Date: Wed, 08 Jun 2005 07:01:01 -0700 From: Mike Harding <mvh@ix.netcom.com> To: freebsd-amd64@freebsd.org Subject: Follow-up - K8T890 where everything works (Soltek, recommended) Message-ID: <1118239261.1281.9.camel@bsd.mvh>
next in thread | raw e-mail | index | archive | help
I purchased a Soltek SL-K890Pro-939 mainboard at NewEgg for $98 and it's
been rock-solid and everything I have tried has worked well. On board
sound, on-board ethernet, USB, everything. I have included the 'dmesg'
output below - note that I also have an M-Audio board installed, so it
shows up as unknown hardware. I am using the M-Audio board via the
4front driver but I did test out the onboard audio.
Recommended if you are looking for a FreeBSD compatible AMD-64 MB. Easy
setup and everything I have tried works well. I've booted the system in
both i386 and amd64 mode. I am also running a 'Cool n' quiet' kernel
module, it does keep the chip temps down when the system is idle.
The board appears to be of very good quality, and has an, er,
'interesting' color scheme, with lots of purple and some yellow, good
for Lakers' fans I suppose.
I am including the 'dmesg' output below. Can somebody tell me what
'acpi_bus_number: can't get _ADR' means?
I will put this on the supported MB page soon, after I incorporate
feedback to this post.
bash-2.05b$ dmesg
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE-p1 #0: Tue Jun 7 09:41:09 PDT 2005
root@bsd.mvh:/usr/obj/usr/src/sys/MVH
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 Processor 3700+ (2199.77-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x20f71 Stepping = 1
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500000<NX,AMIE,LM,DSP,3DNow!>
real memory = 1072562176 (1022 MB)
avail memory = 1035833344 (987 MB)
ACPI APIC Table: <K8T890 AWRDACPI>
ioapic0 <Version 0.3> irqs 0-23 on motherboard
ioapic1 <Version 0.3> irqs 24-47 on motherboard
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <K8T890 AWRDACPI> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral, interrupt controller> at device 0.5 (no driver
attached)
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 27 at device 2.0 on pci0
pci2: <ACPI PCI bus> on pcib2
nvidia0: <GeForce 6600 GT> mem
0xd4000000-0xd4ffffff,0xc8000000-0xcfffffff,0xd0000000-0xd3ffffff irq 24
at device 0.0 on pci2
pcib3: <ACPI PCI-PCI bridge> irq 31 at device 3.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 35 at device 3.1 on pci0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> irq 39 at device 3.2 on pci0
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> irq 43 at device 3.3 on pci0
pci6: <ACPI PCI bus> on pcib6
re0: <RealTek 8169SB Single-chip Gigabit Ethernet> port 0xd000-0xd0ff
mem 0xdc040000-0xdc0400ff irq 17 at device 6.0 on pci0
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
re0: Ethernet address: 00:e0:4c:00:60:67
atapci0: <Promise PDC20579 SATA150 controller> port
0xd400-0xd4ff,0xe700-0xe77f mem
0xdc000000-0xdc01ffff,0xdc043000-0xdc043fff irq 19 at device 7.0 on pci0
atapci0: failed: rid 0x20 is memory, requested 4
ata2: channel #0 on atapci0
ata3: channel #1 on atapci0
ata4: channel #2 on atapci0
pci0: <multimedia, audio> at device 9.0 (no driver attached)
fwohci0: <VIA Fire II (VT6306)> port 0xe100-0xe17f mem
0xdc041000-0xdc0417ff irq 18 at device 12.0 on pci0
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:06:66:00:1e:78:bb
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:06:1e:78:bb
fwe0: Ethernet address: 02:11:06:1e:78:bb
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
atapci1: <VIA 6420 SATA150 controller> port
0xe600-0xe60f,0xe500-0xe503,0xe400-0xe407,0xe300-0xe303,0xe200-0xe207
irq 20 at device 15.0 on pci0
ata5: channel #0 on atapci1
ata6: channel #1 on atapci1
atapci2: <VIA 8237 UDMA133 controller> port
0xe800-0xe80f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0
ata0: channel #0 on atapci2
ata1: channel #1 on atapci2
uhci0: <VIA 83C572 USB controller> port 0xe900-0xe91f irq 21 at device
16.0 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xea00-0xea1f irq 21 at device
16.1 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xeb00-0xeb1f irq 21 at device
16.2 on pci0
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <VIA 83C572 USB controller> port 0xec00-0xec1f irq 21 at device
16.3 on pci0
usb3: <VIA 83C572 USB controller> on uhci3
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 16.4 (no driver attached)
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
pci0: <multimedia, audio> at device 17.5 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on
acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
ulpt0: HewLett Packard HP LaserJet 1200, rev 1.10/1.00, addr 2, iclass
7/1
ulpt0: using bi-directional mode
ums0: Logitech USB-PS/2 Optical Mouse, rev 2.00/13.00, addr 3, iclass
3/1
ums0: 4 buttons and Z dir.
Timecounter "TSC" frequency 2199768836 Hz quality 800
Timecounters tick every 1.000 msec
ipfw2 initialized, divert disabled, rule-based forwarding disabled,
default to accept, logging disabled
acd0: DVDR <NEC DVD RW ND-3520AW/3.04> at ata0-master UDMA33
ad10: 286168MB <ST3300831AS/3.01> [581421/16/63] at ata5-master SATA150
cd0 at ata0 bus 0 target 0 lun 0
cd0: <_NEC DVD_RW ND-3520AW 3.04> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Mounting root from ufs:/dev/ad10s2a
cpu0: Px state: P0, 2200MHz, 85300mW, 100us, 9us
cpu0: Px state: P1, 2000MHz, 83000mW, 100us, 9us
cpu0: Px state: P2, 1800MHz, 70400mW, 100us, 9us
cpu0: Px state: P3, 1000MHz, 36100mW, 100us, 9us
cpu0: Px method: AMD K8 Cool'n'Quiet
envy24ht: Recording is not possible with dsp0
envy24ht: Recording is not possible with dsp0
envy24ht: Recording is not possible with dsp1
envy24ht: Recording is not possible with dsp2
envy24ht: Recording is not possible with dsp3
envy24ht: Recording is not possible with dsp4
Softoss: Audio device #6 is write only
Softoss: Audio device #7 is write only
Softoss: Audio device #8 is write only
Softoss: Audio device #9 is write only
Softoss: Audio device #10 is write only
Softoss: Audio device #11 is write only
Softoss: Audio device #12 is write only
Softoss: Audio device #13 is write only
envy24ht: Recording is not possible with dsp0
envy24ht: Recording is not possible with dsp0
envy24ht: Recording is not possible with dsp1
envy24ht: Recording is not possible with dsp2
envy24ht: Recording is not possible with dsp3
envy24ht: Recording is not possible with dsp4
Softoss: Audio device #6 is write only
Softoss: Audio device #7 is write only
Softoss: Audio device #8 is write only
Softoss: Audio device #9 is write only
Softoss: Audio device #10 is write only
Softoss: Audio device #11 is write only
Softoss: Audio device #12 is write only
Softoss: Audio device #13 is write only
bash-2.05b$
--
Mike Harding <mvh@ix.netcom.com>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1118239261.1281.9.camel>