Date: Mon, 3 Dec 2001 18:52:52 -0700 From: Chad David <davidc@acns.ab.ca> To: freebsd-stable@freebsd.org Subject: SMP beeping Message-ID: <20011203185252.A336@colnta.acns.ab.ca>
next in thread | raw e-mail | index | archive | help
I upgraded one of my servers to stable this afternoon only to
find that if SMP is enabled the pc speaker starts to beep on
and off in a somewhat random pattern forever.... If I boot a
GENERIC kernel without SMP the beeping goes away, if I then
only add the two SMP related lines the beeping starts again.
I've narrowed it down that the time the second cpu is started
is the time the beeping begins. What is strange that if I then
boot into a GENERIC kernel it will continue to beep at strange
points (the bios netboot prompt, just prior to the loader count
down, at the copywrite printout etc.), but somewhere during the
boot it fixes itself. If I reboot into GENERIC again all is
normal (no strange beeps).
Does this "ring a bell" with anybody?
Here is the dmesg for what its worth:
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.4-STABLE #1: Mon Dec 3 18:48:58 MST 2001
root@colnta:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (1004.52-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 1073725440 (1048560K bytes)
avail memory = 1041096704 (1016696K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 3, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00178011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc0499000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 7 entries at 0xc00f12d0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 10
pci0: <PCI bus> on pcib0
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <ATI Mach64-GB graphics accelerator> at 0.0 irq 2
isab0: <VIA 82C686 PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0xb800-0xb80f at device 4.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <NVidia model 0110 graphics accelerator> at 12.0 irq 2
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xa800-0xa87f mem 0xeb800000-0xeb80007f irq 10 at device 13.0 on pci0
xl0: Ethernet address: 00:01:02:47:d5:14
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc87ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: failed to get data.
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <Hewlett-Packard HP LaserJet 1200> PRINTER PJL,MLC,PCL,PCLXL,POSTSCRIPT
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
ad0: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata0-master tagged UDMA100
ad1: 39266MB <IC35L040AVER07-0> [79780/16/63] at ata0-slave tagged UDMA100
ad2: 9765MB <FUJITSU MPC3102AT E> [19841/16/63] at ata1-master UDMA33
acd0: CDROM <LG CD-ROM CRD-8522B> at ata1-slave using PIO4
Mounting root from ufs:/dev/ad2s1a
--
Chad David davidc@acns.ab.ca
ACNS Inc. Calgary, Alberta Canada
--
Chad David davidc@acns.ab.ca
ACNS Inc. Calgary, Alberta Canada
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20011203185252.A336>