From owner-freebsd-questions Tue Jan 26 19:09:11 1999 Return-Path: Received: (from majordom@localhost) by hub.freebsd.org (8.8.8/8.8.8) id TAA14131 for freebsd-questions-outgoing; Tue, 26 Jan 1999 19:09:11 -0800 (PST) (envelope-from owner-freebsd-questions@FreeBSD.ORG) Received: from uhura.concentric.net (uhura.concentric.net [206.173.119.93]) by hub.freebsd.org (8.8.8/8.8.8) with ESMTP id TAA14126 for ; Tue, 26 Jan 1999 19:09:08 -0800 (PST) (envelope-from ehm@concentric.net) Received: from cliff.concentric.net ([206.173.119.90]) by uhura.concentric.net (8.9.1a/(98/12/15 5.12)) id WAA05672; Tue, 26 Jan 1999 22:08:54 -0500 (EST) [1-800-745-2747 The Concentric Network] Received: from nomad.gte.com (ts013d47.dal-tx.concentric.net [206.173.142.155]) by cliff.concentric.net (8.9.1a) id WAA07503; Tue, 26 Jan 1999 22:08:52 -0500 (EST) Message-ID: <002c01be49a2$5e936480$2f5b5b8f@nomad.gte.com> From: "Erik Moe" To: Subject: 3.0-RELEASE install problems Date: Tue, 26 Jan 1999 21:08:36 -0600 MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit X-Priority: 3 X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook Express 4.72.3110.5 X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3110.3 Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG I'm getting the following error trying to do a CDROM install of 3.0-RELEASE on an HP Vectra 486/33u with an Adaptec 1740, SCSI Disk and SCSI CDROM: No CDROM devices found! Please check that your system's configuration is correct and that the CDROM drive is of a supported type. For more information, consult the hardware guide in the Doc menu. However, the CDROM appears to be detected at boot: avail memory = 4853760 (4740K bytes) eisa0: Probing for devices on the EISA bus ahb0: at 0x1c00-0x1cff irq 11 on eisa0 slot 1 ahb0: AHA1740 Single Ended SCSI Adapter, FW Rev. E , ID=7, 64 ECBs Probing for devices on the ISA bus: video#0: WARNING: video mode switching is not fully supported on this adapter sc0 at 0x60-0x6f irq 1 on motherboard sc0: VGA color <4 virtual consoles, flags=0x0> ed0 at 0x300-0x30f irq 5 maddr 0xcc000 msize 8192 on isa ed0: address 02:60:8c:da:9a:f6, type 3c503 (16 bit) sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A lpt0 at 0x378-0x37f irq 7 on isa lpt0: Interrupt-driven port lp0: TCP/IP capable interface fdc0 at 0x3f0-03f7 irq 6 drq 2 on isa fdc0: FIFO enabled, 8 bytes threshold fd0: 1.44MB 3.5in aha0: not found at 0x134 npx0 on motherboard npx0: INT 16 interface Waiting 15 seconds for SCSI devices to settle ahb0: SCSI Bus Reset Delivered da0 at ahb0 bus 0 target 0 lun 0 da0: Fixed Direct Access SCSI2 device da0: Tagged Queueing Enabled da0: 406MB (832527 512 byte sectors: 64H 32S/T 406C) cd0 at ahb0 bus 0 target 1 lun 0 cd0: Removable CD-ROM SCSI2 device cd0: cd present [1075534577 x 1415061573 byte records] changing root device to fd0c rootfs is 1440 Kbyte compiled in MFS /stand/sysinstall running as init on vty0 I tried to use the "fixit" floppy to gain further insight, but I have been unsuccessful in getting sysinstall to load the "fixit" floppy. This same system works fine with 2.2.8-RELEASE. Any suggestions or comments would be welcome. Please be sure to "cc" my email address since I don't subscribe to freebsd-questions. Erik Moe ehm@concentric.net To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message