3b as swap device
> Starting file system checks:
> /dev/ad4s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
> /dev/ad4s1a: clean, 12820246 free (58710 frags, 1595192 blocks, 0.4%
> fragmentation)
> Setting hostuuid: 44454c4c-3400-1053-8059-b7c04f484831.
> Setting hostid: 0x0188e958.
> Mounting local file systems:.
> Setting hostname: .fastsoft.com.
> net.inet6.ip6.auto_linklocal: 1 -> 0
> bge0: link state changed to DOWN
> bge0: no link .....bge0: link state changed to UP
> got link
> DHCPREQUEST on bge0 to 255.255.255.255 port 67
> DHCPACK from 172.16.0.22
> bound to 172.16.1.16 -- renewal in 345600 seconds.
> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
> inet6 ::1 prefixlen 128
> inet 127.0.0.1 netmask 0xff000000 b
> bge0: flags=884g3<UP,BROADCAST,ReUNNING,SIMPLEX,M1ULTICAST> metric: 0 mtu 1500
> op tions=9b<RXCSUM,lTXCSUM,VLAN_MTU,iVLAN_HWTAGGING,VnLAN_HWCSUM>
> etkher 00:1e:c9:ff: 58:48
> inet 172s.16.1.16 netmaskt 0xffff0000 broaadcast 172.16.255t.255
> media: Etehernet autoselec t (1000baseTX <fcull-duplex>)
> shtatus: active
> aAdditional routinng options:.
> Stgarting devd.
> ed to UP
> hw.acpi.cpu.cx_lowest: C1
> sysctl: hw.acpi.cpu.cx_lowest: Invalid argument
> Additional IP options:.
> Mounting NFS file systems:.
> Creating and/or trimming log files:.
> Starting syslogd.
> Checking for core dump on /dev/ad4s3b...
> savecore: no dumps found
> ELF ldconfig path: /lib /usr/lib /usr/lib/compat
> 32-bit compatibility ldconfig path:
> Initial amd64 initialization:.
> Additional ABI support:.
> Clearing /tmp (X related).
> Starting local daemons:.
> Updating motd.
> Mounting late file systems:.
> Configuring syscons: blanktime.
> Starting sshd.
> Starting cron.
> Local package initialization:.
> Starting background file system checks in 60 seconds.
>
> Tue Dec 2 16:58:50 UTC 2008
>
> FreeBSD/amd64 (xxxxx) (ttyd0)
>
> login:
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?8fd8f02c0812051044u1e9cde4mbe47eb49c100c3c9>