Date: Fri, 11 May 2007 13:14:02 +0700 (ICT) From: Olivier Nicole <on@cs.ait.ac.th> To: freebsd-questions@freebsd.org Subject: USB on 4.11 Message-ID: <200705110614.l4B6E2QU052996@banyan.cs.ait.ac.th>
next in thread | raw e-mail | index | archive | help
Hi, I am trying to enable USB on FreeBSD 4.11. If I boot the GENERIC kernel, my USB drive is recognized. If I boot my customized kernel, the drive is not present. in the customized kernel I have: # SCSI peripherals device scbus # SCSI bus (required) device da # Direct Access (disks) device sa # Sequential Access (tape etc) device pass # Passthrough device (direct SCSI access) # USB support device uhci # UHCI PCI->USB interface device ohci # OHCI PCI->USB interface device usb # USB Bus (required) device umass # Disks/Mass storage - Requires scbus and da which seems to be enough. usbd is enabled in rc.conf. When I boot GENERIC and plug in the USB disk: amanda<root>47: usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), (0x1166)(0x0000), rev 1.00 port 1 powered port 2 addr 2: full speed, self powered, config 1, USB TO IDE(0x0702), Genesys Logic(0x05e3), rev 0.02 port 3 powered port 4 powered amanda<root>48: camcontrol devlist -v scbus0 on sym0 bus 0: <SEAGATE ST318436LW 0010> at scbus0 target 0 lun 0 (pass0,da0) <SEAGATE ST318436LW 0010> at scbus0 target 1 lun 0 (pass1,da1) <SEAGATE ST318436LW 0010> at scbus0 target 2 lun 0 (pass2,da2) <SEAGATE ST318436LW 0010> at scbus0 target 3 lun 0 (pass3,da3) < > at scbus0 target -1 lun -1 () scbus1 on sym1 bus 0: <TANDBERG SLR100 0402> at scbus1 target 2 lun 0 (pass4,sa0) < > at scbus1 target -1 lun -1 () scbus2 on umass-sim0 bus 0: <ST380011 A 0811> at scbus2 target 0 lun 0 (da4,pass5) scbus-1 on xpt0 bus 0: < > at scbus-1 target -1 lun -1 (xpt0) This is the boot with GENERIC (note it is 4.10) Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.10-RELEASE #0: Tue May 25 22:47:12 GMT 2004 root@perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Intel Pentium III (800.03-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x686 Stepping = 6 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 402632704 (393196K bytes) avail memory = 386019328 (376972K bytes) Preloaded elf kernel "kernel.GENERIC" at 0xc0551000. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 11 entries at 0xc00f1010 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd800-0xd83f mem 0xfd800000-0xfd8fffff,0xfe000000-0xfe000fff irq 10 at device 2.0 on pci0 fxp0: Ethernet address 00:e0:18:0a:97:a6 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port 0xd400-0xd43f mem 0xfc800000-0xfc81ffff,0xfd000000-0xfd01ffff irq 11 at device 5.0 on pci0 em0: Speed:N/A Duplex:N/A pci0: <ATI Mach64-GR graphics accelerator> at 7.0 isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <ServerWorks ROSB4 ATA33 controller> port 0xb800-0xb80f at device 15.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 ohci0: <OHCI (generic) USB controller> mem 0xfa000000-0xfa000fff irq 7 at device 15.2 on pci0 usb0: OHCI version 1.0, legacy support usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered uhub0: device problem, disabling port 2 pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard pci1: <PCI bus> on pcib1 sym0: <896> port 0xb400-0xb4ff mem 0xf9000000-0xf9001fff,0xf9800000-0xf98003ff irq 4 at device 5.0 on pci1 sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym1: <896> port 0xb000-0xb0ff mem 0xf8000000-0xf8001fff,0xf8800000-0xf88003ff irq 3 at device 5.1 on pci1 sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. orm0: <Option ROMs> at iomem 0xc0000-0xca7ff,0xd0000-0xd17ff,0xd4000-0xd7fff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: failed to get data. psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: parallel port not found. acd0: CDROM <QSI CD-ROM SCR-242> at ata0-master PIO4 Waiting 15 seconds for SCSI devices to settle (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered. sa0 at sym1 bus 0 target 2 lun 0 sa0: <TANDBERG SLR100 0402> Removable Sequential Access SCSI-2 device sa0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit) da0 at sym0 bus 0 target 0 lun 0 da0: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da0: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) da3 at sym0 bus 0 target 3 lun 0 da3: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da3: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da3: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) da2 at sym0 bus 0 target 2 lun 0 da2: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da2: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) da1 at sym0 bus 0 target 1 lun 0 da1: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da1: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) em0: Link is up 1000 Mbps Full Duplex ** The USB is not properly detectec if plugged in while booting uhub0: device problem, disabling port 2 ** Unplug and replug USB disk and everything is fine. umass0: Genesys Logic USB TO IDE, rev 2.00/0.02, addr 2 da4 at umass-sim0 bus 0 target 0 lun 0 da4: <ST380011 A 0811> Fixed Direct Access SCSI-0 device da4: 650KB/s transfers da4: 76319MB (156301488 512 byte sectors: 64H 32S/T 10783C) This is the boot with trimed down kernel (note this is 4.11-p21) ACPI debug layer 0x0 debug level 0x0 Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.11-RELEASE-p21 #3: Thu May 10 15:55:28 ICT 2007 root@amanda.cs.ait.ac.th:/usr/src/sys/compile/SMALL Timecounter "i8254" frequency 1193182 Hz CPU: Intel Pentium III (800.03-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x686 Stepping = 6 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 402632704 (393196K bytes) avail memory = 387461120 (378380K bytes) Changing APIC ID for IO APIC #1 from 3 to 1 in MP table Changing APIC ID for IO APIC #1 from 3 to 1 on chip Programming 16 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 Programming 16 pins in IOAPIC #1 FreeBSD/SMP: Multiprocessor motherboard: 2 CPUs cpu0 (BSP): apic id: 3, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x000f0011, at 0xfec00000 io1 (APIC): apic id: 1, version: 0x000f0011, at 0xfec01000 Preloaded elf kernel "kernel" at 0xc03ec000. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 11 entries at 0xc00f1010 acpi0: <ASUS CUR-DLS > on motherboard acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-safe" frequency 3579545 Hz acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_button0: <Power Button> on acpi0 acpi_timer0: <32-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard IOAPIC #1 intpin 4 -> irq 2 IOAPIC #1 intpin 2 -> irq 3 IOAPIC #1 intpin 14 -> irq 4 pci0: <PCI bus> on pcib0 fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd800-0xd83f mem 0xfd800000-0xfd8fffff,0xfe000000-0xfe000fff irq 2 at device 2.0 on pci0 fxp0: Ethernet address 00:e0:18:0a:97:a6 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.42> port 0xd400-0xd43f mem 0xfc800000-0xfc81ffff,0xfd000000-0xfd01ffff irq 3 at device 5.0 on pci0 em0: Speed:N/A Duplex:N/A pci0: <ATI Mach64-GR graphics accelerator> at 7.0 isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <ServerWorks ROSB4 ATA33 controller> port 0xb800-0xb80f at device 15.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 ohci0: <OHCI (generic) USB controller> mem 0xfa000000-0xfa000fff irq 4 at device 15.2 on pci0 usb0: OHCI version 1.0, legacy support usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 4 ports with 4 removable, self powered pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> on motherboard IOAPIC #1 intpin 8 -> irq 10 IOAPIC #1 intpin 9 -> irq 11 pci1: <PCI bus> on pcib1 sym0: <896> port 0xb400-0xb4ff mem 0xf9000000-0xf9001fff,0xf9800000-0xf98003ff irq 10 at device 5.0 on pci1 sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym1: <896> port 0xb000-0xb0ff mem 0xf8000000-0xf8001fff,0xf8800000-0xf88003ff irq 11 at device 5.1 on pci1 sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. orm0: <Option ROMs> at iomem 0xc0000-0xca7ff,0xd0000-0xd17ff,0xd4000-0xd7fff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: failed to get data. psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 sio1: configured irq 3 not in bitmap of probed irqs 0 ppc0: parallel port not found. APIC_IO: Testing 8254 interrupt delivery APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 intpin 2 APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0 SMP: AP CPU #1 Launched! acd0: CDROM <QSI CD-ROM SCR-242> at ata0-master PIO4 Waiting 5 seconds for SCSI devices to settle (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered. sa0 at sym1 bus 0 target 2 lun 0 sa0: <TANDBERG SLR100 0402> Removable Sequential Access SCSI-2 device sa0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit) da0 at sym0 bus 0 target 0 lun 0 da0: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da0: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) da3 at sym0 bus 0 target 3 lun 0 da3: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da3: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da3: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) da2 at sym0 bus 0 target 2 lun 0 da2: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da2: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) da1 at sym0 bus 0 target 1 lun 0 da1: <SEAGATE ST318436LW 0010> Fixed Direct Access SCSI-3 device da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled da1: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C) em0: Link is up 1000 Mbps Full Duplex After I plug my USB drive: amanda<root>46: usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), (0x1166)(0x0000), rev 1.00 port 1 powered port 2 powered port 3 powered port 4 powered amanda<root>47: camcontrol devlist -v scbus0 on sym0 bus 0: <SEAGATE ST318436LW 0010> at scbus0 target 0 lun 0 (pass0,da0) <SEAGATE ST318436LW 0010> at scbus0 target 1 lun 0 (pass1,da1) <SEAGATE ST318436LW 0010> at scbus0 target 2 lun 0 (pass2,da2) <SEAGATE ST318436LW 0010> at scbus0 target 3 lun 0 (pass3,da3) < > at scbus0 target -1 lun -1 () scbus1 on sym1 bus 0: <TANDBERG SLR100 0402> at scbus1 target 2 lun 0 (pass4,sa0) < > at scbus1 target -1 lun -1 () scbus-1 on xpt0 bus 0: < > at scbus-1 target -1 lun -1 (xpt0) Any help appreciated. Only difference I see, except the release level is that my trimed kernel includes ACPI and is SMP. Best regards, Olivier
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200705110614.l4B6E2QU052996>