Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 19 Apr 2004 19:36:10 +0200
From:      Joerg Wunsch <j@ida.interface-business.de>
To:        freebsd-sparc@freebsd.org
Subject:   Re: 5.2.1 mini-ISO fails to boot on U450
Message-ID:  <20040419193610.A40602@ida.interface-business.de>
In-Reply-To: <20040415101408.GB41902@beastie.b0rken.org>; from jason-freebsdlists@freebsd.org on Thu, Apr 15, 2004 at 11:14:08AM %2B0100
References:  <20040415120849.B4638@ida.interface-business.de> <20040415101408.GB41902@beastie.b0rken.org>

next in thread | previous in thread | raw e-mail | index | archive | help
[Sorry for the silence, but I haven't been subscribed to sparc64 until
right now, so I didn't notice that reply.]

As Jason Mann wrote:

> > Fatal SCSI error  at script address 8 Illegal instruction
> > Drive not ready
> 
> Sounds like you have a dead disk.

Hmm, I doubt that.  The machine has been running Solaris until it got
retired.  The only change since is that a few out of its dozen of
drives have been removed.

> Open the door on the front of the server and check the status LEDs
> next to each disk.

They were all lit as expected.

Just out of curiosity, I've pulled all but one drive, but the same.

I found a FreeBSD 5.1 boot CD-ROM, and it gets me a few more messages
on the serial console but will eventually fail similarly:

Boot device: /pci@1f,4000/scsi@2/disk@6,0:f  File and args: 
 
>> FreeBSD/sparc64 boot block
   Boot path:   /pci@1f,4000/scsi@2/disk@6,0:f
   Boot loader: /boot/loader
Console: OpenFirmware console
Boot path set to /pci@1f,4000/scsi@2/disk@6,0:a

FreeBSD/sparc64 bootstrap loader, Revision 1.0
(fenner@sparkle.attlabs.net, Tue May  6 15:11:35 PDT 2003)
bootpath="/pci@1f,4000/scsi@2/disk@6,0:a"

[here the `twiddle' is spinning]

Loading /boot/defaults/loader.conf 
Fatal SCSI error  at script address 8 Illegal instruction
Drive not ready

How's the sparc64 CD-ROM organized, would it be possible to dd the
entire image onto a hard disk (using a Solaris boot), and try booting
off that hard drive, just to avoid the CD-ROM as the possible source
of error?

The drives itself are 4 GB Seagate Barracudas.  The SCSI controllers
are the standard Sym 53C876 (I believe) dual-channel controllers that
used to be in the E450.

Are there any requirements wrt. the OBP version?  It probably hasn't
been upgraded for a while... (it announces itself as 3.14).

Here's the output of probe-scsi-all (with a single hard drive) for
reference.

{0} ok probe-scsi-all
/pci@6,4000/scsi@4,1

/pci@6,4000/scsi@4

/pci@1f,4000/scsi@2
Target 5 
  Unit 0   Removable Tape     EXABYTE EXB-8505SMBANSH20090
Target 6 
  Unit 0   Removable Read Only device    TOSHIBA XM5701TASUN12XCD0997

/pci@1f,4000/scsi@3
Target 0 
  Unit 0   Disk     SEAGATE ST34371W SUN4.2G7462


Just to make sure I've also dug up an old 8 mm tape medium and loaded
it into the Exb drive, but still the same. :(

-- 
J"org Wunsch					       Unix support engineer
joerg_wunsch@interface-systems.de        http://www.interface-systems.de/~j/



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20040419193610.A40602>