From owner-freebsd-questions Tue Oct 16 12:44: 7 2001 Delivered-To: freebsd-questions@freebsd.org Received: from inetgw.TandG.de (inetgw.TandG.de [194.76.146.30]) by hub.freebsd.org (Postfix) with ESMTP id DF4C937B408; Tue, 16 Oct 2001 12:44:00 -0700 (PDT) Received: (from mail@localhost) by inetgw.TandG.de (8.7.6/8.7.3) id WAA01277; Tue, 16 Oct 2001 22:35:34 +0200 (MET DST) X-Authentication-Warning: inetgw.TandG.de: mail set sender to using -f Received: from as.tandg.de(10.1.10.100) by inetgw.TandG.de via smap (V1.3) id sma001275; Tue Oct 16 22:35:23 2001 Received: from TandG.de (tgalto.TandG.de [10.1.10.120]) by as.TandG.de (8.7.6/8.7.3) with ESMTP id VAA08681; Tue, 16 Oct 2001 21:35:04 GMT Message-ID: <3BCC8DA3.C913860F@TandG.de> Date: Tue, 16 Oct 2001 21:42:27 +0200 From: Han Timmerman Organization: Timmerman & Gerber GmbH X-Mailer: Mozilla 4.72 [en] (WinNT; I) X-Accept-Language: en MIME-Version: 1.0 To: freebsd-questions@freebsd.org Cc: dougb@freebsd.org Subject: Re: conf/31305: Pre-Installation from FreeBSD 4.4 CDROM hangs after plip0 ... on ppbus0 References: <200110152241.f9FMfQF66976@freefall.freebsd.org> Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk List-ID: List-Archive: (Web Archive) List-Help: (List Instructions) List-Subscribe: List-Unsubscribe: X-Loop: FreeBSD.ORG Hi, meanwhile I have been trying out a few things. I removed the 3Com905 card and replaced it by an Intel Pro/100S card. 3com cards are known for bus conflict situations anyway. The result, though, stays the same. The system hangs as discussed. So I tried the older 4.3 CDROM and that works fine. So I closely looked at both installation printouts and noticed one big difference. The "orm0" device is detected during the startup phase of 4.4. The 4.3 startup phase does NOT show this device. The address range displayed for the "orm0" device looks pretty much like the IO memory of my RAID controller. Could we have a problem here? I could not find a way to disable the "orm0" device in the kernel configuration part. Is there a way to disable or remove this device? Best Regards, Han dougb@FreeBSD.org wrote: > Synopsis: Pre-Installation from FreeBSD 4.4 CDROM hangs after plip0 ... on ppbus0 > > State-Changed-From-To: open->closed > State-Changed-By: dougb > State-Changed-When: Mon Oct 15 15:40:07 PDT 2001 > State-Changed-Why: > > Please send this information to freebsd-questions@freebsd.org. You've covered > most of the bases, but you should also include whether your conflicts were > all resolved when you finished the configure for the 4.4 install. Also, > have you changed anything in your BIOS settings between the two installs? > Specifically related to the PnP options? > > Good luck, > > Doug > > http://www.FreeBSD.org/cgi/query-pr.cgi?pr=31305 -- Han Timmerman mailto:han@TandG.de Timmerman & Gerber GmbH phone: +49 8254 8005 Dr. Jakob-Scheckh-Strasse 7 fax: +49 8254 8538 D-85250 Altomuenster http://www.TandG.de/ Germany mailto:info@TandG.de To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message