Date: Fri, 29 Mar 2002 17:15:46 -0600 (CST) From: bdodson@scms.utmb.edu To: john@utzweb.net Cc: agorski@engin.umich.edu, freebsd-multimedia@FreeBSD.ORG Subject: Re: SB problem (was: Cat'ing /dev/audio) Message-ID: <200203292315.g2TNFmA97325@scms.utmb.edu> In-Reply-To: <Pine.LNX.4.44.0203291636540.7667-100000@jupiter.linuxengine.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Or moving the card to a different slot? But, from your posting to the list, it seems you don't have a problem any more, is that right? You guys have saturated my knowledge base :( Sorry Bud On 29 Mar, John Utz wrote: > that's an interesting result > > have you tried hardwiring the irq's in the bios? > > > On Fri, 29 Mar 2002, Adam D. Gorski wrote: > >> Ok.. I compared dmesg versus pciconf -l, and I found this.. I dunno if this >> means anything, but I figured I'd mention it... the first matching works, >> which is for my 3Com card: >> >> * dmesg: >> xl0: <3Com 3c900B-TPO Etherlink XL> port 0xd000-0xd07f mem >> 0xe1000000-0xe100007f irq 9 at device 9.0 on pci0 >> >> * pciconf -l >> xl0@pci0:9:0: class=0x020000 card=0x900410b7 chip=0x900410b7 rev=0x04 >> hdr=0x00 >> >> So both show IRQ 9 (if I'm reading the output right) which seems fine.. >> but.. check out my RTL and SB outputs: >> >> * dmesg >> rl0: <RealTek 8139 10/100BaseTX> port 0x9800-0x98ff mem >> 0xe0000000-0xe00000ff irq 11 at device 12.0 on pci0 >> >> pcm0: <Creative CT5880-C> port 0xa000-0xa03f irq 10 at device 11.0 on pci0 >> >> * pciconf -l >> rl0@pci0:12:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10 >> hdr=0x00 >> >> pcm0@pci0:11:0: class=0x040100 card=0x20001274 chip=0x58801274 rev=0x02 >> hdr=0x00 >> >> >> Ok, notice how one lists the SB @ IRQ 10, while the other shows it @ IRQ 11? >> I dunno, just something that caught my eye based on the suggestions below. >> >> Maybe this helps, >> >> - Adam >> >> >> On Fri, 29 Mar 2002 bdodson@scms.utmb.edu wrote: >> >> ::On 29 Mar, Adam D. Gorski wrote: >> ::> Hey, >> ::> >> ::> Thanks for the response. I went into my BIOS and told it that I don't have a >> ::> PnP OS, but the modules still did not detect the card. So I re-compiled the >> ::> kernel with 'device pcm', and the card is detected once again, but the >> ::> problems persist. I'm going to try some things that were suggested still, >> ::> and hopefully I'll get at least a step closer to the solution. Thanks once >> ::> again! >> ::> >> ::> - Adam >> ::> >> :: >> ::Hmm... I'm out of ideas. The bare 'device pcm' is right for devices >> ::being configured by pnp (as all pci devices are). 'device pcm0 ......' >> ::is right for devices which need to be hand configured (only isa or >> ::pccard devices). It sounds to me like you may have pci irq (or other >> ::resource) conflicts. You might try to do >> :: >> ::pciconf -vl (as root) >> :: >> ::and see if anything shows up that looks obviously bogus. I'm sorry I >> ::can't help you with the interpretation, but if you post the result to >> ::the multimedia list, this may allow them to give you better help. >> :: >> ::Good luck, >> ::Bud >> :: >> ::> On Fri, 29 Mar 2002 bdodson@scms.utmb.edu wrote: >> ::> >> ::> ::(reading your post via the archives, not subscribed to multimedia) >> ::> :: >> ::> ::I'm sure that someone will point out that FreeBSD is NOT a "PnP OS", so >> ::> ::you need to set your BIOS to "PnP OS = NO". I have no idea whether that >> ::> ::will fix your problem, but I know for sure setting it to YES is wrong. >> ::> ::That is probably why the modules did not work right: nothing is >> ::> ::configuring PNP. >> ::> :: >> ::> ::Good luck, >> ::> ::Bud Dodson >> ::> :: >> :: >> :: -- M. L. Dodson bdodson@scms.utmb.edu 409-772-2178 FAX: 409-772-1790 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-multimedia" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200203292315.g2TNFmA97325>