Date: Sun, 11 Nov 2007 13:11:42 -0600 From: Stephen Montgomery-Smith <stephen@math.missouri.edu> To: freebsd-stable <freebsd-stable@freebsd.org> Subject: FBSD-7-B2 Freeze Message-ID: <473753EE.7080505@math.missouri.edu>
next in thread | raw e-mail | index | archive | help
I am experiencing fairly consistent system freezes which seem to
coincide with using the ndis driver and nvidia driver at the same time.
I had worst problems using the nvidia binary driver, but I did also
experience a freeze one time with the xorg nv driver, which I am now
using. Sometimes the wireless card works extremely slowly when I am
using the nvidia driver.
I have a Dell Latitude D800. I enclose dmesg. Any advice on how to
either further diagnose, or fix the problem will be welcome.
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-BETA2 #0: Sat Nov 10 12:48:18 CST 2007
stephen@hub2.gateway.2wire.net:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) M processor 1.70GHz (1698.56-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6d6 Stepping = 6
Features=0xafe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE>
Features2=0x180<EST,TM2>
real memory = 536535040 (511 MB)
avail memory = 511066112 (487 MB)
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <DELL CPi R > on motherboard
acpi0: [ITHREAD]
acpi0: reservation of 0, 9fc00 (3) failed
acpi0: reservation of 100000, 1fef0000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci_link1: BIOS IRQ 11 for 0.31.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> mem
0xfc000000-0xfcffffff,0xd0000000-0xdfffffff irq 11 at device 0.0 on pci1
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f
irq 11 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f
irq 11 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f
irq 11 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem
0xf4fffc00-0xf4ffffff irq 11 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci_link1: BIOS IRQ 11 for 2.3.INTA is invalid
pci2: <ACPI PCI bus> on pcib2
pci0:2:0:0: bad VPD cksum, remain 14
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x3001>
mem 0xfaff0000-0xfaffffff irq 11 at device 0.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5705 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bge0: Ethernet address: 00:0f:1f:21:d5:92
bge0: [ITHREAD]
cbb0: <TI7510 PCI-CardBus Bridge> at device 1.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
cbb1: <TI7610 PCI-CardBus Bridge> irq 11 at device 1.1 on pci2
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [ITHREAD]
fwohci0: <1394 Open Host Controller Interface> mem
0xfafef800-0xfafeffff,0xfafe8000-0xfafebfff irq 11 at device 1.2 on pci2
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 48:4f:c0:00:36:a9:44:a1
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 4a:4f:c0:a9:44:a1
fwe0: Ethernet address: 4a:4f:c0:a9:44:a1
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 48:4f:c0:00:36:a9:44:a1 @ 0xfffe00000000, S400,
maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x13b0000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
pci2: <base peripheral> at device 1.3 (no driver attached)
ndis0: <Dell TrueMobile 1300 WLAN Mini-PCI Card> mem
0xfafec000-0xfafedfff irq 9 at device 3.0 on pci2
ndis0: [ITHREAD]
ndis0: NDIS API version: 5.1
ndis0: using obsoleted if_watchdog interface
ndis0: Ethernet address: 00:90:96:f6:2d:0e
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xbfa0-0xbfaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pcm0: <Intel ICH4 (82801DB)> port 0xb800-0xb8ff,0xbc40-0xbc7f mem
0xf4fff800-0xf4fff9ff,0xf4fff400-0xf4fff4ff irq 9 at device 31.5 on pci0
pcm0: [ITHREAD]
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model GlidePoint, device ID 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio0: [FILTER]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcf7ff,0xcf800-0xcffff pnpid
ORM0000 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1698564643 Hz quality 800
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 28615MB <IC25N030ATMR04 0 MOAOAD0A> at ata0-master UDMA100
acd0: CDRW <QSI CD-RW/DVD-ROM SBW242U/UD25> at ata1-master UDMA33
cbb1: power timeout, doom?
cbb1: Power not on?
pccard1: <unknown card> (manufacturer=0x0097, product=0x1620,
function_type=-1) at function 0
pccard1: CIS info: TEXAS Instruments, UltraMedia Smart Card Adapter, 1.0
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00
cd0 at ata1 bus 0 target 0 lun 0
cd0: <QSI CDRW/DVD SBW242U UD25> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad0s2a
Setting ESSID to ""
Setting ESSID to ""
Setting ESSID to "stephen"
Setting ESSID to "stephen"
Setting ESSID to "stephen"
Setting ESSID to "stephen"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?473753EE.7080505>