Date: Tue, 6 Feb 2007 19:18:51 -0800 (PST) From: Nicole Harrington <drumslayer2@yahoo.com> To: Mike Tancsa <mike@sentex.net> Cc: freebsd-questions@freebsd.org Subject: Re: Problem with Serverworks HT1000 serial ATA support - Tyan S3992 Motherboard Message-ID: <75026.74951.qm@web34512.mail.mud.yahoo.com> In-Reply-To: <jgdis250dn0lm13f0g61khevmq9fjqtkr3@4ax.com>
next in thread | previous in thread | raw e-mail | index | archive | help
--- Mike Tancsa <mike@sentex.net> wrote: > On Tue, 6 Feb 2007 15:26:27 -0800 (PST), in > sentex.lists.freebsd.questions you wrote: > > If I run: bonnie++ -d /home -u root s1g > > The system reboots. > > > > I have tried this is both S-ATA and P-ATA > emulation. > >atapci0: <ServerWorks HT1000 SATA150 controller> > port > >0xb080-0xb087,0xb000-0xb003,0xac00-0xac07 > >,0xa880-0xa883,0xa800-0xa81f mem > 0xff4fe000-0xff4fffff > >irq 11 at device 14.0 on pci1 > > > >S-ATA: > >ad4: 70911MB <WDC WD740ADFD-00NLR1 20.07P20> at > >ata2-master SATA150 > > > > OR > >P-ATA: > >ad4: DMA limited to UDMA33, device found non-ATA66 > >cable > >ad4: 70911MB <WDC WD740ADFD-00NLR1 20.07P20> at > >ata2-master UDMA33 > I use RELENG_6 in i386 mode on this MB (two > integrated em nics) and it > works quite well Have you tried it with the tune for Diskd mentioned. > atapci0: <ServerWorks HT1000 SATA150 controller> > port > 0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb81f > mem 0xff > 3fe000-0xff3fffff irq 11 at device 14.0 on pci1 > ata2: <ATA channel 0> on atapci0 > ata3: <ATA channel 1> on atapci0 > ata4: <ATA channel 2> on atapci0 > ata5: <ATA channel 3> on atapci0 > atapci1: <ServerWorks HT1000 UDMA100 controller> > port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at > device 2.1 on > pci0 > ata0: <ATA channel 0> on atapci1 > ata1: <ATA channel 1> on atapci1 > > ad4: 76319MB <Seagate ST380811AS 3.AAE> at > ata2-master SATA150 > > # atacontrol list > ATA channel 0: > Master: no device present > Slave: no device present > ATA channel 1: > Master: no device present > Slave: no device present > ATA channel 2: > Master: ad4 <ST380811AS/3.AAE> Serial ATA II > Slave: no device present > ATA channel 3: > Master: no device present > Slave: no device present > ATA channel 4: > Master: no device present > Slave: no device present > ATA channel 5: > Master: no device present > Slave: no device present > > > However, update the BIOS and make sure you dont use > PATA emulation on > the SATA controller as that doesnt really work. > > ---Mike > -------------------------------------------------------- > Mike Tancsa, Sentex communications > http://www.sentex.net > Providing Internet Access since 1994 > mike@sentex.net, (http://www.tancsa.com) Hi Mike Yes, it does work quite well. But not if I use the same tuning parameters used on systems running on Non Serverworks chipsets. (Tyan S2881 or S2882 Board) I use these for supporting many heavy loaded Squid servers. The normal tweaks suggested for Squid, and work well on Non Serverworks chipsets are: /boot/loader.conf kern.ipc.maxsockets=16424 kern.ipc.msgmnb=16384 kern.ipc.msgmni=41 kern.ipc.msgseg=2049 kern.ipc.msgssz=64 kern.ipc.msgtql=2048 OR kern.ipc.msgmnb=8192 kern.ipc.msgmni=40 kern.ipc.msgseg=512 kern.ipc.msgssz=64 kern.ipc.msgtql=1024 However, with any setting of kern.ipc.msgtql (What does it do anyway?) above 64 the server crashes with the Bonnie test. The higher the setting the faster the crash. Nicole
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?75026.74951.qm>