Date: Sun, 01 Dec 1996 21:36:41 +0100 From: Terje Normann Marthinussen <Terje.N.Marthinussen@cc.uit.no> To: freebsd-smp@freebsd.org Subject: Re: SMP-current status Message-ID: <199612012036.VAA10981@slibo.cc.uit.no> In-Reply-To: Your message of "Sun, 01 Dec 1996 19:28:52 MET." <199612011828.TAA08278@slibo.cc.uit.no>
next in thread | previous in thread | raw e-mail | index | archive | help
>Tried to compile it with options APIC_IO for the first time as well: >BIOS basemem (633K) != RTC basemem (640K), setting to BIOS value >unknown bus type: 'XPRESS' > >Warning: current SMP kernel only tested with 2 CPUs. >Please report the results to: <smp@freebsd.org> > <return> to continue... >Application Processor #2 starting! >Application Processor #3 starting! >Application Processor #3 failed! >Application Processor #4 starting! >Application Processor #4 failed! >Sizing memory.. >init386 done CR0 = 80000011 >Copyright (c) 1992-1996 FreeBSD Inc. >Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > >FreeBSD 3.0-SMP #0: Sun Dec 1 18:25:33 MET 1996 > terjem@quattro:/usr/src/sys/compile/netserver >FreeBSD/SMP: Multiprocessor motherboard > cpu0 (BSP): apic id: 0, version: 0x00030010 > cpu1 (AP): apic id: 2, version: 0x00030010 > cpu2 (AP): apic id: 3, version: 0x00030010 > cpu3 (AP): apic id: 4, version: 0x00030010 > io0 (APIC): apic id: 14, version: 0x000f0011 >Calibrating clock(s) relative to mc146818A clock ... i8254 clock: 1193177 Hz >CPU: Pentium (586-class CPU) > Origin = "GenuineIntel" Id = 0x52b Stepping=11 > Features=0x3bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC> >real memory = 134217728 (131072K bytes) >avail memory = 127418368 (124432K bytes) >eisa0: <INT3190 (System Board)> >Probing for devices on the EISA bus >Probing for devices on PCI bus 0: >chip0 <generic PCI bridge (vendor=8086 device=1225 subclass=0)> rev 2 on pci0:0 >chip1 <Intel 82375EB PCI-EISA bridge> rev 5 on pci0:14:0 >pci0:15:0: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >pci0:15:1: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >pci0:15:2: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >pci0:15:3: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >pci0:15:4: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >pci0:15:5: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >pci0:15:6: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >pci0:15:7: Intel Corporation, device=0x0008, class=0xff, subclass=0x00 [no >driver assigned] >Probing for devices on PCI bus 1: >chip2 <generic PCI bridge (vendor=8086 device=1225 subclass=0)> rev 2 on pci1:0 >vx0 <3COM 3C595 Fast Etherlink XL PCI> rev 0 int a irq 11 on pci1:12 >mii[*mii*]: disable 'auto select' with DOS util! address 00:60:97:12:60:e8 >ahc0 <Adaptec aic7870 SCSI host adapter> rev 3 int a irq 7 on pci1:13 >ahc0: Using left over BIOS settings >ahc0: aic7870 Wide Channel, SCSI Id=7, 16 SCBs >ahc0 waiting for scsi devices to settle >Sending SDTR!! >(ahc0:0:0): "HP 2.13 GB 1st ### 1221" type 0 fixed SCSI 2 >sd0(ahc0:0:0): Direct-Access 2033MB (4165272 512 byte sectors) >(ahc0:5:0): "TOSHIBA CD-ROM XM-5301TA 1895" type 5 removable SCSI 2 >cd0(ahc0:5:0): CD-ROM >cd0(ahc0:5:0): NOT READY asc:3a,0 Medium not present >can't get the size >ahc1 <Adaptec aic7870 SCSI host adapter> rev 3 int a irq 10 on pci1:14 >ahc1: Using left over BIOS settings >ahc1: aic7870 Wide Channel, SCSI Id=6, 16 SCBs >ahc1 waiting for scsi devices to settle >Sending SDTR!! >(ahc1:4:0): "HP 2.13 GB 1st ### 1221" type 0 fixed SCSI 2 >sd1(ahc1:4:0): Direct-Access 2033MB (4165272 512 byte sectors) >Probing for devices on the ISA bus: >sc0 at 0x60-0x6f irq 1 on motherboard >sc0: VGA color <16 virtual consoles, flags=0x0> >sio0 at 0x3f8-0x3ff irq 4 on isa >sio0: type 16550A >sio1 not found at 0x2f8 >lpt0 not found at 0xffffffff >mse0 not found at 0x23c >fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa >fdc0: NEC 72065B >fd0: 1.44MB 3.5in >wdc0 not found at 0x1f0 >npx0 on motherboard >npx0: INT 16 interface >stray irq 13 >changing root device to sd0a >Enabled INTs: 1, 2, 4, 6, 7, 8, 10, 11, 13, imen: 0x00ffd229 >Rebooting... > > >It then just hang at Enabled. >"Rebooting..." came after ctrl-alt-delete This might be of a bit more help... I let it stay there for a couple of minutes the first time, but it seems like that wasn't enough, came to reboot again a bit later. Thought I had another kernel in /, went out of the room before it came up, and when I came back a lot later it said my kermit window (serial console is nice :)): changing root device to sd0a Enabled INTs: 1, 2, 4, 6, 7, 8, 10, 11, 13, imen: 0x00ffd229 sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0xb sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0xa ahc0: Issued Channel A Bus Reset. 1 SCBs aborted sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0xb6 SEQADDR == 0x3e sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0xb6 SEQADDR == 0x3e ahc0: Issued Channel A Bus Reset. 1 SCBs aborted sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 ahc0: Issued Channel A Bus Reset. 1 SCBs aborted sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 ahc0: Issued Channel A Bus Reset. 1 SCBs aborted sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 ahc0: Issued Channel A Bus Reset. 1 SCBs aborted sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 ahc0: Issued Channel A Bus Reset. 1 SCBs aborted sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 ahc0: Issued Channel A Bus Reset. 1 SCBs aborted sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 sd0(ahc0:0:0): timed out while idle, LASTPHASE == 0x1, SCSISIGI == 0x0 SEQADDR == 0x0 ahc0: Issued Channel A Bus Reset. 1 SCBs aborted panic (cpu#0): cannot mount root syncing disks... done Automatic reboot in 15 seconds - press a key on the console to abort --> Press a key on the console to reboot <-- Terje Marthinussen terjem@cc.uit.no
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199612012036.VAA10981>