From owner-freebsd-hardware Fri Oct 18 10:54:58 2002 Delivered-To: freebsd-hardware@freebsd.org Received: from mx1.FreeBSD.org (mx1.freebsd.org [216.136.204.125]) by hub.freebsd.org (Postfix) with ESMTP id F20CD37B401 for ; Fri, 18 Oct 2002 10:54:55 -0700 (PDT) Received: from sccimhc01.insightbb.com (sccimhc01.insightbb.com [63.240.76.163]) by mx1.FreeBSD.org (Postfix) with ESMTP id 4BD2343E4A for ; Fri, 18 Oct 2002 10:54:55 -0700 (PDT) (envelope-from bryanc2000@Insightbb.com) Received: from insightbb.com ([12.222.162.255]) by sccimhc01.insightbb.com (InterMail vM.4.01.03.27 201-229-121-127-20010626) with SMTP id <20021018175450.XILO5019.sccimhc01.insightbb.com@insightbb.com>; Fri, 18 Oct 2002 17:54:50 +0000 Date: Fri, 18 Oct 2002 10:54:51 -0500 From: Bryan Cassidy To: freebsd-hardware Cc: Mike Nowlin Subject: Re: Zip Drive Message-Id: <20021018105451.25f13d52.bryanc2000@Insightbb.com> In-Reply-To: <1034925511.11555.81.camel@jason> References: <20021017235145.4b0b0ff6.bryanc2000@Insightbb.com> <1034925511.11555.81.camel@jason> X-Mailer: Sylpheed version 0.8.5 (GTK+ 1.2.10; i386-portbld-freebsd4.6.2) Mime-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit Sender: owner-freebsd-hardware@FreeBSD.ORG Precedence: bulk List-ID: List-Archive: (Web Archive) List-Help: (List Instructions) List-Subscribe: List-Unsubscribe: X-Loop: FreeBSD.org On 18 Oct 2002 03:18:31 -0400 Mike Nowlin wrote: > First question - what kind of Zip drive? There's about a billion > versions of them out there. IDE? USB? SCSI? And what capacity? > > I have both the IDE and SCSI 100MB versions - the SCSI one shows up as a > plain-jane SCSI device upon bootup. (The IDE one does as well under > Linux, but I haven't tried it under FreeBSD.) Basically, you treat them > as standard hard drives, assuming that you use caution when it comes to > the "removable" aspect of things... > > As far as the USB versions, I'd guess that they're probably supported by > the umass driver, but that's just a guess... > > Sending your "dmesg" output would probably be helpful... > > mike > Ok. Sorry it took so long to reply. I am using a Iomega Zip 250 thats IDE. Its about 3 years old or so. and here is my output from dmesg bryanc2000@insightbb [10:54] [/home/bryanc2000] ===>dmesg Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.6.2-RELEASE #0: Fri Oct 18 00:27:40 CDT 2002 bryanc2000@insightbb.com:/usr/obj/usr/src/sys/HAL Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (748.28-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x681 Stepping = 1 Features=0x383f9ff real memory = 402653184 (393216K bytes) config> di sn0 config> di lnc0 config> di ie0 config> di fe0 config> di ed0 config> di cs0 config> q avail memory = 387244032 (378168K bytes) Preloaded elf kernel "kernel" at 0xc0426000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc042609c. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 10 entries at 0xc00fdf20 npx0: on motherboard npx0: INT 16 interface pcib0: on motherboard pci0: on pcib0 pcib1: at device 1.0 on pci0 pci1: on pcib1 pci1: at 0.0 irq 11 isab0: at device 7.0 on pci0 isa0: on isab0 atapci0: port 0x1400-0x140f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: port 0x10c0-0x10df irq 9 at device 7.2 on pci0 usb0: on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ums0: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), rev 1.10/3.00, addr 2, iclass 3/1 ums0: 5 buttons and Z dir. chip1: port 0x7000-0x700f at device 7.3 on pci0 pcm0: port 0x10e0-0x10ff irq 10 at device 14.0 on pci0 atapci1: port 0x1080-0x10bf,0x1418-0x141b,0x1420-0x1427,0x141c-0x141f,0x1428-0x142f mem 0xe8020000-0xe803ffff irq 3 at device 15.0 on pci0 ata2: at 0x1428 on atapci1 ata3: at 0x1420 on atapci1 pci0: (vendor=0x14f1, dev=0x1066) at 16.0 irq 9 xl0: <3Com 3c900B-TPO Etherlink XL> port 0x1000-0x107f mem 0xe8010000-0xe801007f irq 3 at device 17.0 on pci0 xl0: Ethernet address: 00:01:02:86:2d:ce xl0: selecting 10baseT transceiver, half duplex orm0: