Date: Fri, 07 Aug 1998 01:45:17 -0400 From: Howard Leadmon <hdl@abs.net> To: freebsd-hardware@FreeBSD.ORG Cc: freebsd-questions@FreeBSD.ORG Subject: 3.0-19980720-SNAP & de driver full-duplex troubles?? Message-ID: <199808070545.BAA00539@dll.abs.net>
next in thread | raw e-mail | index | archive | help
I loaded up the 3.0 SNAP the other day and things seemed to be going
well, and then I decided to try and put the DEC-21140 based board I had
into full-duplex mode. Needless to say I also put the EtherSwitch it
was connected to into full-duplex mode (I know the switch handles this
well as I have a bunch of Solaris boxes running full-duplex on the same
switch).
My throughput came to a screeching halt, I could barely even FTP any
files across. Also even though the machine claimed it was in full-duplex
mode, it's still showing collisions even after a fresh reboot.
Here is what I get from ifconfig:
$ ifconfig -a
de0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 207.114.0.144 netmask 0xffffff00 broadcast 207.114.0.255
inet 207.114.0.241 netmask 0xffffff00 broadcast 207.114.0.255
inet 207.114.0.242 netmask 0xffffff00 broadcast 207.114.0.255
ether 00:c0:f0:30:0d:ad
media: 10baseT/UTP <full-duplex> (10baseT/UTP) status: active
supported media: autoselect 100baseTX <full-duplex> 100baseTX
10baseT/UTP <full-duplex> 10baseT/UTP
Also looking at dmesg from the reboot, it appears to be in full-duplex:
de0: <Digital 21140A Fast Ethernet> rev 0x22 int a irq 11 on pci0.20.0
de0: 21140A [10-100Mb/s] pass 2.2
de0: address 00:c0:f0:30:0d:ad
de0: enabling 10baseT port
de0: enabling Full Duplex 10baseT port
Now the way I did this, was to just set the following in my rc.conf
file on the machine:
ifconfig_de0="inet 207.114.0.144 netmask 255.255.255.0 media 10baseT/UTP
mediaopt full-duplex"
So with all the above set, still a netstat -i shows:
$ netstat -i
Name Mtu Network Address Ipkts Ierrs Opkts Oerrs Coll
de0 1500 <Link> 00.c0.f0.30.0d.ad 238593178 11 237898092 5096726
4662492
de0 1500 207.114 u2 238593178 11 237898092 5096726
4662492
So it is seeing collisions, and I can only assume it's runing in half-duplex
mode, even though everything seems to point to full-duplex.
So does anyone have any ideas? Is the full-duplex option broken in 3.0
current?
As this machine is being used for an IRC server, it's seeing a lot of small
packets, so running full-duplex would sure cut out a lot of collisions.
---
Howard Leadmon - hdl@abs.net - http://www.abs.net
ABSnet Internet Services - Phone: 410-361-8160 - FAX: 410-361-8162
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199808070545.BAA00539>