Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 29 May 2004 01:40:06 +0100
From:      Peter Wood <peter@alastria.net>
To:        freebsd-current@freebsd.org
Subject:   Interrupt issues on Tyan Tiger MPX m/b with FreeBSD 5.2-Current?
Message-ID:  <5tmfb09i8sfj84guendd86gqr74vigrao9@4ax.com>

next in thread | raw e-mail | index | archive | help
Hey folks,

I while back I posted a couple of reports of problems I was having with =
the
bge0 network card, which I eventually just put it down to bad chip sets.

However recently I've started to do a lot more with this server, and one =
of
these problems has occurred twice tonight while copying large amounts of =
data
over the network.

I have the following symptoms:

a) I can not use the last PCI slot (at the end of the board), any card I =
put
in there has issues with memory address' and other things.

b) The bge0 network card stops working with "watchdog timeout" errors =
very
quickly after use, twenty or thirty Mb will cause the symptoms to show.

c) The xl0 on the main board develops "watchdog timeout" errors at random
times under heavy load, this evening I've been copying raw wave files =
about.
It's relatively reproducible.

The mother board is a Tyan Tiger MPX, which I know is not the best, but I
believe it used to work satisfactorily using 4.5 (or around there), but =
it has
been a while so don't hold me to that.

ACPI doesn't seem to be an issue at least for points a and b, I haven't =
been
able to test c yet (working on a tight schedule with these raw waves :).

I'm assuming these are interrupt issues and routing of such, but I have =
no
knowledge of this field and was wondering if anyone could lend a hand to
discovering what is actually going on.

Any help would be appreciated, as always I can provide root access and
anything else needed. Attached is a verbose boot w/ ACPI.

Kind regards,

Peter.

ioapic0: intpin 2 polarity: high
lapic1: Routing NMI -> LINT1
lapic1: LINT1 trigger: edge
lapic1: LINT1 polarity: active-high
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: active-high
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0: intpin 9 polarity: low
ioapic0: intpin 9 trigger: level
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x01000000   VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD   RSDT> on motherboard
acpi0: [GIANT-LOCKED]
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80000818
pci_open(1a):	mode1res=3D0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=3D060000] [hdr=3D00] is there =
(id=3D700c1022)
pcibios: BIOS version 2.10
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 3
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
ACPI timer looks GOOD min =3D 4, max =3D 5, width =3D 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
ioapic0: Request to change trigger for pin 5 to level ignored
ioapic0: Request to change polarity for pin 5 to low ignored
ioapic0: Request to change trigger for pin 11 to level ignored
ioapic0: Request to change polarity for pin 11 to low ignored
ioapic0: Request to change trigger for pin 10 to level ignored
ioapic0: Request to change polarity for pin 10 to low ignored
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
cpu0: <ACPI CPU> port 0x530-0x537 on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
cpu1: <ACPI CPU> port 0x530-0x537 on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port =
0x8080-0x80ff,0x8000-0x807f,0xcf8-0xcff
iomem 0xd8000-0xdbfff on acpi0
ACPI PCI link initial configuration:
ACPI PCI link before setting link priority:
ACPI PCI link before fixup for boot-disabled links:
ACPI PCI link after fixup for boot-disabled links:
ACPI PCI link arbitrated configuration:
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=3D0
	map[10]: type 3, range 32, base f4000000, size 26, enabled
	map[14]: type 3, range 32, base f2100000, size 12, enabled
	map[18]: type 4, range 32, base 00001020, size  2, port disabled
found->	vendor=3D0x1022, dev=3D0x700c, revid=3D0x11
	bus=3D0, slot=3D0, func=3D0
	class=3D06-00-00, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0006, statreg=3D0x2230, cachelnsz=3D0 (dwords)
	lattimer=3D0x20 (960 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
found->	vendor=3D0x1022, dev=3D0x700d, revid=3D0x00
	bus=3D0, slot=3D1, func=3D0
	class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
	cmdreg=3D0x0007, statreg=3D0x0220, cachelnsz=3D0 (dwords)
	lattimer=3D0x63 (2970 ns), mingnt=3D0x0c (3000 ns), maxlat=3D0x00 (0 ns)
found->	vendor=3D0x1022, dev=3D0x7440, revid=3D0x05
	bus=3D0, slot=3D7, func=3D0
	class=3D06-01-00, hdrtype=3D0x00, mfdev=3D1
	cmdreg=3D0x000f, statreg=3D0x0220, cachelnsz=3D0 (dwords)
	lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
	map[20]: type 4, range 32, base 0000f000, size  4, enabled
found->	vendor=3D0x1022, dev=3D0x7441, revid=3D0x04
	bus=3D0, slot=3D7, func=3D1
	class=3D01-01-8a, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0005, statreg=3D0x0200, cachelnsz=3D0 (dwords)
	lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
found->	vendor=3D0x1022, dev=3D0x7443, revid=3D0x03
	bus=3D0, slot=3D7, func=3D3
	class=3D06-80-00, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0000, statreg=3D0x0280, cachelnsz=3D0 (dwords)
	lattimer=3D0x16 (660 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
	map[10]: type 4, range 32, base 00001038, size  3, enabled
	map[14]: type 4, range 32, base 00001030, size  2, enabled
	map[18]: type 4, range 32, base 00001028, size  3, enabled
	map[1c]: type 4, range 32, base 00001024, size  2, enabled
	map[20]: type 4, range 32, base 00001010, size  4, enabled
	map[24]: type 1, range 32, base f0000000, size 14, enabled
pcib0: matched entry for 0.8.INTA (src )
pcib0: device is hardwired to IRQ 20
found->	vendor=3D0x105a, dev=3D0x4d68, revid=3D0x02
	bus=3D0, slot=3D8, func=3D0
	class=3D01-80-85, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0007, statreg=3D0x0430, cachelnsz=3D16 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x04 (1000 ns), maxlat=3D0x12 (4500 =
ns)
	intpin=3Da, irq=3D20
	powerspec 1  supports D0 D1 D3  current D0
found->	vendor=3D0x1044, dev=3D0xa500, revid=3D0x02
	bus=3D0, slot=3D9, func=3D0
	class=3D06-04-00, hdrtype=3D0x01, mfdev=3D1
	cmdreg=3D0x0006, statreg=3D0x0290, cachelnsz=3D16 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x04 (1000 ns), maxlat=3D0x00 (0 ns)
	map[10]: type 3, range 32, base f8000000, size 26, enabled
pcib0: matched entry for 0.9.INTA (src )
pcib0: device is hardwired to IRQ 21
found->	vendor=3D0x1044, dev=3D0xa501, revid=3D0x02
	bus=3D0, slot=3D9, func=3D1
	class=3D0e-00-01, hdrtype=3D0x00, mfdev=3D1
	cmdreg=3D0x0016, statreg=3D0x0290, cachelnsz=3D16 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x01 (250 ns), maxlat=3D0x01 (250 =
ns)
	intpin=3Da, irq=3D21
	powerspec 2  supports D0 D3  current D0
found->	vendor=3D0x1022, dev=3D0x7448, revid=3D0x05
	bus=3D0, slot=3D16, func=3D0
	class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
	cmdreg=3D0x0017, statreg=3D0x2220, cachelnsz=3D0 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x04 (1000 ns), maxlat=3D0x00 (0 ns)
agp0: <AMD 762 host to AGP bridge> port 0x1020-0x1023 mem
0xf2100000-0xf2100fff,0xf4000000-0xf7ffffff at device 0.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf4000000
agp0: Reserved 0x1000 bytes for rid 0x14 type 3 at 0xf2100000
agp0: allocating GATT for aperture of size 64M
agp0: gatt -> ag_pdir 0x2a6000
agp0: allocating GATT for 16384 AGP page entries
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xf000-0xfff
pcib1:   memory decode     0xf1000000-0xf1ffffff
pcib1:   prefetched decode 0xfc000000-0xfcffffff
ACPI PCI link initial configuration:
ACPI PCI link before setting link priority:
ACPI PCI link before fixup for boot-disabled links:
ACPI PCI link after fixup for boot-disabled links:
ACPI PCI link arbitrated configuration:
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=3D1
	map[10]: type 1, range 32, base f1000000, size 24, enabled
pcib1: device (null) requested decoded memory range 0xf1000000-0xf1ffffff
	map[14]: type 3, range 32, base fc000000, size 24, enabled
pcib1: device (null) requested decoded memory range 0xfc000000-0xfcffffff
pcib1: matched entry for 1.5.INTA (src )
pcib1: device is hardwired to IRQ 18
found->	vendor=3D0x10de, dev=3D0x0020, revid=3D0x04
	bus=3D1, slot=3D5, func=3D0
	class=3D03-00-00, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0003, statreg=3D0x02b0, cachelnsz=3D0 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x05 (1250 ns), maxlat=3D0x01 (250 =
ns)
	intpin=3Da, irq=3D18
	powerspec 1  supports D0 D3  current D0
pci1: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 768 UDMA100 controller> port
0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=3D03 ostat0=3D50 ostat1=3D00
ata0-master: stat=3D0x80 err=3D0x80 lsb=3D0x80 msb=3D0x80
ata0-master: stat=3D0x80 err=3D0x80 lsb=3D0x80 msb=3D0x80
ata0-master: stat=3D0x80 err=3D0x80 lsb=3D0x80 msb=3D0x80
ata0-master: stat=3D0x80 err=3D0x80 lsb=3D0x80 msb=3D0x80
ata0-master: stat=3D0x00 err=3D0x01 lsb=3D0x14 msb=3D0xeb
ata0-slave:  stat=3D0x00 err=3D0x00 lsb=3D0x00 msb=3D0x00
ata0: reset tp2 mask=3D03 stat0=3D00 stat1=3D00 =
devices=3D0x4<ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=3D03 ostat0=3D10 ostat1=3D01
ata1-master: stat=3D0x10 err=3D0x01 lsb=3D0x14 msb=3D0xeb
ata1-slave:  stat=3D0x01 err=3D0x01 lsb=3D0x14 msb=3D0xeb
ata1: reset tp2 mask=3D03 stat0=3D10 stat1=3D01
devices=3D0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
atapci1: <Promise PDC20268 UDMA100 controller> port
0x1010-0x101f,0x1024-0x1027,0x1028-0x102f,0x1030-0x1033,0x1038-0x103f mem
0xf0000000-0xf0003fff irq 20 at device 8.0 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1010
atapci1: [MPSAFE]
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1038
atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x1030
ata2: reset tp1 mask=3D03 ostat0=3D50 ostat1=3D00
ata2-master: stat=3D0x50 err=3D0x01 lsb=3D0x00 msb=3D0x00
ata2-slave:  stat=3D0x00 err=3D0x01 lsb=3D0x00 msb=3D0x00
ata2: reset tp2 mask=3D03 stat0=3D50 stat1=3D00 devices=3D0x1<ATA_MASTER>
ata2: at 0x1038 on atapci1
ata2: [MPSAFE]
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x1028
atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x1024
ata3: reset tp1 mask=3D03 ostat0=3D50 ostat1=3D00
ata3-master: stat=3D0x50 err=3D0x01 lsb=3D0x00 msb=3D0x00
ata3-slave:  stat=3D0x00 err=3D0x01 lsb=3D0x00 msb=3D0x00
ata3: reset tp2 mask=3D03 stat0=3D50 stat1=3D00 devices=3D0x1<ATA_MASTER>
ata3: at 0x1028 on atapci1
ata3: [MPSAFE]
pcib2: <PCI-PCI bridge> at device 9.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0x0-0x0
pcib2:   memory decode     0x100000-0xfffff
pcib2:   prefetched decode 0x100000-0xfffff
pci2: <PCI bus> on pcib2
pci2: physical bus=3D2
asr0: <Adaptec Caching SCSI RAID> mem 0xf8000000-0xfbffffff irq 21 at =
device
9.1 on pci0
asr0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf8000000
asr0: [GIANT-LOCKED]
asr0: ADAPTEC 2400A FW Rev. 370L, 4 channel, 256 CCBs, Protocol I2O
pcib3: <ACPI PCI-PCI bridge> at device 16.0 on pci0
pcib3:   secondary bus     3
pcib3:   subordinate bus   3
pcib3:   I/O decode        0x2000-0x2fff
pcib3:   memory decode     0xf2000000-0xf20fffff
pcib3:   prefetched decode 0xfff00000-0xfffff
ACPI PCI link initial configuration:
ACPI PCI link before setting link priority:
ACPI PCI link before fixup for boot-disabled links:
ACPI PCI link after fixup for boot-disabled links:
ACPI PCI link arbitrated configuration:
pci3: <ACPI PCI bus> on pcib3
pci3: physical bus=3D3
	map[10]: type 1, range 32, base f2010000, size 12, enabled
pcib3: device (null) requested decoded memory range 0xf2010000-0xf2010fff
pcib3: matched entry for 3.0.INTD (src )
pcib3: device is hardwired to IRQ 19
found->	vendor=3D0x1022, dev=3D0x7449, revid=3D0x07
	bus=3D3, slot=3D0, func=3D0
	class=3D0c-03-10, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0017, statreg=3D0x0280, cachelnsz=3D0 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x50 (20000 =
ns)
	intpin=3Dd, irq=3D19
	map[10]: type 4, range 32, base 00002000, size  8, enabled
pcib3: device (null) requested decoded I/O range 0x2000-0x20ff
	map[14]: type 1, range 32, base f2011000, size 12, enabled
pcib3: device (null) requested decoded memory range 0xf2011000-0xf2011fff
pcib3: matched entry for 3.4.INTA (src )
pcib3: device is hardwired to IRQ 16
found->	vendor=3D0x9004, dev=3D0x5078, revid=3D0x03
	bus=3D3, slot=3D4, func=3D0
	class=3D01-00-00, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0017, statreg=3D0x0290, cachelnsz=3D16 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x04 (1000 ns), maxlat=3D0x04 (1000 =
ns)
	intpin=3Da, irq=3D16
	powerspec 1  supports D0 D3  current D0
	map[10]: type 4, range 32, base 00002480, size  6, enabled
pcib3: device (null) requested decoded I/O range 0x2480-0x24bf
pcib3: matched entry for 3.5.INTA (src )
pcib3: device is hardwired to IRQ 17
found->	vendor=3D0x1274, dev=3D0x5000, revid=3D0x00
	bus=3D3, slot=3D5, func=3D0
	class=3D04-01-00, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0005, statreg=3D0x0400, cachelnsz=3D0 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x0c (3000 ns), maxlat=3D0x80 (32000=
 ns)
	intpin=3Da, irq=3D17
	map[10]: type 1, range 64, base f2000000, size 16, enabled
pcib3: device (null) requested decoded memory range 0xf2000000-0xf200ffff
pcib3: matched entry for 3.6.INTA (src )
pcib3: device is hardwired to IRQ 18
found->	vendor=3D0x173b, dev=3D0x03ea, revid=3D0x15
	bus=3D3, slot=3D6, func=3D0
	class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0016, statreg=3D0x02b0, cachelnsz=3D16 (dwords)
	lattimer=3D0x40 (1920 ns), mingnt=3D0x40 (16000 ns), maxlat=3D0x00 (0 =
ns)
	intpin=3Da, irq=3D18
	powerspec 2  supports D0 D3  current D0
	MSI supports 8 messages, 64 bit
	map[10]: type 4, range 32, base 00002400, size  7, enabled
pcib3: device (null) requested decoded I/O range 0x2400-0x247f
	map[14]: type 1, range 32, base f2012000, size  7, enabled
pcib3: device (null) requested decoded memory range 0xf2012000-0xf201207f
pcib3: matched entry for 3.8.INTA (src )
pcib3: device is hardwired to IRQ 19
found->	vendor=3D0x10b7, dev=3D0x9200, revid=3D0x78
	bus=3D3, slot=3D8, func=3D0
	class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
	cmdreg=3D0x0017, statreg=3D0x0210, cachelnsz=3D16 (dwords)
	lattimer=3D0x50 (2400 ns), mingnt=3D0x0a (2500 ns), maxlat=3D0x0a (2500 =
ns)
	intpin=3Da, irq=3D19
	powerspec 2  supports D0 D1 D2 D3  current D0
ohci0: <OHCI (generic) USB controller> mem 0xf2010000-0xf2010fff irq 19 =
at
device 0.0 on pci3
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf2010000
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ubt0: Micro Star International product 0x6970, rev 1.10/5.25, addr 2
ubt0: Interface 0 endpoints: interrupt=3D0x81, bulk-in=3D0x82, =
bulk-out=3D0x2
ubt0: Interface 1 (alt.config 5) endpoints: isoc-in=3D0x83, =
isoc-out=3D0x3;
wMaxPacketSize=3D49; nframes=3D6, buffer size=3D294
ahc0: <Adaptec 2902/04/10/15/20C/30C SCSI adapter> port 0x2000-0x20ff mem
0xf2011000-0xf2011fff irq 16 at device 4.0 on pci3
ahc0: Defaulting to MEMIO off
ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x2000
ahc0: No SEEPROM available.
ahc0: Host Adapter Bios disabled.  Using default SCSI device parameters
ahc0: Downloading Sequencer Program... 457 instructions downloaded
ahc0: Features 0x10100, Bugs 0x35, Flags 0x8401f44
ahc0: [GIANT-LOCKED]
aic7850: Single Channel A, SCSI Id=3D7, 3/253 SCBs
pcm0: <AudioPCI ES1370> port 0x2480-0x24bf irq 17 at device 5.0 on pci3
pcm0: Reserved 0x40 bytes for rid 0x10 type 4 at 0x2480
pcm0: [GIANT-LOCKED]
pcm0: sndbuf_setmap 7d673000, 1000; 0xc743f000 -> 7d673000
pcm0: sndbuf_setmap 2f1000, 1000; 0xc743d000 -> 2f1000
bge0: <Altima AC9100 Gigabit Ethernet, ASIC rev. 0x105> mem
0xf2000000-0xf200ffff irq 18 at device 6.0 on pci3
bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xf2000000
miibus0: <MII bus> on bge0
brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: bpf attached
bge0: Ethernet address: 00:09:5b:1b:90:91
bge0: [GIANT-LOCKED]
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x2400-0x247f mem
0xf2012000-0xf201207f irq 19 at device 8.0 on pci3
xl0: Reserved 0x80 bytes for rid 0x14 type 3 at 0xf2012000
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus1: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: OUI 0x00105a, model 0x0000, rev. 0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:e0:81:21:83:70
xl0: [GIANT-LOCKED]
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0047
psm0: failed to reset the aux device.
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
sio0: irq maps: 0xe001 0xe011 0xe001 0xe001
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: irq maps: 0xe001 0xe009 0xe001 0xe001
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem
0xe0000-0xe3fff,0xca800-0xd07ff,0xc8800-0xca7ff,0xc8000-0xc87ff,0xc0000-0=
xc7fff
on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1666734961 Hz quality -100
Timecounters tick every 10.000 msec
lo0: bpf attached
ata0-master: pio=3D0x0c wdma=3D0x22 udma=3D0x44 cable=3D80pin
ata0-master: setting PIO4 on AMD 768 chip
ata0-master: setting UDMA66 on AMD 768 chip
acd0: <Pioneer DVD-ROM ATAPIModel DVD-117 0107/E1.07> DVDROM drive at =
ata0 as
master
acd0: read 6894KB/s (6894KB/s), 256KB buffer, UDMA66
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata1-slave: FAILURE - ATAPI_IDENTIFY no interrupt
ata1-slave: FAILURE - ATAPI_IDENTIFY status=3D1<ERROR> =
error=3D1<ILLEGAL_LENGTH>
LBA=3D0
ata1-slave: FAILURE - ATAPI_IDENTIFY no interrupt
ata1-slave: FAILURE - ATAPI_IDENTIFY status=3D1<ERROR> =
error=3D1<ILLEGAL_LENGTH>
LBA=3D0
ata1-master: pio=3D0x0c wdma=3D0x22 udma=3D0xffffffff cable=3D40pin
ata1-master: setting PIO4 on AMD 768 chip
ata1-master: setting WDMA2 on AMD 768 chip
ast0: <Seagate STT20000A/8A51> tape drive at ata1 as master
ast0: 1000KB/s, transfer limit 108 blks, 324KB buffer, WDMA2
ast0: Medium: none, readonly, qfa, ecc, 512b
ata2-master: pio=3D0x0c wdma=3D0x22 udma=3D0x45 cable=3D80pin
ata2-master: setting PIO4 on Promise PDC20268 chip
ata2-master: setting UDMA100 on Promise PDC20268 chip
ad4: <WDC WD1200JB-00DUA3/75.13B75> ATA-6 disk at ata2-master
ad4: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad4
ata3-master: pio=3D0x0c wdma=3D0x22 udma=3D0x45 cable=3D80pin
ata3-master: setting PIO4 on Promise PDC20268 chip
ata3-master: setting UDMA100 on Promise PDC20268 chip
ad6: <IC35L060AVER07-0/ER6OA46A> ATA-5 disk at ata3-master
ad6: 58644MB (120103200 sectors), 119150 C, 16 H, 63 S, 512 B
ad6: 16 secs/int, 1 depth queue, UDMA100
Waiting 5 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:234436482
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 32256 length 120031478784 end 120031511039
GEOM: new disk ad6
GEOM: Configure ad4s1a, start 0 length 536870912 end 536870911
GEOM: Configure ad4s1b, start 536870912 length 2147483648 end 2684354559
GEOM: Configure ad4s1c, start 0 length 120031478784 end 120031478783
GEOM: Configure ad4s1d, start 2684354560 length 536870912 end 3221225471
GEOM: Configure ad4s1e, start 3221225472 length 536870912 end 3758096383
GEOM: Configure ad4s1f, start 3758096384 length 116273382400 end =
120031478783
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/11/63 s:63 l:120101877
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad6s1, start 32256 length 61492161024 end 61492193279
GEOM: Configure ad6s1c, start 0 length 61492161024 end 61492161023
GEOM: Configure ad6s1d, start 0 length 61492161024 end 61492161023
ahc0: Selection Timeout on A:0. 0 SCBs aborted
ahc0: Selection Timeout on A:1. 0 SCBs aborted
ahc0: Selection Timeout on A:3. 0 SCBs aborted
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 0, offset 0
(ahc0:A:4:0): Target Initiated SDTR
(ahc0:A:4:0): Sending SDTR period 45, offset 0
ahc0: Selection Timeout on A:5. 0 SCBs aborted
ahc0: Selection Timeout on A:6. 0 SCBs aborted
(probe30:ahc0:0:2:0): error 22
(probe30:ahc0:0:2:0): Unretryable Error
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
ahc0: target 4 synchronous at 10.0MHz, offset =3D 0xf
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
ahc0: target 2 synchronous at 10.0MHz, offset =3D 0xf
(ahc0:A:4:0): Sending SDTR period 19, offset f
(ahc0:A:4:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
pass0 at asr0 bus 0 target 0 lun 0
pass0: <ADAPTEC RAID-5 370L> Fixed Direct Access SCSI-2 device=20
pass0: Serial Number +
pass0: Tagged Queueing Enabled
pass1 at ahc0 bus 0 target 2 lun 0
pass1: <YAMAHA CRW8824S 1.00> Removable CD-ROM SCSI-2 device=20
pass1: 10.000MB/s transfers (10.000MHz, offset 15)
pass2 at ahc0 bus 0 target 4 lun 0
pass2: <Quantum DLT4000 CPQ DRV D473> Removable Sequential Access SCSI-2
device=20
pass2: Serial Number CX922M1222
pass2: 10.000MB/s transfers (10.000MHz, offset 15)
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <Quantum DLT4000 CPQ DRV D473> Removable Sequential Access SCSI-2 =
device=20
sa0: Serial Number CX922M1222
sa0: 10.000MB/s transfers (10.000MHz, offset 15)
GEOM: new disk cd0
GEOM: new disk da0
da0 at asr0 bus 0 target 0 lun 0
da0: <ADAPTEC RAID-5 370L> Fixed Direct Access SCSI-2 device=20
da0: Serial Number +
da0: Tagged Queueing Enabled
da0: 343419MB (703322112 512 byte sectors: 255H 63S/T 43779C)
(ahc0:A:2:0): Sending SDTR period 19, offset f
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x00000000   VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff
ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 3 (IRQ 3) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 6 (IRQ 6) to cluster 0
ioapic0: routing intpin 7 (IRQ 7) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 13 (IRQ 13) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic0: routing intpin 16 (IRQ 16) to cluster 0
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
ioapic0: routing intpin 18 (IRQ 18) to cluster 0
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
ioapic0: routing intpin 20 (IRQ 20) to cluster 0
ioapic0: routing intpin 21 (IRQ 21) to cluster 0
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
cd0 at ahc0 bus 0 target 2 lun 0
cd0: <YAMAHA CRW8824S 1.00> Removable CD-ROM SCSI-2 device=20
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present -=
 tray
closed
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
(ahc0:A:2:0): Sending SDTR period 19, offset f
(ahc0:A:2:0): Received SDTR period 19, offset f
	Filtered to period 19, offset f
(cd0:ahc0:0:2:0): error 6
(cd0:ahc0:0:2:0): Unretryable Error
[0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:703309572
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure da0s1, start 32256 length 360094500864 end 360094533119
GEOM: Configure da0s1c, start 0 length 360094500864 end 360094500863
GEOM: Configure da0s1d, start 0 length 360094500864 end 360094500863
Mounting root from ufs:/dev/ad4s1a
start_init: trying /sbin/init
Linux ELF exec handler installed
linprocfs registered
bge0: gigabit link up
x: 2
x: 2
x: 2
x: 2
x: 2
x: 2

Kind regards,

Pete.
--=20
Peter Wood <peter@alastria.net> :: Tel +44 7974 799440



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?5tmfb09i8sfj84guendd86gqr74vigrao9>