From owner-freebsd-bugs Thu Feb 23 07:05:26 1995 Return-Path: bugs-owner Received: (from majordom@localhost) by freefall.cdrom.com (8.6.9/8.6.6) id HAA03155 for bugs-outgoing; Thu, 23 Feb 1995 07:05:26 -0800 Received: from alpha.ineos.ac.ru (alpha.ineos.ac.ru [193.233.4.1]) by freefall.cdrom.com (8.6.9/8.6.6) with ESMTP id HAA03148 for ; Thu, 23 Feb 1995 07:05:10 -0800 Received: (from alex@localhost) by alpha.ineos.ac.ru (8.6.9/6) id SAA23650; Thu, 23 Feb 1995 18:03:07 +0300 Date: Thu, 23 Feb 1995 18:03:07 +0300 From: "Alexander V. Polyakov" Message-Id: <199502231503.SAA23650@alpha.ineos.ac.ru> To: Paul Richards In-Reply-To: Your Message of Mon, 20 Feb 1995 14:18:52 +0000 (GMT) Subject: Re: Another lnc0 bug? Cc: bugs@FreeBSD.org Reply-To: alex@ineos.ac.ru Organization: Institute of Organoelement Compounds, Russian Acad. Sci. X-Mailer: PC-Mail [PCM] X-Pcm-Version: 0.71 Sender: bugs-owner@FreeBSD.org Precedence: bulk On Mon, 20 Feb 1995, Paul Richards wrote: > In reply to Alexander V. Polyakov who said > > > > I'm using a PCnet-PCI (AMD 79C970) ethernet card and it also > > Hmm, I've had a report that these aren't even seen by the driver, obviously > they are. Yes, you are right. The driver lists my card as: lnc0 at 0xffe0-0xfff7 irq 9 drq 0 on eisa lnc0: PCnet-32 VL-Bus Ethernet controller, address 00:00:1a:40:38:02 The lance driver in Linux also sees the card as VL-Bus controller. I guess that this is caused by a bug in AMD 79C970 chip. > Is there a jumper that disables the SQE test? I've seen some cards with this. > The test should be enabled or you'll always see these errors. > > Otherwise you have a real hardware problem. > > Unless that is you have a twisted pair interface in which case the SQE test > gets disabled but the driver won't know that. The Am79C970 isn't specifically > supported at the moment and it has some extra features that the driver isn't > aware of. > Thank you very much for the advice. I have found the jumper "HB ENA/HB DIS" (not described in the NIC installation guide) whose factory setting was "HB DIS". After changing the setting to "HB ENA" my ethernet card works fine. The driver has stopped displaying error messages. By the way, the 'shutdown -r' command doesn't reboot the computer if I'm using PCI ethernet card. It writes: syncing disks... done Rebooting... Then it blanks the screen and dies until I press the reset button. If I exchange the PCI card for the ISA based NE2000 controller the 'shutdown -r' command works fine. This seems to be a hardware problem because the MS-DOS behaves similarly (doesn't reboot on Ctrl-Alt-Del). I'm using TMC PCI54PV motherboard (ISA/VESA/PCI) with a P54C/CT 90 MHz microprocessor and OPTI chipset (82C596/82C597/82C822). Any comments or advice would be greatly appreciated. Thanks in advance. Regards, Alex ---------------------------------------------------------------------------- Alexander V. Polyakov | Russian Academy of Sciences Systems Programmer / Analyst | Institute of Organoelement Compounds Phone: +7 095 1359331 | Fax: +7 095 1355085 | INEOS, 28 Vavilov str., 117813, E-mail: alex@ineos.ac.ru | Moscow, V-334, Russia ----------------------------------------------------------------------------