Date: Mon, 18 Sep 2000 22:38:44 +0800 (SGT) From: Chan Tur Wei <twchan@singnet.com.sg> To: freebsd-stable@freebsd.org Subject: csa device hangs my laptop at boot time Message-ID: <Pine.BSF.4.21.0009182230460.11004-400000@zaapth.twnet.org> In-Reply-To: <4.3.2.7.2.20000918170323.00aa6210@pop.singnet.com.sg>
next in thread | previous in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Hi,
My most recent CVSup (Mon Sep 18 03:27:06 SGT 2000 (which is GMT+8)) of
4.1-Stable is causing me grief with the csa device. Following the UPDATING
procedure religiously, which has always been working A-OK, I do:
make buildworld
make buildkernel KERNEL=ZARGKERNEL
make installkernel KERNEL=ZARGKERNEL
[reboot laptop]
After the reboot, the system kernel probes the pcic-pci0 and pcic-pci1
devices, and then the csa0 device:
chip1: <Intel 82371AB Power management controller> port 0x1400-0x140f at
device 7.3 on pci0
pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> irq 10 at device 8.0 on pci0
pcic-pci0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> irq 10 at device 8.1 on pci0
pcic-pci1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
csa0: <Crystal Semiconductor CS4614/4622/4624 Audio accelerator/4280 Audio
controller> mem 0xe9000000-0xe90fffff,0xe8000000-0xe8000fff irq 5 at device 9.0 on pci0
and then locks up right there. No panic, no nothing. If I modify my
kernel config and take out the pcm device and csa device, the kernel boots
fine. Seeing as to how no one else has reported a similar problem, are
there any suggestions on how I should go about cracking this problem? For
a start, I've (verbosely) included (a) hung.console.txt, which is the text
I see on my screen (typed out) when I boot -v; (b) dmesg.GENERIC, which is
the dmesg output from booting the generic 4.1-R kernel, and (c) ZARGKERNEL,
my kernel config.
I hope to get the csa device back... oh yes, previous to these recent
CVSup's, the csa has been mostly okay.
Thanks for any help.
Regards
-T.W.Chan-
[-- Attachment #2 --]
pcic-pci1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
PCI Config space:
00: ac1c104c 02100007 06070001 00820000
10: 00000000 020000a0 00000000 00000000
20: 00000000 00000000 00000000 00000000
30: 00000000 00000000 00000000 03c0010a
40: ac1c1071 000003e1 00000000 00000000
50: 00000000 00000000 00000000 00000000
60: 00000000 00000000 00000000 00000000
70: 00000000 00000000 00000000 00000000
80: 2044b060 00000000 00000000 01dc1622
90: 606402c0 00000000 00000000 00000000
Cardbus Socket registers:
00: 00000000: 00000000: f000e2c3: f000c899:
10: 00000000: f000ff54: f000c899: f000c89a:
ExCa registers:
00: eb 88 d5 43 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03
10: 00 00 fb 77 44 86 c4 c0 c8 02 08 e8 40 91 88 fe
20: 28 e0 8a 66 02 38 e0 72 02 88 e0 bf 05 00 c4 5e
30: 04 50 b4 02 cd 13 5b 73 0a 4f 74 1c 30 e4 cd 13
csa0: <Crystal Semiconductor CS4614/4622/4624 Audio accelerator/4280 Audio controller> mem 0xe9000000-0xe90fffff,0xe8000000-0xe8000fff irq 5 at device 9.0 on pci0
[-- Attachment #3 --]
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Fri Jul 28 14:30:31 GMT 2000
jkh@ref4.freebsd.org:/usr/src/sys/compile/GENERIC
Calibrating clock(s) ... TSC clock: 331861952 Hz, i8254 clock: 1193296 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (331.83-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 100597760 (98240K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00426000 - 0x05fe7fff, 96215040 bytes (23490 pages)
avail memory = 93622272 (91428K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00e8050
bios32: Entry = 0xeb170 (c00eb170) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x31b0
pnpbios: Found PnP BIOS data at 0xc00ff020
pnpbios: Entry = ec000:2fb2 Rev = 1.0
pnpbios: OEM ID 8224744e
Other BIOS signatures found:
ACPI: 000f0010
Preloaded elf kernel "kernel.old" at 0xc040d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base 20000000, size 28
found-> vendor=0x8086, dev=0x7191, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 00001100, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=128
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00001400, size 4
found-> vendor=0x104c, dev=0xac1c, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
found-> vendor=0x104c, dev=0xac1c, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=10
found-> vendor=0x1013, dev=0x6003, revid=0x01
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base e8000000, size 12
map[14]: type 1, range 32, base e9000000, size 20
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x1002, dev=0x4c42, revid=0xdc
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 1, range 32, base e4000000, size 24
map[14]: type 1, range 32, base 0000d000, size 8
map[18]: type 1, range 32, base e6000000, size 12
pci1: <PCI bus> on pcib1
pci1: <ATI model 4c42 graphics accelerator> (vendor=0x1002, dev=0x4c42) at 0.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1100-0x110f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1100
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1108
ata1: mask=03 status0=50 status1=01
ata1: mask=03 status0=00 status1=01
ata1: devices = 0xc
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 128 at device 7.2 on pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6
chip1: <Intel 82371AB Power management controller> port 0x1400-0x140f at device 7.3 on pci0
pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> irq 10 at device 8.0 on pci0
pcic-pci0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pcic-pci0: Legacy address set to 0x3e0
PCI Config space:
00: ac1c104c 02100007 06070001 00820000
10: 00000000 020000a0 00000000 00000000
20: 00000000 00000000 00000000 00000000
30: 00000000 00000000 00000000 03c0010a
40: ac1c1071 000003e1 00000000 00000000
50: 00000000 00000000 00000000 00000000
60: 00000000 00000000 00000000 00000000
70: 00000000 00000000 00000000 00000000
80: 20449060 00000000 00000000 01dc1622
90: 606402c0 00000000 00000000 00000000
Cardbus Socket registers:
00: 00000000: 00000000: f000e2c3: f000c899:
10: 00000000: f000ff54: f000c899: f000c89a:
ExCa registers:
00: eb 88 d5 43 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03
10: 00 00 fb 77 44 86 c4 c0 c8 02 08 e8 40 91 88 fe
20: 28 e0 8a 66 02 38 e0 72 02 88 e0 bf 05 00 c4 5e
30: 04 50 b4 02 cd 13 5b 73 0a 4f 74 1c 30 e4 cd 13
pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> irq 10 at device 8.1 on pci0
pcic-pci1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
PCI Config space:
00: ac1c104c 02100007 06070001 00820000
10: 00000000 020000a0 00000000 00000000
20: 00000000 00000000 00000000 00000000
30: 00000000 00000000 00000000 03c0010a
40: ac1c1071 000003e1 00000000 00000000
50: 00000000 00000000 00000000 00000000
60: 00000000 00000000 00000000 00000000
70: 00000000 00000000 00000000 00000000
80: 20449060 00000000 00000000 01dc1622
90: 606402c0 00000000 00000000 00000000
Cardbus Socket registers:
00: 00000000: 00000000: f000e2c3: f000c899:
10: 00000000: f000ff54: f000c899: f000c89a:
ExCa registers:
00: eb 88 d5 43 30 d2 66 f7 f3 88 d7 5a 66 3d ff 03
10: 00 00 fb 77 44 86 c4 c0 c8 02 08 e8 40 91 88 fe
20: 28 e0 8a 66 02 38 e0 72 02 88 e0 bf 05 00 c4 5e
30: 04 50 b4 02 cd 13 5b 73 0a 4f 74 1c 30 e4 cd 13
pci0: <unknown card> (vendor=0x1013, dev=0x6003) at 9.0 irq 5
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 1a 03 3c
psm: status 1a 03 3c
psm: status 1a 03 3c
psm: data c8 c6 51
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0-51, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 53 84
b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 53 84
b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f
b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 irq 10 on isa0
pcic0: management irq 10
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
isa_compat: didn't get irq for lnc
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fdfe3f 0..1021=1022 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03ff0001 0..1023=1024 cylinders, 0..0=1 heads, 1..1=1 sectors
2:03ff0001 0..1023=1024 cylinders, 0..0=1 heads, 1..1=1 sectors
3:03ff0001 0..1023=1024 cylinders, 0..0=1 heads, 1..1=1 sectors
0 accounted for
Device configuration finished.
RTC BIOS diagnostic error 20<config_unit>
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio 68c040, tty 63109a, net 67109a
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: faith0 attached
pccard: card inserted, slot 1
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ata0-master: success setting up UDMA2 mode on PIIX4 chip
ad0: <IBM-DARA-212000/AR4OA51A> ATA-4 disk at ata0 as master
ad0: 11513MB (23579136 sectors), 23392 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
Creating DISK ad0
Creating DISK wd0
ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata1-master: success setting up PIO4 mode on generic chip
acd0: <CD-224E/1.0A> CDROM drive at ata1 as master
acd0: read 4134KB/s (4134KB/s), 512KB buffer, PIO4
acd0: Reads: CD-R, CD-DA stream
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: CD-ROM 120mm data disc loaded, unlocked
Mounting root from ufs:/dev/ad0s2a
ad0s1: type 0xb, start 63, end = 12289724, size 12289662 : OK
ad0s2: type 0xa5, start 12289725, end = 23567354, size 11277630 : OK
start_init: trying /sbin/init
Linux-ELF exec handler installed
splash: image decoder found: fade_saver
xe0 at port 0x2e8-0x2ef iomem 0xd0000-0xd0fff irq 11 slot 1 on pccard1
pcic: I/O win 1 flags 17 100-10f
xe0: Xircom CEM56, bonding version 0x55, 100Mbps capable, with modem
xe0: DingoID = 0x444b, RevisionID = 0x1, VendorID = 0
xe0: Ethernet address 00:10:a4:e3:a5:b9
bpf: xe0 attached
xe0: watchdog timeout; resetting card
[-- Attachment #4 --]
#
# ZARGKERNEL
machine i386
ident ZARGKERNEL
maxusers 32
makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
#####################################################################
# SMP OPTIONS:
#
#####################################################################
# CPU OPTIONS
cpu I586_CPU # aka Pentium(tm)
cpu I686_CPU # aka Pentium Pro(tm)
options NO_F00F_HACK
#####################################################################
# COMPATIBILITY OPTIONS
options COMPAT_43
options USER_LDT #allow user-level control of i386 ldt
options SYSVSHM
options SYSVSEM
options SYSVMSG
#####################################################################
# DEBUGGING OPTIONS
options DDB
options KTRACE #kernel tracing
options UCONSOLE
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
#####################################################################
# NETWORKING OPTIONS
options INET #Internet communications protocols
#options INET6 #IPv6 communications protocols
#options IPX #IPX/SPX communications protocols
#options NCP #NetWare Core protocol
#
# Network interfaces:
pseudo-device ether #Generic Ethernet
pseudo-device loop #Network loopback device
pseudo-device bpf #Berkeley packet filter
pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
pseudo-device sl 1 #Serial Line IP
pseudo-device ppp 1 #Point-to-point protocol
#pseudo-device ef # Multiple ethernet frames support
#options ETHER_II # enable Ethernet_II frame
#options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
#options ETHER_8022 # enable Ethernet_802.2 frame
#options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
# for IPv6
#pseudo-device gif 4 #IPv6 and IPv4 tunneling
#pseudo-device faith 1 #for IPv6 and IPv4 translation
#
# Internet family options:
#
#options IPFIREWALL #firewall
#options IPFIREWALL_VERBOSE #print information about
# dropped packets
#options IPFIREWALL_FORWARD #enable transparent proxy support
#options IPDIVERT #divert sockets
#options IPFILTER #ipfilter support
options ICMP_BANDLIM
#####################################################################
# FILESYSTEM OPTIONS
options FFS #Fast filesystem
options NFS #Network File System
options CD9660 #ISO 9660 filesystem
options KERNFS #Kernel filesystem
options MSDOSFS #MS DOS File System
#options NWFS #NetWare filesystem
options PROCFS #Process filesystem
options CD9660_ROOT #CD-ROM usable as root device
options FFS_ROOT #FFS usable as root device
options SOFTUPDATES
#options EXT2FS
#####################################################################
# POSIX P1003.1B
options P1003_1B
options _KPOSIX_PRIORITY_SCHEDULING
#####################################################################
# SCSI DEVICES
#device scbus #base SCSI code
#####################################################################
# MISCELLANEOUS DEVICES AND OPTIONS
pseudo-device pty #Pseudo ttys
pseudo-device speaker #Play IBM BASIC-style noises out your speaker
pseudo-device gzip #Exec gzipped a.out's
pseudo-device vn #Vnode driver (turns a file into a device)
pseudo-device md #Memory/malloc disk
#####################################################################
# HARDWARE DEVICE CONFIGURATION
device isa
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
options PSM_HOOKRESUME #hook the system resume event, useful
#for some laptops
options PSM_RESETAFTERSUSPEND #reset the device at the resume event
device vga0 at isa?
options VESA
pseudo-device splash
device sc0 at isa?
options SC_HISTORY_SIZE=500 # number of history buffer lines
# The following options will let you change the default colors of syscons.
#options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
#options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
#options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
#options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
device npx0 at nexus? port IO_NPX flags 0x0 irq 13
#
# Optional ISA and EISA devices:
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
#device ata0 at isa? port IO_WD1 irq 14
#device ata1 at isa? port IO_WD2 irq 15
#device wdc0 at isa? port IO_WD1 irq 14
#device wd0 at wdc0 drive 0
#device wd1 at wdc0 drive 1
#device wdc1 at isa? port IO_WD2 irq 15
#device wd2 at wdc1 drive 0
#device wd3 at wdc1 drive 1
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
#device fd1 at fdc0 drive 1
#
# Other standard PC hardware: `mse', `sio', etc.
#
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
#
# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
#
device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
device xe0
#
# ATM related options
#
#
# Audio drivers: `snd', `sb', `pas', `gus', `pca'
device pcm
# device csa0 at isa? port 0x220 irq 5 drq 1 flags 0x13
device pca0 at isa? port IO_TIMER1
#device sbc0 at isa? port 0x220 irq 5 drq 1 flags 0x15
device csa0
#
# Miscellaneous hardware:
#
device apm0
device joy0 at isa? port IO_GAME
#
# MCA devices:
#
#
# EISA devices:
#
#
# PCI devices & PCI options:
#
device pci
device miibus
device vr # VIA Rhine, Rhine II
device de # DEC/Intel DC21x4x (``Tulip'')
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device tx # SMC 9432TX (83c170 ``EPIC'')
#
# PCCARD/PCMCIA
#
device pcic0 at isa?
device pcic1 at isa?
device card
options PCIC_RESUME_RESET # reset after resume
#
# Laptop/Notebook options:
#
#
# SMB bus
#
#
# I2C Bus
#
# Parallel-Port Bus
#
device ppc0 at isa? irq 7
device ppbus
device lpt
device plip
device ppi
# USB support
# UHCI controller
device uhci
# OHCI controller
device ohci
# General USB code (mandatory for USB)
device usb
#
# Generic USB device driver
device ugen
device uhid # Human Interface Device
device ukbd # USB keyboard
device ulpt # USB printer
# device umass # USB Iomega Zip 100 Drive
device ums # USB mouse
# debugging options for the USB subsystem
#
options UHCI_DEBUG
options OHCI_DEBUG
options USB_DEBUG
options UGEN_DEBUG
options UHID_DEBUG
options UHUB_DEBUG
options UKBD_DEBUG
options ULPT_DEBUG
# options UMASS_DEBUG
options UMS_DEBUG
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0009182230460.11004-400000>