Date: Thu, 16 Apr 1998 00:04:08 +0100 From: Karl Pielorz <kpielorz@tdx.co.uk> To: Shawn Ramsey <shawn@luke.cpl.net> Cc: questions@FreeBSD.ORG Subject: Re: bpfilter Message-ID: <35353CE8.7D030059@tdx.co.uk> References: <Pine.BSF.3.95.980415155640.5889A-100000@luke.cpl.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Holy Cow! ;-) (or should I say - Holy Daemon! <g>) Erm, have you tried running trafshow with '-i interface', e.g. '-i eth2' etc? I can see why it would think eth0 is not configured (as it doesn't have a valid IP address etc.) If eth2 doesn't work try etha16, 17, 18, 19, 20 etc... ;-) Other than that - you'll have to wait for someone who's seen one of these before to advise you... <g> Regards, Karl Pielorz Shawn Ramsey wrote: > > > > > What device does the T1 card usually map to? (i.e. whats the output of an > > 'ifconfig -a' on your machine?) - what command line are you using to run > > 'trafshow'? > > > > Regards, > > Here is the output of ifconfig -a : > > eth0: flags=41<UP,RUNNING> mtu 1500 > eth1: flags=10<POINTOPOINT> mtu 1500 > eth2: flags=51<UP,POINTOPOINT,RUNNING> mtu 1500 > inet 209.150.92.241 --> 209.150.92.242 netmask 0xffffff00 > eth3: flags=41<UP,RUNNING> mtu 1500 > fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > inet 209.150.92.1 netmask 0xffffffe0 broadcast 209.150.92.31 > inet 209.203.66.1 netmask 0xfffffff0 broadcast 209.203.66.15 > ether 00:a0:c9:95:0f:31 > media: autoselect > lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500 > bw0: flags=0<> > tun0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500 > sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552 > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 > inet 127.0.0.1 netmask 0xff000000 > etha16: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500 > inet 208.153.225.234 --> 208.153.225.233 netmask 0xffffff00 > ethd16: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500 > inet 209.150.92.253 --> 209.150.92.254 netmask 0xffffff00 > ethd17: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500 > inet 209.150.92.249 --> 209.150.92.250 netmask 0xffffff00 > ethd18: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500 > inet 204.137.203.94 --> 204.137.203.93 netmask 0xffffff00 > ethd19: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500 > inet 209.203.66.253 --> 209.203.66.254 netmask 0xffffff00 > ethd20: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500 > inet 209.150.92.237 --> 209.150.92.238 netmask 0xffffff00 > ethd21: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500 > inet 209.150.92.233 --> 209.150.92.234 netmask 0xffffff00 > > running trafshow with just the program name, have tried -p with no success > either. To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?35353CE8.7D030059>