Date: Sat, 1 May 1999 10:59:50 +0200 From: Gunnar Flygt <gunnar@pluto.sr.se> To: Doug White <dwhite@resnet.uoregon.edu> Cc: FreeBSD Questions <freebsd-questions@FreeBSD.org> Subject: Re: Adding SCSI-disks results in failure - adding dmesg Message-ID: <19990501105950.A87391@sr.se> In-Reply-To: <Pine.BSF.4.03.9904301159520.16807-100000@resnet.uoregon.edu>; from Doug White on Fri, Apr 30, 1999 at 12:02:17PM -0700 References: <19990429120138.A80213@sr.se> <Pine.BSF.4.03.9904301159520.16807-100000@resnet.uoregon.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, Apr 30, 1999 at 12:02:17PM -0700, Doug White wrote:
> On Thu, 29 Apr 1999, Gunnar Flygt wrote:
>
> > I didn't have the dmesg output when I wrote the first message I'll
> > append it on the end here including the error message.
>
> Please describe the SCSI chain before and after you connect the CDROM.
Actually, the CD-problems was someone else talking about. We have no CD
on this machine, just disks.
>
> > First here is the errro message:
> > bash-2.02# newfs /dev/da7s1a
> > newfs: /dev/da7s1a: Device not configured
>
> Try running '/dev/MAKEDEV da7'.
Already done, no difference.
>
> I'll leave the dmesg on, minus the INN problems.
>
> > And then dmesg output:
> > Copyright (c) 1992-1999 FreeBSD Inc.
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > The Regents of the University of California. All rights
> > reserved.
> > FreeBSD 3.1-RELEASE #0: Wed Apr 28 14:54:35 CEST 1999
> > root@news.sr.se:/usr/src/sys/compile/HOCKEY
> > Timecounter "i8254" frequency 1193182 Hz
> > CPU: Pentium II/Xeon/Celeron (349.13-MHz 686-class CPU)
> > Origin = "GenuineIntel" Id = 0x652 Stepping=2
> > +Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT
> > +,PSE36,MMX,<b24>>
> > real memory = 268435456 (262144K bytes)
> > avail memory = 257941504 (251896K bytes)
> > Preloaded elf kernel "kernel" at 0xf0336000.
> > Probing for devices on PCI bus 0:
> > chip0: <Intel 82443BX host to PCI bridge> rev 0x03 on pci0.0.0
> > chip1: <Intel 82443BX host to AGP bridge> rev 0x03 on pci0.1.0
> > chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0
> > ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
> > chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3
> > vx0: <3COM 3C590 Etherlink III PCI> rev 0x00 int a irq 10 on pci0.14.0
> > utp/aui/bnc[*utp*] address 00:a0:24:6c:23:66
> > chip4: <PCI to PCI bridge (vendor=1011 device=0024)> rev 0x03 on
> > pci0.15.0
> > Probing for devices on PCI bus 1:
> > vga0: <ATI model 4742 graphics accelerator> rev 0x5c int a irq 9 on
> > pci1.0.0
> > Probing for devices on PCI bus 2:
> > ahc0: <Adaptec 2940 Ultra SCSI adapter> rev 0x00 int a irq 9 on pci2.9.0
> > ahc0: aic7880 Single Channel A, SCSI Id=7, 16/255 SCBs
> > ahc1: <Adaptec 2940 Ultra SCSI adapter> rev 0x00 int a irq 14 on
> > pci2.10.0
> > ahc1: aic7880 Single Channel A, SCSI Id=7, 16/255 SCBs
> > Probing for devices on the ISA bus:
> > sc0 on isa
> > sc0: VGA color <16 virtual consoles, flags=0x0>
> > ed0 not found at 0x280
> > fe0 not found at 0x300
> > atkbdc0 at 0x60-0x6f on motherboard
> > atkbd0 irq 1 on isa
> > psm0 not found
> > sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
> > sio0: type 16550A
> > sio1 at 0x2f8-0x2ff irq 3 on isa
> > sio1: type 16550A
> > fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa > > fdc0: FIFO enabled, 8 bytes threshold
> > fd0: 1.44MB 3.5in
> > wdc0 not found at 0x1f0
> > wdc1 not found at 0x170
> > wt0 not found at 0x300
> > mcd0 not found at 0x300
> > matcdc0 not found at 0x230
> > scd0 not found at 0x230
> > ppc0 at 0x378 irq 7 on isa
> > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
> > ppc0: FIFO with 16/16/8 bytes threshold
> > nlpt0: <generic printer> on ppbus 0
> > nlpt0: Interrupt-driven port
> > ppi0: <generic parallel i/o> on ppbus 0
> > plip0: <PLIP network interface> on ppbus 0
> > ie0: unknown board_id: f000
> > ie0 not found at 0x300
> > ep0 not found at 0x300
> > ex0 not found
> > le0 not found at 0x300
> > lnc0 not found at 0x280
> > ze0 not found at 0x300
> > zp0 not found at 0x300
> > cs0 not found at 0x300
> > bt0 not found at 0x134
> > aha0 not found at 0x134
> > vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
> > npx0 on motherboard
> > npx0: INT 16 interface
> > ccd0-3: Concatenated disk drivers
> > Waiting 5 seconds for SCSI devices to settle
> > changing root device to da0s1a
> > da1 at ahc0 bus 0 target 1 lun 0
> > da1: <Quantum XP34300 L912> Fixed Direct Access SCSI-2 device
> > da1: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled
> > da1: 4101MB (8399520 512 byte sectors: 255H 63S/T 522C)
> > da5 at ahc1 bus 0 target 1 lun 0
> > da5: <Quantum XP34300 L912> Fixed Direct Access SCSI-2 device
> > da5: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled
> > da5: 4101MB (8399520 512 byte sectors: 255H 63S/T 522C)
> > da4 at ahc1 bus 0 target 0 lun 0
> > da4: <SEAGATE ST34555N 0930> Fixed Direct Access SCSI-2 device
> > da4: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled
> > da4: 4340MB (8888924 512 byte sectors: 255H 63S/T 553C)
> > da3 at ahc0 bus 0 target 3 lun 0
> > da3: <CONNER CFP2107S 2.14GB 172B> Fixed Direct Access SCSI-2 device
> > da3: 10.0MB/s transfers (10.0MHz, offset 15)
> > da3: 2048MB (4194304 512 byte sectors: 255H 63S/T 261C)
> > da0 at ahc0 bus 0 target 0 lun 0
> > da0: <MICROP 4110-09TBCU0322J HT01> Fixed Direct Access SCSI-2 device
> > da0: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled
> > da0: 1002MB (2053880 512 byte sectors: 64H 32S/T 1002C)
> > da2 at ahc0 bus 0 target 2 lun 0
> > da2: <SEAGATE ST34555N 0930> Fixed Direct Access SCSI-2 device
> > da2: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled
> > da2: 4340MB (8888924 512 byte sectors: 255H 63S/T 553C)
> > da6 at ahc1 bus 0 target 2 lun 0
> > da6: <SEAGATE ST32155N 0594> Fixed Direct Access SCSI-2 device
> > da6: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled
> > da6: 2049MB (4197405 512 byte sectors: 255H 63S/T 261C)
> > da7 at ahc1 bus 0 target 4 lun 0
> > da7: <IBM DDRS-39130 S97B> Fixed Direct Access SCSI-2 device
> > da7: 10.0MB/s transfers (10.0MHz, offset 15), Tagged Queueing Enabled
> > da7: 8715MB (17850000 512 byte sectors: 255H 63S/T 1111C)
When one looks more closely on this, the probe order seems a bit strange
to me, first 1 on controller 1 then 5 on controller 2, 4 on controller
2, 3 on controller 1, 0 on controller 1, 2 on controller 1, then 6 and 7
on controller 2. Can this be of importance?
--
__o
regards, Gunnar ---_ \<,_
email: flygt@sr.se ---- (_)/ (_)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19990501105950.A87391>