Date: Sun, 10 Feb 2008 11:49:20 -0500 From: Jason Morgan <jwm-freebsd-questions@sentinelchicken.net> To: freebsd-questions@freebsd.org Subject: Lockup on Boot due to ACPI (Freebsd 7.0-RC2 i386) Message-ID: <20080210164920.GA46810@sentinelchicken.net>
next in thread | raw e-mail | index | archive | help
I just upgraded a system from 6.3-RELEASE to 7.0-RC2 (both i386) only
to discover that the system won't boot with ACPI enabled. ACPI was
working fine in 6.3. The problems occur at boot-up -- the system
simply stops loading at approximately the same place during each
attempt (noted below in the dmesg). I have added
`hint.acpi.0.disabled=1' to loader.conf to get around the issue
automatically. I have tried building new kernels with various options
added/removed, rebuilt world with updated source, etc.
I have included my system information below. The dmesg output (a full
boot with ACPI disabled) is `verbose' and I have edited it to show
where the lockup happens. I am more than willing to help out with any
debugging if needed. I just need some direction.
Thanks,
~Jason
# uname -a
FreeBSD penelope.skepsi.net 7.0-RC2 FreeBSD 7.0-RC2 #1: Sat Feb 9 23:35:18 UTC
2008 root@penelope.skepsi.net:/usr/obj/usr/src/sys/PENELOPE i386
Snipped dmesg:
# dmesg
[snip]
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
(probe0:ata1:0:0:0): Down reving Protocol Version from 2 to 0?
(probe0:ata1:0:0:0): error 6
(probe0:ata1:0:0:0): Unretryable Error
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
# Failure occurs here when ACPI is enabled.
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
(probe1:sbp0:0:0:0): error 22
(probe1:sbp0:0:0:0): Unretryable Error
[snip]
Full dmesg:
# dmesg
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RC2 #1: Sat Feb 9 23:35:18 UTC 2008
root@penelope.skepsi.net:/usr/obj/usr/src/sys/PENELOPE
Preloaded elf kernel "/boot/kernel/kernel" at 0xc1084000.
Preloaded elf module "/boot/kernel/linux.ko" at 0xc1084174.
Preloaded elf module "/boot/kernel/pf.ko" at 0xc1084220.
Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc10842c8.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc1084374.
Preloaded elf module "/boot/modules/nvidia.ko" at 0xc1084420.
Preloaded elf module "/boot/kernel/aio.ko" at 0xc10844cc.
Calibrating clock(s) ... i8254 clock: 1193174 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1830015303 Hz
CPU: AMD Athlon(tm) XP 2500+ (1830.02-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x6a0 Stepping = 0
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM
OV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0400800<SYSCALL,MMX+,3DNow!+,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 internal cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory = 1073676288 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001428000 - 0x000000003eda7fff, 1033371648 bytes (252288 pages)
avail memory = 1032912896 (985 MB)
mptable_probe: MP Config Table has bad signature: F8/I
APIC: Could not find any APICs.
bios32: Found BIOS32 Service Directory header at 0xc00fb2b0
bios32: Entry = 0xfb740 (c00fb740) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb770
pnpbios: Found PnP BIOS data at 0xc00fc1c0
pnpbios: Entry = f0000:c1f0 Rev = 1.0
Other BIOS signatures found:
ULE: setup cpu group 0
ULE: setup cpu 0
ULE: adding cpu 0 to group 0: cpus 1 mask 0x1
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_buffersize=16
384 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
random: <entropy source, Software, Yarrow>
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
nfslock: pseudo-device
npx0: INT 16 interface
cpu0 on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000888
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=01e010de)
pcibios: BIOS version 2.10
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard
$PIR: Links after initial probe:
Link IRQ Rtd Ref IRQs
0x1 255 N 3 3 4 5 7 9 10 11 12 14 15
0x2 255 N 6 3 4 5 7 9 10 11 12 14 15
0x3 255 N 3 3 4 5 7 9 10 11 12 14 15
0x4 255 N 4 3 4 5 7 9 10 11 12 14 15
$PIR: Found matching pin for 1.6.INTA at func 0: 11
$PIR: Links after initial IRQ discovery:
Link IRQ Rtd Ref IRQs
0x1 255 N 3 3 4 5 7 9 10 11 12 14 15
0x2 255 N 6 3 4 5 7 9 10 11 12 14 15
0x3 11 Y 3 3 4 5 7 9 10 11 12 14 15
0x4 255 N 4 3 4 5 7 9 10 11 12 14 15
$PIR: IRQs used by BIOS: 11
$PIR: Interrupt Weights:
[ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
[ 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 ]
pci0: <PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x10de, dev=0x01e0, revid=0xa2
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Prefetchable Memory, range 32, base 0xe0000000, size 26, e
nabled
found-> vendor=0x10de, dev=0x01eb, revid=0xa2
domain=0, bus=0, slot=0, func=1
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ee, revid=0xa2
domain=0, bus=0, slot=0, func=2
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ed, revid=0xa2
domain=0, bus=0, slot=0, func=3
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ec, revid=0xa2
domain=0, bus=0, slot=0, func=4
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ef, revid=0xa2
domain=0, bus=0, slot=0, func=5
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x0060, revid=0xa3
domain=0, bus=0, slot=1, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x0064, revid=0xa2
domain=0, bus=0, slot=1, func=1
class=0c-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
map[10]: type I/O Port, range 32, base 0xe000, size 5, enabled
$PIR: No matching entry for 0.1.INTA
found-> vendor=0x10de, dev=0x0067, revid=0xa3
domain=0, bus=0, slot=2, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xe9086000, size 12, enabled
$PIR: No matching entry for 0.2.INTA
found-> vendor=0x10de, dev=0x0067, revid=0xa3
domain=0, bus=0, slot=2, func=1
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=b, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xe9082000, size 12, enabled
$PIR: No matching entry for 0.2.INTB
found-> vendor=0x10de, dev=0x0068, revid=0xa3
domain=0, bus=0, slot=2, func=2
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=c, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xe9085000, size 8, enabled
$PIR: No matching entry for 0.2.INTC
found-> vendor=0x10de, dev=0x006b, revid=0xa2
domain=0, bus=0, slot=5, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x01 (250 ns), maxlat=0x0c (3000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xe9000000, size 19, enabled
$PIR: No matching entry for 0.5.INTA
found-> vendor=0x10de, dev=0x006a, revid=0xa1
domain=0, bus=0, slot=6, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x05 (1250 ns)
intpin=a, irq=12
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0xd000, size 8, enabled
map[14]: type I/O Port, range 32, base 0xd400, size 7, enabled
map[18]: type Memory, range 32, base 0xe9080000, size 12, enabled
$PIR: No matching entry for 0.6.INTA
found-> vendor=0x10de, dev=0x006c, revid=0xa3
domain=0, bus=0, slot=8, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x02 (500 ns)
found-> vendor=0x10de, dev=0x0065, revid=0xa2
domain=0, bus=0, slot=9, func=0
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type I/O Port, range 32, base 0xf000, size 4, enabled
found-> vendor=0x10de, dev=0x006e, revid=0xa3
domain=0, bus=0, slot=13, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=3
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xe9083000, size 11, enabled
map[14]: type Memory, range 32, base 0xe9084000, size 6, enabled
$PIR: No matching entry for 0.13.INTA
found-> vendor=0x10de, dev=0x01e8, revid=0xa2
domain=0, bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
Correcting nForce2 C1 CPU disconnect hangs
agp0: <NVIDIA nForce2 AGP Controller> on hostb0
hostb0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe0000000
agp0: allocating GATT for aperture of size 64M
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xe9086000-0xe9086fff irq 12 at devic
e 2.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xe9086000
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xe9082000-0xe9082fff irq 10 at devic
e 2.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xe9082000
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
ehci0: <NVIDIA nForce2 USB 2.0 controller> mem 0xe9085000-0xe90850ff irq 11 at d
evice 2.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xe9085000
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <NVIDIA nForce2 USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 6 ports with 6 removable, self powered
ugen0: <Canon CanoScan, class 255/255, rev 2.00/3.06, addr 2> on uhub2
pci0: <multimedia, audio> at device 5.0 (no driver attached)
pcm0: <nVidia nForce2> port 0xd000-0xd0ff,0xd400-0xd47f mem 0xe9080000-0xe9080ff
f irq 12 at device 6.0 on pci0
pcm0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xd000
pcm0: Reserved 0x80 bytes for rid 0x14 type 4 at 0xd400
pcm0: [MPSAFE]
pcm0: [ITHREAD]
pcm0: <Avance Logic ALC650 AC97 Codec (id = 0x414c4720)>
pcm0: Codec features 20 bit DAC, 18 bit ADC, 5 bit master volume, Realtek 3D Ste
reo Enhancement
pcm0: Primary codec extended features variable rate PCM, double rate PCM, reserv
ed 1, center DAC, surround DAC, LFE DAC, reserved 4
pcm0: ac97 codec dac ready count: 0
pcm0: Mixer "vol":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "line":
pcm0: Mixer "mic":
pcm0: Mixer "cd":
pcm0: Mixer "rec":
pcm0: Mixer "igain":
pcm0: Mixer "ogain":
pcm0: Mixer "line1":
pcm0: Mixer "phin":
pcm0: Mixer "phout":
pcm0: Mixer "video":
pcm0: clone manager: deadline=750ms flags=0x8000001e
pcm0: sndbuf_setmap 2000000, 4000; 0xe4780000 -> 2000000
pcm0: sndbuf_setmap 2008000, 4000; 0xe4784000 -> 2008000
pcib1: <PCIBIOS PCI-PCI bridge> at device 8.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xcfff
pcib1: memory decode 0xe7000000-0xe8ffffff
pcib1: no prefetched decode
pci1: <PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x1186, dev=0x4b01, revid=0x11
domain=0, bus=1, slot=6, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xe8000000, size 14, enabled
pcib1: requested memory range 0xe8000000-0xe8003fff: good
map[14]: type I/O Port, range 32, base 0xc000, size 8, enabled
pcib1: requested I/O range 0xc000-0xc0ff: in range
$PIR: 1:6 INTA routed to irq 11
skc0: <D-Link DGE-530T Gigabit Ethernet> port 0xc000-0xc0ff mem 0xe8000000-0xe80
03fff irq 11 at device 6.0 on pci1
skc0: Reserved 0x4000 bytes for rid 0x10 type 3 at 0xe8000000
skc0: interrupt moderation is 100 us
skc0: DGE-530T Gigabit Ethernet Adapter rev. (0x9)
skc0: chip ver = 0xb1
skc0: chip rev = 0x09
skc0: SK_EPROM0 = 0x10
skc0: SRAM size = 0x010000
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: bpf attached
sk0: Ethernet address: 00:15:e9:fa:2c:36
miibus0: <MII bus> on sk0
e1000phy0: <Marvell 88E1011 Gigabit PHY> PHY 0 on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
skc0: [MPSAFE]
skc0: [ITHREAD]
atapci0: <nVidia nForce2 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,
0x376,0xf000-0xf00f at device 9.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
ata1: [ITHREAD]
fwohci0: vendor=10de, dev=6e
fwohci0: vendor=10de, dev=6e
fwohci0: <1394 Open Host Controller Interface> mem 0xe9083000-0xe90837ff,0xe9084
000-0xe908403f irq 3 at device 13.0 on pci0
fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xe9083000
fwohci0: [MPSAFE]
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:00:30:1b:ad:43:88
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x172c000
fwip0: <IP over FireWire> on firewire0
fwip0: bpf attached
fwip0: Firewire address: 00:00:00:30:1b:ad:43:88 @ 0xfffe00000000, S400, maxrec
2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
fwohci0: BUS reset
pcib2: <PCI-PCI bridge> at device 30.0 on pci0
pcib2: domain 0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xe4000000-0xe6ffffff
pcib2: prefetched decode 0xd0000000-0xdfffffff
pci2: <PCI bus> on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x10de, dev=0x02e0, revid=0xa2
domain=0, bus=2, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xe4000000, size 24, enabled
pcib2: requested memory range 0xe4000000-0xe4ffffff: good
map[14]: type Prefetchable Memory, range 32, base 0xd0000000, size 28, e
nabled
pcib2: requested memory range 0xd0000000-0xdfffffff: good
map[18]: type Memory, range 32, base 0xe5000000, size 24, enabled
pcib2: requested memory range 0xe5000000-0xe5ffffff: good
$PIR: Found IRQ 3 for link 0x4 from 3 5 10 11 12
$PIR: ROUTE_INTERRUPT failed.
nvidia0: <GeForce 7600 GT> mem 0xe4000000-0xe4ffffff,0xd0000000-0xdfffffff,0xe50
00000-0xe5ffffff irq 10 at device 0.0 on pci2
nvidia0: Reserved 0x1000000 bytes for rid 0x10 type 3 at 0xe4000000
nvidia0: Reserved 0x10000000 bytes for rid 0x14 type 3 at 0xd0000000
nvidia0: Reserved 0x1000000 bytes for rid 0x18 type 3 at 0xe5000000
nvidia0: [GIANT-LOCKED]
nvidia0: [ITHREAD]
pnpbios: 13 devices, largest 92 bytes
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0xffffff, size=0xf00000
pnpbios: handle 7 device ID PNP0c01 (010cd041)
PNP0c02: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c02: adding fixed memory32 range 0xcee00-0xcffff, size=0x1200
pnpbios: handle 8 device ID PNP0c02 (020cd041)
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
pnpbios: handle 9 device ID PNP0a03 (030ad041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 11 device ID PNP0501 (0105d041)
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0
PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0
PNP0700: adding irq mask 0x40
pnpbios: handle 12 device ID PNP0700 (0007d041)
PNP0400: adding irq mask 0x80
PNP0400: adding io range 0x378-0x37f, size=0x8, align=0
PNP0400: adding io range 0x778-0x77f, size=0x8, align=0
pnpbios: handle 13 device ID PNP0400 (0004d041)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0x41ab (2)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0067
psm0: strange result for test aux port (2).
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
ppbus0: [MPSAFE]
ppbus0: [ITHREAD]
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sio0: irq maps: 0x1001 0x1011 0x1001 0x1001
sio0: irq maps: 0x1001 0x1011 0x1001 0x1001
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1001 0x1001 0x1001 0x1001
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 pnpid PNP0303 on isa0
unknown: <PNP0800> failed to probe at port 0x61 pnpid PNP0800 on isa0
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0-0x9ffff pnpid PNP0c01 on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff pnpid PNP0501 on isa0
unknown: <PNP0700> failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 pnpid P
NP0700 on isa0
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0400> at port 0x378-0x37f pnpid PNP0400 on isa0
ums0: <Logitech USB RECEIVER, class 0/0, rev 1.10/25.10, addr 2> on uhub0
ums0: 16 buttons and Z dir.
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1830015303 Hz quality 800
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
atapicam: atapicam0 already exists; skipping it
ad0: setting PIO4 on nForce2 chip
ad0: setting UDMA100 on nForce2 chip
ad0: 76319MB <WDC WD800JB-00CRA1 17.07W17> at ata0-master UDMA100
ad0: 156301488 sectors [155061C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: nVidia check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire
acd0: setting PIO4 on nForce2 chip
acd0: setting UDMA66 on nForce2 chip
acd0: <PIONEER DVD-RW DVR-108/1.14> DVDR drive at ata1 as master
acd0: read 6890KB/s (6890KB/s) write 5511KB/s (5511KB/s), 2000KB buffer, UDMA66
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
pcm0: measured ac97 link rate at 47992 Hz, will use 48000 Hz
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
(probe0:ata1:0:0:0): Down reving Protocol Version from 2 to 0?
(probe0:ata1:0:0:0): error 6
(probe0:ata1:0:0:0): Unretryable Error
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x48 0x00 0x01
## failure occurs here when ACPI is enabled
(probe0:ata1:0:0:0): error 22
(probe0:ata1:0:0:0): Unretryable Error
(probe1:sbp0:0:0:0): error 22
(probe1:sbp0:0:0:0): Unretryable Error
(probe2:sbp0:0:1:0): error 22
(probe2:sbp0:0:1:0): Unretryable Error
(probe4:sbp0:0:3:0): error 22
(probe4:sbp0:0:3:0): Unretryable Error
(probe5:sbp0:0:4:0): error 22
(probe5:sbp0:0:4:0): Unretryable Error
(probe7:sbp0:0:6:0): error 22
(probe7:sbp0:0:6:0): Unretryable Error
(probe3:sbp0:0:2:0): error 22
(probe3:sbp0:0:2:0): Unretryable Error
(probe6:sbp0:0:5:0): error 22
(probe6:sbp0:0:5:0): Unretryable Error
GEOM: new disk cd0
pass0 at ata1 bus 0 target 0 lun 0
pass0: <PIONEER DVD-RW DVR-108 1.14> Removable CD-ROM SCSI-0 device
pass0: 66.000MB/s transfers
ATA PseudoRAID loaded
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
cd0 at ata1 bus 0 target 0 lun 0
cd0: <PIONEER DVD-RW DVR-108 1.14> Removable CD-ROM SCSI-0 device
cd0: 66.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
(cd0:ata1:0:0:0): error 6
(cd0:ata1:0:0:0): Unretryable Error
Trying to mount root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20080210164920.GA46810>