Date: Sat, 27 Feb 2010 16:53:44 -0500 From: Alexander Bakst <alexander.bakst@gmail.com> To: Andreas Tobler <andreast-list@fgznet.ch> Cc: freebsd-ppc@freebsd.org Subject: Re: Fan/Power controls Message-ID: <4B899468.6050406@gmail.com> In-Reply-To: <4B89930D.3060800@fgznet.ch> References: <4B8984BF.5080607@oracle.com> <4B898D00.9030706@fgznet.ch> <4B898E84.1040200@gmail.com> <4B89930D.3060800@fgznet.ch>
next in thread | previous in thread | raw e-mail | index | archive | help
Well, I would boot into OS X, but I nuked everything on the HD :). So it doesn't exist. This is one of the dual 2.0 GHz G5 machines. --Alexander On 2/27/10 4:47 PM, Andreas Tobler wrote: > On 27.02.10 22:28, Alexander Bakst wrote: >> (Switched my non-work e-mail) >> >> Well, I actually am using a fancy apple G5 - I belive it is a power >> 970fx, not sure though. I'm not even sure how to check the current clock >> frequency of my cpu. To be honest, it would be fantastic if it weren't >> running at the highest speed, since I would like to save power. I don't >> know if the kernel will tell the cpu to snooze/nap. > > Hm, it is a 970FX @ 2000.36 MHz. > I'm confused that there is no smu? > Maybe this one lacks the smu. According to the docs I have, the 7,3 > behaves similar to the 7,2. And the 7,2/3 do not have an smu. The cpu > speed is controlled via freq and volt. And some nasty gpio interrupts > @ Nathan :) This bites me currently! > > Can you boot this machine into OS-X and see what it tells you about > the CPU speed? > > Hopefully I'm wrong :) > > Andreas > >> dmesg output: >> >> Copyright (c) 1992-2010 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 9.0-CURRENT #314 r204309:204312M: Thu Feb 25 09:28:38 CST 2010 >> >> root@comporellon.tachypleus.net:/usr/obj/powerpc/usr/src/sys/GENERIC >> powerpc >> cpu0: IBM PowerPC 970FX revision 3.0, 2000.36 MHz >> cpu0: Features dc000000<PPC32,PPC64,ALTIVEC,FPU,MMU> >> cpu0: HID0 511081<NAP,DPM,NHR,TBEN,ENATTN> >> real memory = 1060220928 (1011 MB) >> avail memory = 986472448 (940 MB) >> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs >> cpu0: dev=ff899e08 (BSP) >> cpu1: dev=ff89b2e8 >> ispfw: registered firmware<isp_1040> >> ispfw: registered firmware<isp_1040_it> >> ispfw: registered firmware<isp_1080> >> ispfw: registered firmware<isp_1080_it> >> ispfw: registered firmware<isp_12160> >> ispfw: registered firmware<isp_12160_it> >> ispfw: registered firmware<isp_2100> >> ispfw: registered firmware<isp_2200> >> ispfw: registered firmware<isp_2300> >> ispfw: registered firmware<isp_2322> >> ispfw: registered firmware<isp_2400> >> ispfw: registered firmware<isp_2400_multi> >> ispfw: registered firmware<isp_2500> >> ispfw: registered firmware<isp_2500_multi> >> kbd0 at kbdmux0 >> nexus0:<Open Firmware Nexus device> >> cpulist0:<Open Firmware CPU Group> on nexus0 >> cpu0:<Open Firmware CPU> on cpulist0 >> pcr0:<PPC 970 Power Control Register> on cpu0 >> pcr0: No power mode data in device tree! >> device_attach: pcr0 attach returned 6 >> cpu1:<Open Firmware CPU> on cpulist0 >> pcr1:<PPC 970 Power Control Register> on cpu1 >> pcr1: No power mode data in device tree! >> device_attach: pcr1 attach returned 6 >> pcib0:<Apple U3 Host-AGP bridge> on nexus0 >> pci0:<OFW PCI bus> on pcib0 >> vgapci0:<VGA-compatible display> port 0x400-0x4ff mem >> 0xa0000000-0xafffffff,0x90000000-0x9000ffff irq 48 at device 16.0 on >> pci0 >> cpcht0:<IBM CPC925 HyperTransport Tunnel> on nexus0 >> pcib1:<HyperTransport-PCI bridge> on cpcht0 >> pci1:<OFW PCI bus> on pcib1 >> macio0:<K2 KeyLargo I/O Controller> mem 0x80000000-0x8007ffff at device >> 7.0 on pci1 >> openpic0:<OpenPIC Interrupt Controller> mem 0x40000-0x7ffff on macio0 >> macgpio0:<MacIO GPIO Controller> mem 0x50-0x8a on macio0 >> scc0:<Zilog Z8530 dual channel SCC> mem >> 0x13000-0x13fff,0x8400-0x84ff,0x8500-0x85ff,0x8600-0x86ff,0x8700-0x87ff >> irq 22,5,6,23,7,8 on macio0 >> scc0: [FILTER] >> scc0: [FILTER] >> uart0:<z8530, channel A> on scc0 >> uart0: [FILTER] >> uart1:<z8530, channel B> on scc0 >> uart1: [FILTER] >> iichb0:<Keywest I2C controller> mem 0x18000-0x18fff irq 26 on macio0 >> iichb0: [ITHREAD] >> iicbus0:<OFW I2C bus> on iichb0 >> iicbus0:<unknown card> at addr 0x1c0 >> iicbus0:<unknown card> at addr 0x6a >> pmu0:<Apple PMU99 Controller> mem 0x16000-0x17fff irq 25 on macio0 >> ohci0:<OHCI (generic) USB controller> mem 0x80081000-0x80081fff irq 27 >> at device 8.0 on pci1 >> ohci0: [ITHREAD] >> usbus0:<OHCI (generic) USB controller> on ohci0 >> ohci1:<OHCI (generic) USB controller> mem 0x80080000-0x80080fff irq 28 >> at device 9.0 on pci1 >> ohci1: [ITHREAD] >> usbus1:<OHCI (generic) USB controller> on ohci1 >> pcib2:<HyperTransport-PCI bridge> on cpcht0 >> pci2:<OFW PCI bus> on pcib2 >> ohci2:<NEC uPD 9210 USB controller> mem 0x80702000-0x80702fff irq 63 at >> device 11.0 on pci2 >> ohci2: [ITHREAD] >> usbus2:<NEC uPD 9210 USB controller> on ohci2 >> ohci3:<NEC uPD 9210 USB controller> mem 0x80701000-0x80701fff irq 63 at >> device 11.1 on pci2 >> ohci3: [ITHREAD] >> usbus3:<NEC uPD 9210 USB controller> on ohci3 >> ehci0:<NEC uPD 720100 USB 2.0 controller> mem 0x80700000-0x807000ff irq >> 63 at device 11.2 on pci2 >> ehci0: [ITHREAD] >> usbus4: EHCI version 1.0 >> usbus4:<NEC uPD 720100 USB 2.0 controller> on ehci0 >> pcib3:<HyperTransport-PCI bridge> on cpcht0 >> pci3:<OFW PCI bus> on pcib3 >> ata0:<K2 Kauai ATA Controller> mem 0x80104000-0x80107fff irq 39 at >> device 13.0 on pci3 >> ata0: [ITHREAD] >> fwohci0:<1394 Open Host Controller Interface> mem 0x80100000-0x80100fff >> irq 40 at device 14.0 on pci3 >> fwohci0: [ITHREAD] >> fwohci0: OHCI version 1.0 (ROM=0) >> fwohci0: No. of Isochronous channels is 8. >> fwohci0: EUI64 00:0d:93:ff:fe:62:62:7c >> fwohci0: invalid speed 7 (fixed to 3). >> fwohci0: Phy 1394a available S800, 3 ports. >> fwohci0: Link S800, max_rec 4096 bytes. >> firewire0:<IEEE1394(FireWire) bus> on fwohci0 >> fwe0:<Ethernet over FireWire> on firewire0 >> if_fwe0: Fake Ethernet address: 02:0d:93:62:62:7c >> fwe0: Ethernet address: 02:0d:93:62:62:7c >> sbp0:<SBP-2/SCSI over FireWire> on firewire0 >> fwohci0: Initiate bus reset >> fwohci0: fwohci_intr_core: BUS reset >> fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=2, >> CYCLEMASTER mode >> pcib4:<HyperTransport-PCI bridge> on cpcht0 >> pci4:<OFW PCI bus> on pcib4 >> gem0:<Apple K2 GMAC Ethernet> mem 0x80400000-0x805fffff irq 41 at >> device 15.0 on pci4 >> miibus0:<MII bus> on gem0 >> brgphy0:<BCM54K2 10/100/1000baseTX PHY> PHY 1 on miibus0 >> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, >> 1000baseT-FDX, auto >> gem0: 10kB RX FIFO, 4kB TX FIFO >> gem0: Ethernet address: 00:0d:93:62:62:7c >> gem0: [ITHREAD] >> pcib5:<HyperTransport-PCI bridge> on cpcht0 >> pci5:<OFW PCI bus> on pcib5 >> atapci0:<ServerWorks K2 SATA150 controller> mem 0x80600000-0x80601fff >> irq 0 at device 12.0 on pci5 >> atapci0: [ITHREAD] >> ata2:<ATA channel 0> on atapci0 >> ata2: [ITHREAD] >> ata3:<ATA channel 1> on atapci0 >> ata3: [ITHREAD] >> ata4:<ATA channel 2> on atapci0 >> ata4: [ITHREAD] >> ata5:<ATA channel 3> on atapci0 >> ata5: [ITHREAD] >> atapci1:<ServerWorks K2 SATA150 controller> at device 12.1 on pci5 >> atapci1: unable to map interrupt >> device_attach: atapci1 attach returned 6 >> sc0:<System console> on nexus0 >> sc0: Unknown<16 virtual consoles, flags=0x300> >> Timecounter "decrementer" frequency 33333333 Hz quality 0 >> Timecounters tick every 10.000 msec >> firewire0: 1 nodes, maxhop<= 0 cable IRM irm(0) (me) >> firewire0: bus manager 0 >> usbus0: 12Mbps Full Speed USB v1.0 >> usbus1: 12Mbps Full Speed USB v1.0 >> ugen0.1:<Apple> at usbus0 >> uhub0:<Apple OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 >> ugen1.1:<Apple> at usbus1 >> uhub1:<Apple OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 >> usbus2: 12Mbps Full Speed USB v1.0 >> usbus3: 12Mbps Full Speed USB v1.0 >> ugen2.1:<NEC> at usbus2 >> uhub2:<NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 >> ugen3.1:<NEC> at usbus3 >> uhub3:<NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 >> usbus4: 480Mbps High Speed USB v2.0 >> ugen4.1:<NEC> at usbus4 >> uhub4:<NEC EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4 >> uhub0: 2 ports with 2 removable, self powered >> acd0: DVDR<PIONEER DVD-RW DVR-109/A912> at ata0-master UDMA66 >> uhub1: 2 ports with 2 removable, self powered >> ad0: 152627MB<WDC WD1600JD-41HBC0 21.02J21> at ata2-master UDMA100 SATA >> 1.5Gb/s >> uhub2: 3 ports with 3 removable, self powered >> uhub3: 2 ports with 2 removable, self powered >> uhub4: 5 ports with 5 removable, self powered >> ugen4.2:<vendor 0x0204> at usbus4 >> umass0:<vendor 0x0204 2090E, class 0/0, rev 2.00/1.00, addr 2> on >> usbus4 >> umass0: SCSI over Bulk-Only; quirks = 0x0000 >> SMP: AP CPU #1 launched >> Root mount waiting for: usbus4 >> umass0:1:0:-1: Attached to scbus1d >> a0 at umass-sim0 bus 0 scbus1 target 0 lun 0 >> da0:< 2090E 5.00> Removable Direct Access SCSI-2 device >> da0: 40.000MB/s transfers >> da0: 249MB (509952 512 byte sectors: 64H 32S/T 249C) >> (da0:umass-sim0:0:0:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 >> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not >> present) >> (da0:umass-sim0:0:0:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 >> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not >> present) >> (da0:umass-sim0:0:0:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 >> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not >> present) >> (da0:umass-sim0:0:0:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 >> (da0:umass-sim0:0:0:0): SCSI sense: NOT READY asc:3a,0 (Medium not >> present) >> Trying to mount root from ufs:/dev/ad0s3 >> GEOM_PART: Partition 'ad0s4' not suitable for kernel dumps (wrong type?) >> >> ugen2.2:<vendor 0x0409> at usbus2 >> uhub5:<vendor 0x0409 product 0x55ab, class 9/0, rev 1.00/1.00, addr 2> >> on usbus2 >> uhub5: 4 ports with 4 removable, bus powered >> ugen2.3:<Alps Electric> at usbus2 >> ukbd0:<Alps Electric M2452, class 0/0, rev 1.00/1.01, addr 3> on usbus2 >> kbd1 at ukbd0 >> ugen2.4:<Logitech> at usbus2 >> ums0:<Logitech M4848, class 0/0, rev 1.00/5.00, addr 4> on usbus2 >> ums0: 1 buttons and [XY] coordinates ID=0 >> gem0: link state changed to DOWN >> gem0: link state changed to UP >> gem0: link state changed to DOWN >> gem0: link state changed to UP > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?4B899468.6050406>